What did you do to your truck today! - Page 343 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

BugzC10 · 12-19-2013, 09:15 AM

That looks great! what are the specs on the wheels?

[/QUOTE]

X2 really like that look! Who's the mfr?

texjake · 12-19-2013, 10:28 PM

I finished installing the passenger side window regulator, the new window channel weather stripping (door glass felt run channel) and the fuzzies aka the scrappers or anti-rattle are installed. The junk yard/new window regulator works great! The window doesn't fall down now when I shut the door. And I didn't even break the glass putting it back in, kudos to me! Now I'm just waiting for the new arm rests to come in.

effects66 · 12-19-2013, 10:56 PM

Quote:

Originally Posted by BugzC10

That looks great! what are the specs on the wheels?

X2 really like that look! Who's the mfr?[/QUOTE]

Circle Racing

circleracing.com

They are 20x10 rear and 20x8.5 fronts

In The Ten Ring · 12-20-2013, 01:29 AM

I tried (in vain) to see if I could get a fellow board member to part out his stepside bed so I could get his passenger side fender. Oh well, I ended up encouraging him to sell it all at once then prayed that he could.

It was cool talking with a fellow member and that made the call worthwhile.

ole dollor · 12-20-2013, 03:25 PM

Quote:

Originally Posted by texjake

I finished installing the passenger side window regulator, the new window channel weather stripping (door glass felt run channel) and the fuzzies aka the scrappers or anti-rattle are installed. The junk yard/new window regulator works great! The window doesn't fall down now when I shut the door. And I didn't even break the glass putting it back in, kudos to me! Now I'm just waiting for the new arm rests to come in.

looking good . keep up the good work.

texjake · 12-20-2013, 04:31 PM

Quote:

Originally Posted by ole dollor

looking good . keep up the good work.

Thanks ole, it just takes a little time & a whole lot of money. But hey, that's what makes it fun!

alloutpro · 12-20-2013, 07:18 PM

Put all new fuel lines and fuel pump...went for a cruise and wasted an hour drooling on a new tranny.......

Lees68GMC · 12-20-2013, 07:27 PM

Hey Texjake, It's snowing here and I have to work outside, so not doing it right now, But I have the window channels, (whole kit & trim everything you mentioned) and rubber Vent window gaskets also complete. Any insights, tricks to make it easier or just go for the obvious?
- Lee

jeh · 12-21-2013, 12:29 AM

Quote:

Originally Posted by In The Ten Ring

I tried (in vain) to see if I could get a fellow board member to part out his stepside bed so I could get his passenger side fender. Oh well, I ended up encouraging him to sell it all at once then prayed that he could.

It was cool talking with a fellow member and that made the call worthwhile.

I won't forget about you if the complete bed don't sell. It was nice talking with you also. I enjoyed your "trip to the hospital" story. After we got off the phone I told my wife about it.....

allens4876 · 12-21-2013, 01:20 AM

today i installed the hei distributor, replaced the thermostat, and started on my 5 speed swap. i cut out the small hump and drilled holes for the high hump. i searched for a shifter, but to no luck. the shifter for the 90 nv3500 has been discontinued. so i made one myself, glad i did too because i paid a total of $0.64 for it. i had a long piece of rod laying in the garage i used.

texjake · 12-21-2013, 01:46 AM

Quote:

Originally Posted by Lees68GMC

Hey Texjake, It's snowing here and I have to work outside, so not doing it right now, But I have the window channels, (whole kit & trim everything you mentioned) and rubber Vent window gaskets also complete. Any insights, tricks to make it easier or just go for the obvious?
- Lee

Don't feel bad, I do all my work on my truck outside as well, so I know how you feel. I have sent you a PM on how I tackled the task of replacing the window weather stripping & the fuzzies aka anti-rattles & the scrappers.

Andy4639 · 12-21-2013, 08:51 AM

I'm having the 305 TPI motor swapped out for a 6.0 LSx motor.
Hawks 3rd gen Camaro is doing the work.

lolo33 · 12-21-2013, 09:05 AM

try to find the issue with contact. i have battery, but no contact ..... and no electricity !!

texjake · 12-21-2013, 02:41 PM

Quote:

Originally Posted by lolo33

try to find the issue with contact. i have battery, but no contact ..... and no electricity !!

Check your ground strap between your engine or frame to the one connected to your cab. That is if your battery is fully charged.

lolo33 · 12-21-2013, 03:05 PM

thanks. After control, it was just a little issue with battery clip.
now it works

john@thepier · 12-21-2013, 05:03 PM

I called the owner of the body/shop today that has had my truck for like 8 years and told him to get working on it, I've done this every other month for years now. I also told him that I just may have to take his butt to court if he did not get it done, or give me all my money back that I have paid him in advance and I'll find another shop to finish it. Guy offered me a deal, which I have in writing on the labor rate for helping him out $ during a hard time he was having. Hardly a deal when its taking this long. Granted though I never did put in a date of completion, and the work he is doing is the very top on notches. Money always seems to make enemies out of friends. So I guess I did at least something for my truck today!! Ha. John

Molberg · 12-21-2013, 05:32 PM

Quote:

Originally Posted by john@thepier

I called the owner of the body/shop today that has had my truck for like 8 years and told him to get working on it, I've done this every other month for years now. I also told him that I just may have to take his butt to court if he did not get it done, or give me all my money back that I have paid him in advance and I'll find another shop to finish it. Guy offered me a deal, which I have in writing on the labor rate for helping him out $ during a hard time he was having. Hardly a deal when its taking this long. Granted though I never did put in a date of completion, and the work he is doing is the very top on notches. Money always seems to make enemies out of friends. So I guess I did at least something for my truck today!! Ha. John

Wow! Hope all turns out well after such a long wait

mud.man.rj · 12-21-2013, 08:24 PM

That is extremely long on the truck, but sounds like things will start to happen now, to bad it has to be that hard.

In The Ten Ring · 12-22-2013, 07:17 PM

I went over to Sears and picked up my Craftsman Double Flare Kit for when I replace my entire fuel (hard) lines.

dirtymax67 · 12-22-2013, 11:13 PM

Finally got the truck in the garage so I can begin work on it

Gor77 · 12-23-2013, 06:38 AM

Bhelton · 12-23-2013, 06:54 AM

Installed serpentine system, waiting on under drive pulleys to arrive today or tomorrow.

legotech7 · 12-23-2013, 02:23 PM

Maybe some of you can do some video's on the metal work you do on your trucks, so the rest of us novices might learn something... Nice work......

Rylie · 12-23-2013, 05:28 PM

Blasted, Primed, Sprayed with 2 coats of 2k epoxy bedliner. Made good progress today.

VWNate1 · 12-23-2013, 08:04 PM

Wow ;

So much hard works ! great to look at . especially the welding & body works .

I'm back from the Hospital , the neck surgery seems to have gone well , now I wait until March before being allowed to pick up my tools again .

12-19-2013, 09:15 AM	#8551
BugzC10 Registered User Join Date: Oct 2012 Location: Rose Hill Kansas Posts: 1,351	Re: What did you do to your truck today! That looks great! what are the specs on the wheels?[/QUOTE] X2 really like that look! Who's the mfr? __________________ 1970 C10 Short Stepper with 71/72 front clip.

12-19-2013, 10:28 PM	#8552
texjake Registered User Join Date: Nov 2013 Location: Lubbock, TX Posts: 283	Re: What did you do to your truck today! I finished installing the passenger side window regulator, the new window channel weather stripping (door glass felt run channel) and the fuzzies aka the scrappers or anti-rattle are installed. The junk yard/new window regulator works great! The window doesn't fall down now when I shut the door. And I didn't even break the glass putting it back in, kudos to me! Now I'm just waiting for the new arm rests to come in. Attached Images

12-20-2013, 01:29 AM	#8554
In The Ten Ring Registered User Join Date: Jun 2013 Location: West Virginia Posts: 6,427	Re: What did you do to your truck today! I tried (in vain) to see if I could get a fellow board member to part out his stepside bed so I could get his passenger side fender. Oh well, I ended up encouraging him to sell it all at once then prayed that he could. It was cool talking with a fellow member and that made the call worthwhile.

12-20-2013, 07:18 PM	#8557
alloutpro Registered User Join Date: Nov 2013 Location: ventura,CA Posts: 33	Re: What did you do to your truck today! Put all new fuel lines and fuel pump...went for a cruise and wasted an hour drooling on a new tranny....... __________________ Roll Tide! '69 C20 Longhorn 396

12-20-2013, 07:27 PM	#8558
Lees68GMC Registered User Join Date: Jul 2013 Location: Prescott Arizona Posts: 343	Re: What did you do to your truck today! Hey Texjake, It's snowing here and I have to work outside, so not doing it right now, But I have the window channels, (whole kit & trim everything you mentioned) and rubber Vent window gaskets also complete. Any insights, tricks to make it easier or just go for the obvious? - Lee __________________ 68 GMC SWB Vortec 5.3 98 Chevy Blazer ZR2 94 Mazda Miata, LS2 6 speed, sold "No matter what happens, nobody gets out alive"

12-21-2013, 01:20 AM	#8560
allens4876 Registered User Join Date: Nov 2013 Location: knoxville, tn Posts: 28	Re: What did you do to your truck today! today i installed the hei distributor, replaced the thermostat, and started on my 5 speed swap. i cut out the small hump and drilled holes for the high hump. i searched for a shifter, but to no luck. the shifter for the 90 nv3500 has been discontinued. so i made one myself, glad i did too because i paid a total of $0.64 for it. i had a long piece of rod laying in the garage i used.

12-21-2013, 08:51 AM	#8562
Andy4639 Old member Join Date: Jan 2002 Location: Liberty, & Garden City S.C. , U.S. Posts: 19,945	Re: What did you do to your truck today! I'm having the 305 TPI motor swapped out for a 6.0 LSx motor. Hawks 3rd gen Camaro is doing the work. Attached Images __________________ 1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.

12-21-2013, 09:05 AM	#8563
lolo33 Registered User Join Date: Jun 2012 Location: Givors - FRANCE Posts: 109	Re: What did you do to your truck today! try to find the issue with contact. i have battery, but no contact ..... and no electricity !! __________________ '70 C10 shortbed - 350 Edelbrock equipped - 4/1 headers - 3" flowmaster exausts '07 MUSTANG V8 convertible - CAI Spectre - Brembo's - 3" flowmaster exhausts

12-21-2013, 03:05 PM	#8565
lolo33 Registered User Join Date: Jun 2012 Location: Givors - FRANCE Posts: 109	Re: What did you do to your truck today! thanks. After control, it was just a little issue with battery clip. now it works __________________ '70 C10 shortbed - 350 Edelbrock equipped - 4/1 headers - 3" flowmaster exausts '07 MUSTANG V8 convertible - CAI Spectre - Brembo's - 3" flowmaster exhausts

12-21-2013, 05:03 PM	#8566
john@thepier Senior Member Join Date: Aug 2004 Location: Lake Geneva, WI 53147 Posts: 970	Re: What did you do to your truck today! I called the owner of the body/shop today that has had my truck for like 8 years and told him to get working on it, I've done this every other month for years now. I also told him that I just may have to take his butt to court if he did not get it done, or give me all my money back that I have paid him in advance and I'll find another shop to finish it. Guy offered me a deal, which I have in writing on the labor rate for helping him out $ during a hard time he was having. Hardly a deal when its taking this long. Granted though I never did put in a date of completion, and the work he is doing is the very top on notches. Money always seems to make enemies out of friends. So I guess I did at least something for my truck today!! Ha. John

12-21-2013, 08:24 PM	#8568
mud.man.rj Registered User Join Date: Dec 2011 Location: Creighton Sask. Canada Posts: 4,121	Re: What did you do to your truck today! That is extremely long on the truck, but sounds like things will start to happen now, to bad it has to be that hard. __________________ 1987 Green n Green machine. 5.0 4spd std. 7" lift w 35's.

12-22-2013, 07:17 PM	#8569
In The Ten Ring Registered User Join Date: Jun 2013 Location: West Virginia Posts: 6,427	Re: What did you do to your truck today! I went over to Sears and picked up my Craftsman Double Flare Kit for when I replace my entire fuel (hard) lines.

12-22-2013, 11:13 PM	#8570
dirtymax67 Registered User Join Date: Oct 2013 Location: Lancaster, ky Posts: 21	Re: What did you do to your truck today! Finally got the truck in the garage so I can begin work on it __________________ 67 C10 stepside long bed. 250 inline, 3 on the tree.

12-23-2013, 06:38 AM	#8571
Gor77 Registered User Join Date: Sep 2012 Location: Moscow, Russia Posts: 347	Re: What did you do to your truck today! __________________ ___________________________________ Dima 1970 Chevrolet C10 stepside http://67-72chevytrucks.com/vboard/s...d.php?t=569197

12-23-2013, 06:54 AM	#8572
Bhelton Registered User Join Date: May 2012 Location: Hickory NC Posts: 2,351	Re: What did you do to your truck today! Installed serpentine system, waiting on under drive pulleys to arrive today or tomorrow. Attached Images



Register or Log In To remove these advertisements.

12-23-2013, 02:23 PM	#8573
legotech7 Registered User Join Date: Aug 2013 Location: Kannapolis NC Posts: 193	Re: What did you do to your truck today! Maybe some of you can do some video's on the metal work you do on your trucks, so the rest of us novices might learn something... Nice work......

12-23-2013, 05:28 PM	#8574
Rylie Registered User Join Date: Dec 2013 Location: West Palm Beach, FL Posts: 8	Re: What did you do to your truck today! Blasted, Primed, Sprayed with 2 coats of 2k epoxy bedliner. Made good progress today. Attached Images

12-23-2013, 08:04 PM	#8575
VWNate1 Registered User Join Date: Feb 2012 Location: So. Cali. Posts: 2,659	Re: What did you do to your truck today! Wow ; So much hard works ! great to look at . especially the welding & body works . I'm back from the Hospital , the neck surgery seems to have gone well , now I wait until March before being allowed to pick up my tools again . __________________ -Nate Geezer '49 3100 235 W/ Muncie SM420 SOLD '69 C/10 shortbed sidemount survivor 250 L6 W/ 350TH

Register or Log In To remove these advertisements.