Ok Boys and Girls it's Storytime - Page 35 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

SCOTI · 10-05-2021, 12:44 PM

Quote:

Originally Posted by aggie91

Dang that sucks. Hopefully there is not any major damage inside.

x2. And.... How the heck did it happen?

**regan wilson** · 10-05-2021, 07:21 PM

Quote:

Originally Posted by SCOTI

x2. And.... How the heck did it happen?

I don't know guys. I wish I could question the other end of that damn bolt. I looked for that SOB and the rest of the missing pieces till I just had to give up and go home. I worked a couple of hours this afternoon and got the motor out and on the stand. I pulled the intake and the D/S system. I'll try to get it all the way down tomorrow evening.

**mongocanfly** · 10-06-2021, 07:02 AM

dang the bad luck...

71Dragtruck · 10-06-2021, 08:24 PM

$hitty deal!

**regan wilson** · 10-06-2021, 08:46 PM

I got it down to the short block today. I don't think it's too bad. I'll report back tomorrow. The rods moved back and forth so that's good.

**regan wilson** · 10-09-2021, 09:35 PM

I think I dodged a bullet. It was trying to eat the 3 and 4 main bearings. I'm going to set up an Idiot light on an oil pressure sensor. I am getting old ya know.

litebulblsc · 10-13-2021, 08:51 PM

Maybe look into an accusump?

**regan wilson** · 10-14-2021, 07:40 AM

Quote:

Originally Posted by litebulblsc

Maybe look into an accusump?

It's on the shelf. I ran one for years on my wet sump. I took it off when I did the dry sump deal. I dropped a Melling pump in the pan back in 2005. The Accusump saved the mains but not the rods. It doesn't matter if you're not paying attention. Hence the idiot light. I also thought about a mechanical hand hooked to a pressure switch. No pressure? Slaps me in the head! Lol

**regan wilson** · 10-14-2021, 07:56 AM

My plan was to have it out after the Fall Nationals last weekend. I met one of Slick Rick's friends about an hour from home Sunday. He delivered my heads to Rick. That saved me a day. Monday I drove the 4 hour drive to Donnel's and dropped off the short block. I haven't talked to him since. But we think all the crank needs is a polish. We have to order pistons from JE, rods from GRP, rings from Total Seal, and lifters from Crower. Some parts have been two months out and worse. I want everything together by the end of January.

**regan wilson** · 10-14-2021, 08:04 AM

**regan wilson** · 10-14-2021, 08:05 AM

These were the black coated King Bearings. I think I wore the black off.

**regan wilson** · 10-14-2021, 08:06 AM

**regan wilson** · 10-18-2021, 08:36 AM

Well I had to get motivated and get started on the idiot light. I've ordered a pressure switch and an led light. It only took 30 minutes of contortionist moves to get the light switch out. The roll cage gets in the way of whatever you try to do. Ken showed up and helped get all the gauge lines pulled through the firewall. I've been wanting to give the cluster a refresh for awhile. I've just put it off because it's such a PITA to get out.

**regan wilson** · 10-18-2021, 08:45 AM

After that we were talking about Whitey. I told him it wasn't running. I've had problems where once it sat awhile it wouldn't start. I thought it was losing prime on the fuel. He asked if I had beat on the carb with a hammer? I said no. I filled the bowl with fuel and we beat on it when I started it. Tada it ran! We went for a ride and decided it was time for the muffler to come off. It leaked everywhere and sounded like it was on the verge of stopping up with all the loose pieces inside. Out came the sawzall and five minutes later it sounds like a hot rod Log Truck. It actually sounds pretty good. The carb is rich enough that it doesn't pop on deceleration.

**regan wilson** · 10-20-2021, 08:17 AM

I've gotten my gauge cluster all blown apart. I've been scrubbing and sanding on everything getting ready to repaint it all.

**regan wilson** · 10-20-2021, 08:25 AM

All I had time to do yesterday was get the placement I wanted for my LED warning light and drill a hole for it. I may add some more behind the fuel gage. It will be running off the key switched terminal on the fuse block. That means it also will tell me (Hey stupid! Turn the key off)

**regan wilson** · 10-20-2021, 08:42 PM

I got a call from Donnel today. The good news is my crank is straight as can be. The little bit of heat shrunk the main caps on 3 and 4. So all the block needs is an align hone..

**regan wilson** · 10-21-2021, 07:31 AM

I got started on painting yesterday. I's time consuming just trying to tape off all this mess. I'm going for more of an aluminum color to go with the Autometer gauges. After this color I have to go back and tape the fresh paint off to spray the black.

**regan wilson** · 10-22-2021, 07:30 AM

Progress.

**regan wilson** · 10-22-2021, 07:34 AM

I also made some new lenses behind the fuel gauge. The old ones were painted over. I stuck two of the LED lights in there. It's all wired together.

**regan wilson** · 10-22-2021, 07:38 AM

Almost done. I have some hand lettering and touch ups to do. I also repainted the blue inside.

Tada! We have light.

aggie91 · 10-22-2021, 08:52 AM

that turned out nice.

I'm guessing there might be a story behind the odometer reading...

**regan wilson** · 10-22-2021, 09:12 AM

Thanks Karl. The Odometer hasn't worked since 82. The truck had over 100,000 miles on it then. I twisted it around to 454 20 plus years ago.

**regan wilson** · 10-22-2021, 09:25 AM

I also found out yesterday per Peterson Fluid Systems. They don't do any v belt pulleys on their mandrels anymore. It seems they have had too many failures. Hmm. I'm going to have to convert my alternator over to the HTD type cogged belt like the Oil Pump.

LT7A · 10-25-2021, 01:31 AM

Regan, thanks for all the information and history that you've posted here. I just read the whole thing and it's quite a story. I go see the NHRA Northwest Nationals when they come to town, but didn't have much of an idea of what it takes for you to run in your class before reading all of this. Great looking truck, and I hope that you get the parts that you need soon.

10-06-2021, 07:02 AM	#853
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,662	Re: Ok Boys and Girls it's Storytime dang the bad luck... __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver

10-06-2021, 08:24 PM	#854
71Dragtruck Registered User Join Date: Jun 2004 Location: Saskatchewan, Canada Posts: 1,368	Re: Ok Boys and Girls it's Storytime $hitty deal! __________________ Speed is just a matter of money, question is how fast can you afford to go? 8.95@148.97mph all motor haven't tried bottle yet Sponsored by: Getz Oilfield Consulting Hard Candy Customs

10-06-2021, 08:46 PM	#855
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime I got it down to the short block today. I don't think it's too bad. I'll report back tomorrow. The rods moved back and forth so that's good. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

10-09-2021, 09:35 PM	#856
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime I think I dodged a bullet. It was trying to eat the 3 and 4 main bearings. I'm going to set up an Idiot light on an oil pressure sensor. I am getting old ya know. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

10-13-2021, 08:51 PM	#857
litebulblsc Registered User Join Date: Aug 2006 Location: LaSalle Mi Posts: 519	Re: Ok Boys and Girls it's Storytime Maybe look into an accusump?

10-14-2021, 07:56 AM	#859
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime My plan was to have it out after the Fall Nationals last weekend. I met one of Slick Rick's friends about an hour from home Sunday. He delivered my heads to Rick. That saved me a day. Monday I drove the 4 hour drive to Donnel's and dropped off the short block. I haven't talked to him since. But we think all the crank needs is a polish. We have to order pistons from JE, rods from GRP, rings from Total Seal, and lifters from Crower. Some parts have been two months out and worse. I want everything together by the end of January. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

10-14-2021, 08:04 AM	#860
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

10-14-2021, 08:05 AM	#861
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime These were the black coated King Bearings. I think I wore the black off. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

10-14-2021, 08:06 AM	#862
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

10-18-2021, 08:36 AM	#863
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime Well I had to get motivated and get started on the idiot light. I've ordered a pressure switch and an led light. It only took 30 minutes of contortionist moves to get the light switch out. The roll cage gets in the way of whatever you try to do. Ken showed up and helped get all the gauge lines pulled through the firewall. I've been wanting to give the cluster a refresh for awhile. I've just put it off because it's such a PITA to get out. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

10-18-2021, 08:45 AM	#864
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime After that we were talking about Whitey. I told him it wasn't running. I've had problems where once it sat awhile it wouldn't start. I thought it was losing prime on the fuel. He asked if I had beat on the carb with a hammer? I said no. I filled the bowl with fuel and we beat on it when I started it. Tada it ran! We went for a ride and decided it was time for the muffler to come off. It leaked everywhere and sounded like it was on the verge of stopping up with all the loose pieces inside. Out came the sawzall and five minutes later it sounds like a hot rod Log Truck. It actually sounds pretty good. The carb is rich enough that it doesn't pop on deceleration. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

10-20-2021, 08:17 AM	#865
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime I've gotten my gauge cluster all blown apart. I've been scrubbing and sanding on everything getting ready to repaint it all. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

10-20-2021, 08:25 AM	#866
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime All I had time to do yesterday was get the placement I wanted for my LED warning light and drill a hole for it. I may add some more behind the fuel gage. It will be running off the key switched terminal on the fuse block. That means it also will tell me (Hey stupid! Turn the key off) __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

10-20-2021, 08:42 PM	#867
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime I got a call from Donnel today. The good news is my crank is straight as can be. The little bit of heat shrunk the main caps on 3 and 4. So all the block needs is an align hone.. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

10-21-2021, 07:31 AM	#868
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime I got started on painting yesterday. I's time consuming just trying to tape off all this mess. I'm going for more of an aluminum color to go with the Autometer gauges. After this color I have to go back and tape the fresh paint off to spray the black. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph



Register or Log In To remove these advertisements.

10-22-2021, 07:30 AM	#869
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime Progress. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

10-22-2021, 07:34 AM	#870
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime I also made some new lenses behind the fuel gauge. The old ones were painted over. I stuck two of the LED lights in there. It's all wired together. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

10-22-2021, 07:38 AM	#871
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime Almost done. I have some hand lettering and touch ups to do. I also repainted the blue inside. Tada! We have light. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

10-22-2021, 08:52 AM	#872
aggie91 I'm just glad to be here! Join Date: Jan 2008 Location: Longview, TX Posts: 4,788	Re: Ok Boys and Girls it's Storytime that turned out nice. I'm guessing there might be a story behind the odometer reading... __________________ Karl 1965 Chevy Stepside(Grandpa's Old Blue) and (July 2015 Shop Build!)(2020, the Saga Continues) http://67-72chevytrucks.com/vboard/s...d.php?t=372424 The LST Challenge: http://67-72chevytrucks.com/vboard/s...=1#post7812257 Korbin's 1st Square: "Sunburn" http://67-72chevytrucks.com/vboard/s...d.php?t=418618 1985 GMC Sierra: "White Trash", Korbin's 2nd now... http://67-72chevytrucks.com/vboard/s...d.php?t=632305 Henry - 1984 Chevrolet, Owen's 1st Square

10-22-2021, 09:12 AM	#873
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime Thanks Karl. The Odometer hasn't worked since 82. The truck had over 100,000 miles on it then. I twisted it around to 454 20 plus years ago. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

10-22-2021, 09:25 AM	#874
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime I also found out yesterday per Peterson Fluid Systems. They don't do any v belt pulleys on their mandrels anymore. It seems they have had too many failures. Hmm. I'm going to have to convert my alternator over to the HTD type cogged belt like the Oil Pump. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

10-25-2021, 01:31 AM	#875
LT7A Registered User Join Date: Oct 2015 Location: PNW Posts: 3,615	Re: Ok Boys and Girls it's Storytime Regan, thanks for all the information and history that you've posted here. I just read the whole thing and it's quite a story. I go see the NHRA Northwest Nationals when they come to town, but didn't have much of an idea of what it takes for you to run in your class before reading all of this. Great looking truck, and I hope that you get the parts that you need soon.

Register or Log In To remove these advertisements.