|
|
|
08-06-2014, 02:04 PM
|
#1 |
|
Registered User
 
Join Date: Feb 2011
Location: Knoxville, TN
Posts: 362
|
Re: What did you do to your truck today? Chapter II
Well, so far today, I've installed a new spacer between the balancer and crank pulleys, mounted the right side motor mount, installed a new stainless heater hose fitting into the water pump, painted the short head bolts, cleaned up my carb and installed it with a new heat insulator gasket.
Later, I'll probably clean up the ram horns and brush Por-15 gray manifold coating on them. |
|
|
08-06-2014, 02:37 PM
|
#2 |
|
Registered User
Join Date: May 2012
Location: Anton, Texas
Posts: 2,364
|
Re: What did you do to your truck today? Chapter II
well the west Texas heat ,sun, and not much rain has taken a toll on old dollor's wood bed ....time to do something different . started sanding last night and will try and finish the prep work today , decided to go with a spray or roll in bed liner and see if that will last longer, living outside is hard on pickups. pic's will come later...Don
|
|
|
|
08-06-2014, 09:45 PM
|
#3 | |
|
Registered User
Join Date: Nov 2013
Location: Lubbock, TX
Posts: 283
|
Re: What did you do to your truck today? Chapter II
Quote:
 start cooling off.
__________________
"Now all I need is a shop to go with my shop vac!" 
|
|
|
|
|
08-06-2014, 03:53 PM
|
#4 |
|
Registered User
Join Date: Jun 2006
Location: Lutz, Florida
Posts: 838
|
Re: What did you do to your truck today? Chapter II
I charged up the Vintage Air in the 67 today!
__________________
1967 Red, C10 Short Bed 6.0L T5 5 speed 1967 Orange and Black C50 6.2 Detroit Diesel NV4500, 2 Ton Pickup 1972 White, Chevy Blazer 2WD 67 Dog house 5.3 4L65 2016 Power Tour LH 1955 Red-Cream, Chevrolet Nomad, restoration on hold 2004 Black, Corvette Z06 LS6 convertible (Rock solid Fun) 2011/2018 Power Tour |
|
|
|
08-06-2014, 07:56 PM
|
#5 |
|
Registered User
Join Date: Nov 2013
Location: Lubbock, TX
Posts: 283
|
Re: What did you do to your truck today? Chapter II
I figured it was time to repair the holes in the tailgate left by the PO. I heard that he backed up too far while attempting to hook to up his 5th wheel trailer & punched two identical holes in the tailgate. Believe it or not this was my first time to ever do any sheet metal repair in my lifetime. Not too bad for a rookie huh?
__________________
"Now all I need is a shop to go with my shop vac!"
|
|
|
|
08-07-2014, 01:49 PM
|
#6 |
|
Registered User
Join Date: Jun 2014
Location: Littleton
Posts: 41
|
Re: What did you do to your truck today? Chapter II
Oh god that funny^^^^^^^^^^^^^
Anyway, I painted my cab white and pulled the front bumper to do the same. 
|
|
|
|
08-08-2014, 04:39 PM
|
#7 |
|
Registered User
Join Date: Feb 2011
Location: Knoxville, TN
Posts: 362
|
Re: What did you do to your truck today? Chapter II
Finally got my exhaust manifolds stripped/cleaned and painted with Por-15 factory gray manifold paint.
|
|
|
|
08-09-2014, 04:15 PM
|
#8 |
|
Registered User
Join Date: Sep 2013
Location: Gonzales, La
Posts: 1,441
|
Re: What did you do to your truck today? Chapter II
Just changed the starter out on ol Samson.
__________________
MyToys: Goldilocks the "Ol School Survivor" 1968 C10, SWB Stepside, 08/15 TOTM, 250 CI 6 cylinder, 3 on the tree, 3.73 rear, 3/5 static drop, 23,500 original miles. Samson the 1970 CST10, LWB, 462Ci, Turbo 350 tranny, 3.08 rear gear, PB, PS, A/C, AM/FM, 2/4 Drop. Brutus the 1998 Camaro Z28, 33,500 original miles, LS1, 519 RWHP/497 RWTQ. Member of the Louisiana Classic Truck Club, LCTC Member of the Louisiana C10 Club Member of the Baton Rouge Drifters Car Club |
|
|
|
08-10-2014, 07:56 PM
|
#9 |
|
Registered User
Join Date: Sep 2010
Location: Winfield, Ks.
Posts: 4,162
|
Re: What did you do to your truck today? Chapter II
I worked on the Wheel Tubs today that I got... man these are rough... I can make them pretty though...
__________________
Dan Johnston... Owner of My Dad's- '67 Chevy C-20 Custom Camper Short Fleetside Pickup PAPA J And our newest addition a- '71 Chevy CST/10 Short Fleetside Pickup Haulin' SOLD Papa J's Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=612847 Haulin's Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=671130SOLD B Bears Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=744210 |
|
|
|
08-11-2014, 10:16 PM
|
#10 |
|
Registered User
Join Date: Jul 2012
Location: Rosenberg, Texas
Posts: 3,506
|
Re: What did you do to your truck today? Chapter II
Finished installing the bow tie in my new billet grille.
__________________
-Duane C/10 Club Texas member 1971 Chevy C10 "Brutus" SWB Fleetside 2016 6.0L (L96) 6L90E (driver/project) 1965 Pontiac GTO "Royal Goat" 400/TH400 w/AC (my baby) |
|
|
|
08-13-2014, 05:07 PM
|
#11 | |
|
Registered User
Join Date: Jun 2014
Location: illinois
Posts: 72
|
Re: What did you do to your truck today? Chapter II
Quote:
|
|
|
|
|
08-13-2014, 08:39 AM
|
#12 |
|
Registered User
Join Date: Oct 2011
Location: Houston tx
Posts: 701
|
Re: What did you do to your truck today? Chapter II
 Got this in the mail yesterday, hope to install it later this week |
|
|
|
08-13-2014, 08:47 AM
|
#13 |
|
Registered User
Join Date: Jun 2006
Location: Lutz, Florida
Posts: 838
|
Re: What did you do to your truck today? Chapter II
Got my drive shaft installed.
Now the C50 is back on the road, super singles and disk brakes in the back. Think the sway bar is big enough? Long bed installation is next after a little rear end cleanup. Then tackle finding a front axle with disk also!
__________________
1967 Red, C10 Short Bed 6.0L T5 5 speed 1967 Orange and Black C50 6.2 Detroit Diesel NV4500, 2 Ton Pickup 1972 White, Chevy Blazer 2WD 67 Dog house 5.3 4L65 2016 Power Tour LH 1955 Red-Cream, Chevrolet Nomad, restoration on hold 2004 Black, Corvette Z06 LS6 convertible (Rock solid Fun) 2011/2018 Power Tour |
|
|
|
08-13-2014, 11:56 AM
|
#14 | |
|
Registered User
Join Date: Oct 2012
Location: Rose Hill Kansas
Posts: 1,351
|
Re: What did you do to your truck today? Chapter II
Quote:
__________________
1970 C10 Short Stepper with 71/72 front clip. |
|
|
|
|
08-13-2014, 04:23 PM
|
#15 | |
|
Registered User
Join Date: Jun 2006
Location: Lutz, Florida
Posts: 838
|
Re: What did you do to your truck today? Chapter II
Quote:
__________________
1967 Red, C10 Short Bed 6.0L T5 5 speed 1967 Orange and Black C50 6.2 Detroit Diesel NV4500, 2 Ton Pickup 1972 White, Chevy Blazer 2WD 67 Dog house 5.3 4L65 2016 Power Tour LH 1955 Red-Cream, Chevrolet Nomad, restoration on hold 2004 Black, Corvette Z06 LS6 convertible (Rock solid Fun) 2011/2018 Power Tour |
|
|
|
|
08-14-2014, 04:15 PM
|
#16 |
|
Registered User
Join Date: Jun 2013
Location: billings, mt
Posts: 703
|
Re: What did you do to your truck today? Chapter II
those turned out nice!
__________________
1969 Chevy C10 2wd stepside longbox |
|
|
|
08-14-2014, 06:09 PM
|
#17 | |
|
Registered User
Join Date: Nov 2013
Location: Lubbock, TX
Posts: 283
|
Re: What did you do to your truck today? Chapter II
Quote:
__________________
"Now all I need is a shop to go with my shop vac!"
|
|
|
|
|
08-14-2014, 07:19 PM
|
#18 |
|
Registered User
Join Date: Oct 2012
Location: Rose Hill Kansas
Posts: 1,351
|
Re: What did you do to your truck today? Chapter II
Inventoried all of parts for my Vintage Air install.
__________________
1970 C10 Short Stepper with 71/72 front clip. |
|
|
|
08-14-2014, 07:20 PM
|
#19 |
|
Registered User
Join Date: Sep 2010
Location: Winfield, Ks.
Posts: 4,162
|
Re: What did you do to your truck today? Chapter II
Sweet!!!!
__________________
Dan Johnston... Owner of My Dad's- '67 Chevy C-20 Custom Camper Short Fleetside Pickup PAPA J And our newest addition a- '71 Chevy CST/10 Short Fleetside Pickup Haulin' SOLD Papa J's Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=612847 Haulin's Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=671130SOLD B Bears Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=744210 |
|
|
|
08-14-2014, 08:00 PM
|
#20 |
|
Registered User
Join Date: Sep 2013
Location: Evansville, IN
Posts: 1,774
|
Re: What did you do to your truck today? Chapter II
Tired of seeing the truck sitting in the garage and not being driven. Snapped a couple wheel studs a month or so ago so tonight I'm fixing that. 5 new wheel studs and an exhaust patch where I ripped a hole in it backing it off the trailer.
__________________
Ryan 1967 Red Stepside..."Laymond" http://67-72chevytrucks.com/vboard/s...40#post6441840 1972 Medium Olive SWB-Chester http://67-72chevytrucks.com/vboard/s...d.php?t=759628 1967/71 Blue SWB C10..SOLD 1977 SWB K10..my grandpa's.....never should have sold |
|
|
|
08-14-2014, 10:18 PM
|
#21 |
|
Registered User
Join Date: Jul 2014
Location: Memphis, TN
Posts: 67
|
Re: What did you do to your truck today? Chapter II
New shocks, springs and tank relocated.... ran into a few glitches but parts are on the way.
|
|
|
|
08-15-2014, 02:22 AM
|
#22 |
|
Registered User
Join Date: Jun 2013
Location: billings, mt
Posts: 703
|
Re: What did you do to your truck today? Chapter II
Took her out to the weekly cruise, usually I hide in back but this time I found this big beauty to hide behind! don't know who's it is but it is one really nice truck! now if Daman would have been there he could blocked me from the other side! there was also I really nice 67/68 patina truck but he took off before I got a pic.
__________________
1969 Chevy C10 2wd stepside longbox |
|
|
|
08-18-2014, 05:03 PM
|
#23 | |
|
Registered User
Join Date: Aug 2014
Location: Vernal, UT
Posts: 47
|
Re: What did you do to your truck today? Chapter II
Quote:
__________________
1968 C10, 327 large journal crank, TH400 trans, 12 bolt 3.73 geared rear axle, and rear leaf springs. HEI, Delco 10SI, and brake booster upgrades. Formerly known as mtndewmaniac66. |
|
|
|
|
08-18-2014, 07:16 PM
|
#24 |
|
Registered User
Join Date: Jun 2011
Location: Sunbury, N.C
Posts: 140
|
Re: What did you do to your truck today? Chapter II
Had the rims powdercoated and put new rubber on.
|
|
|
|
08-15-2014, 08:44 AM
|
#25 |
|
Registered User
Join Date: Aug 2014
Location: Huntley,Illinois
Posts: 21
|
Re: What did you do to your truck today? Chapter II
Yesterday I popped out 2 lower ball joints and one upper ball joint. Today Im finishing the other one and then to get the A arms prepped for sandblasting!
|
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
