What did you do to your truck today??

[KQQL IT]

Recently got my son a 90 Cheyenne regular cab shorty.
Been doing the usual ignition brakes oil grease tuneup.

Tried to get the axle out for passenger side axle seal and as usual it seems the spider gear pin was broken.
Easy Sunday got long.

[special-K]

Nice project. I'd like to find one something like that.

[KQQL IT]

1990s eagles off

1980 something rally wheels on and some 275 60 coopers

[Palf70Step]

Ralleys always look great on these trucks.

[KQQL IT]

We finally got a brake pedal!
Adjuster nuts where on backwards from the prior owner. :/

And 3 new brake hoses
New shoes pads re packed wheel bearings idler and pitman arms.
Maybe now I'll feel good about my son driving this one.

[Just call me Sean]

I took the good spare from my van and put it on the truck, so I would still have the not so great spare on the front. It was pretty bald, but I didn't notice until today that the belts were starting to poke through the center because leaves were sticking to the sharp points. It will be the van spare until I get another tire. Also, the 99 is down until I figure out what's wrong with it.

[KQQL IT]

Oil and filter
pcv valve
grommet and vacuum tube.
Seems to have fixed our low idle issue.
Hope so.

[Just call me Sean]

On the 93, the idler pulley locked up. The belt unscrewed it from the bracket and threw it off the engine and got chopped up in the process. After searching the ground where it happened I found the pulley laying on the frame rail under the hood. Purchased a new belt and pulley and then realized I had to go to the junkyard to get another bolt and spacer because they were damaged too.

[Just call me Sean]

I went back to the junkyard and picked up my 88-89 headlight upgrade/downgrade. I saw them yesterday when I was getting my repair parts. Cost me $30.

[KQQL IT]

New gm mini 337-1022 starter and a manual oil pressure gauge.
30 psi idle good enough for 160k sbc as the dash says 15psi and drops to zero hot idle.

[Just call me Sean]

I disassembled the headlights so I can clean everything up and repaint the rings and buckets black. I saw someone had changed the headlights and didn't put the rings on right, and I also noticed one side had the buckets reversed.

[Just call me Sean]

I'm trying two different rust treatments on the buckets, both are very old. I've had them a long time. They might not even be good anymore.

[attack eagle]

I spent 4 hours yesterday trying to get the dang 02 sensor off. Tried every trick I know, heat and quench, pipe over a socket, breaker bar, 02 socket amd 02 crows foot socket, jack under end of breaker bar, etc.


Came to the conclusion that what I really need is to get it on the air so I can pull down on a breaker bar and get 90-150 degrees of movement instead of only 45ish but since no lift, no can do. Will have to take it to a shop unfortunately. It does drive better with the 02 unplugged so that gives me hope that the 02 was failed all along.


Last week I installed the amps and iDQ sub, for about 2 weeks in march I had it completely apart installing new carpet and color matching all the trim plastics to Lt neutral and deleting 30 years worth of PO add on wiring.

[Just call me Sean]

Originally Posted by attack eagle

I spent 4 hours yesterday trying to get the dang 02 sensor off. Tried every trick I know, heat and quench, pipe over a socket, breaker bar, 02 socket amd 02 crows foot socket, jack under end of breaker bar, etc.


Came to the conclusion that what I really need is to get it on the air so I can pull down on a breaker bar and get 90-150 degrees of movement instead of only 45ish but since no lift, no can do. Will have to take it to a shop unfortunately. It does drive better with the 02 unplugged so that gives me hope that the 02 was failed all along.


Last week I installed the amps and iDQ sub, for about 2 weeks in march I had it completely apart installing new carpet and color matching all the trim plastics to Lt neutral and deleting 30 years worth of PO add on wiring.

Are you left handed? You take pictures like a lefty, that's why they're upside down.

[Palf70Step]

Originally Posted by attack eagle

I spent 4 hours yesterday trying to get the dang 02 sensor off. Tried every trick I know, heat and quench, pipe over a socket, breaker bar, 02 socket amd 02 crows foot socket, jack under end of breaker bar, etc.


Came to the conclusion that what I really need is to get it on the air so I can pull down on a breaker bar and get 90-150 degrees of movement instead of only 45ish but since no lift, no can do. Will have to take it to a shop unfortunately. It does drive better with the 02 unplugged so that gives me hope that the 02 was failed all along.


Last week I installed the amps and iDQ sub, for about 2 weeks in march I had it completely apart installing new carpet and color matching all the trim plastics to Lt neutral and deleting 30 years worth of PO add on wiring.

Fixed ur pictures for ya

[Just call me Sean]

So after it sitting for almost three weeks, I've started trying to figure out what's wrong with the 99 again. I had cleared the codes, when I do that it runs pretty well until it sets the codes again. The codes are P0339 and the problem should revolve around that as the other is P0341 which is said to trigger because of the P0339. When they set it runs awful, misfiring and lack of power. I hooked a voltmeter to the crank signal wire and it's working fine right now, steady at about 6 volts. Hasn't set the codes again yet, I guess I'll have to drive it around some more. It also cranks slow when starting, like it may have jumped time. I might end up pulling the timing cover to inspect, after I get it to run rough again.

[Just call me Sean]

I worked on cleaning up the headlight buckets. I think it's interesting that all four are different, not just lefts and rights. At first I wasn't too impressed with the treatments I used. I wire brushed them as clean as I could then hit them with a third treatment I had. That one seemed good, it was burning my hands while I was using it. Maybe next time I'll use gloves. Then I noticed the naval jelly removed the paint too, I don't know why I didn't see it sooner. I'm thinking about stripping the other three also but I don't think it's really going to matter.

[Just call me Sean]

I sprayed the buckets. Ran out of paint. Will have to get more for the rings and I want to put another coat on the face of the buckets.

[Just call me Sean]

I stripped and painted the rings. Next is the screws and springs. Everything else is plastic and stainless steel so they will just need a good cleaning.

[Just call me Sean]

I cleaned and dipped the screws but I have the springs submerged. I'm not sure how long I should leave them in there, you can see it dissolving the rust.

[Just call me Sean]

I painted the screws and springs and gave the buckets another coat. I'll let everything dry until Saturday and reassemble then.

[Just call me Sean]

Since my tire carrier was originally mounted sideways on a van door and I modified it to up and down, it isn't as strong and has started to sag. The tire rubs on it which weakens the sidewall. I bent it back up and added a brace. I also spaced the tire out more for more clearance. I'll have to modify the lock because it doesn't fit anymore since I changed the spacing.

[Just call me Sean]

I started reassembly of the headlights with some difficulty. The buckets I thought were backwards weren't, they were that way because the headlights have a little tab for some reason and it interferes with the screw side. Having the screws on that side makes changing the low beam headlight more difficult as the screws are beneath a plastic piece when positioned that way. I decided to cut off the tab for the two headlights. Not too bad for the new low beam, the tab is metal, but the old high beams which I'm reusing the tab is glass. A cutoff wheel on my Dremel took off the metal one and I also used it to score the glass one and snapped it off then smoothed it. You can see the glass tab I didn't remove on the bottom lower right side.

[LUV2XCLR8]

Got my Center caps in for Old School Shoes.

I went pretty short on the fronts, since I am
running spikes I did not want a bulky cap...

[Just call me Sean]

Headlight swap is done. I can already tell they're brighter. Working on the tire carrier so I can get it back on.