Ok Boys and Girls it's Storytime - Page 37 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**regan wilson** · 02-13-2022, 09:29 AM

Fridays progress. Somehow my intake pushrods are still too long. The adjusters are almost topped out and that restricts the oiling of the trunnion and the tip. I'll find out how well it oils today when I prime it. I bench tested them with air and solvent. I think it will make one race then send the intakes back again.

A.Delaney · 02-13-2022, 08:56 PM

Quote:

Originally Posted by regan wilson

Fridays progress. Somehow my intake pushrods are still too long. The adjusters are almost topped out and that restricts the oiling of the trunnion and the tip. I'll find out how well it oils today when I prime it. I bench tested them with air and solvent. I think it will make one race then send the intakes back again.

Those are some massive intake ports!

**regan wilson** · 02-15-2022, 08:51 AM

Quote:

Originally Posted by A.Delaney

Those are some massive intake ports!

Yes Sir! I can stick four fingers high in them.

**regan wilson** · 02-13-2022, 09:31 AM

Yesterdays progress. Ken showed up in time to help stick the motor in. Still a bunch of work to do today. Hopefully I'll get it fired this afternoon.

SCOTI · 02-13-2022, 02:28 PM

The push rod issue.... Is that a thing were you have to check multiples to ID the issue or an anomaly?

**regan wilson** · 02-15-2022, 08:49 AM

Quote:

Originally Posted by SCOTI

The push rod issue.... Is that a thing were you have to check multiples to ID the issue or an anomaly?

There are three different length pushrods. Two different intake and then the exhaust. It may have been the cut up pushrod that caused me to miss it on the length. It may have had a smaller od end on it than my pushrods. The seat was higher in the new lifters. It threw everything off.

**regan wilson** · 02-15-2022, 08:56 AM

We got it running Sunday evening. I was in the shop from 8am till 7pm. I should have quit at 5pm. I had a little hiccup and chunked a pushrod. I think everything is going to be ok though. My new alternator belts were too short but I'll have some more tomorrow. Chrome don't get you home but some newly added stainless hardware cleans everything up a little.

**mongocanfly** · 02-15-2022, 05:56 PM

It's a beaut to look at,,,,no matter what

**regan wilson** · 02-15-2022, 09:55 PM

Quote:

Originally Posted by mongocanfly

It's a beaut to look at,,,,no matter what

Thank You Bud!

**regan wilson** · 02-16-2022, 08:28 AM

When we got the truck running I wasn't showing any fuel pressure. I've been messing with it the last two days. I finally had to pull the cluster. Like I haven't had it out enough times this winter. I loosened the isolator line at the bottom and bulbed antifreeze into it and capped it off. Luckily it's working now. I didn't know if it was the gauge or my pump .The way my luck has run lately I wouldn't doubt I had a pump issue.

**regan wilson** · 02-16-2022, 09:18 PM

My new belts were here when I got home today. Luckily everything worked out. I only had 10.25" to 10.75" of centerline to work with on belt size. Andrew at Jones Racing Products sent me the right belt. They have to calculate the tooth count on both pulleys and the centerline to get the right length.

SCOTI · 02-16-2022, 09:21 PM

Where's the debut on the freshened mill?

**regan wilson** · 02-16-2022, 09:49 PM

Quote:

Originally Posted by SCOTI

Where's the debut on the freshened mill?

Next week in Belle Rose, La. We'll get it finished up and loaded this weekend.

SCOTI · 02-16-2022, 11:26 PM

Thanks.

It was probably mentioned but when I went back to look I just missed it.
I'll be on the look-out when you're closer to home.

**regan wilson** · 02-17-2022, 08:44 AM

Quote:

Originally Posted by SCOTI

Thanks.

It was probably mentioned but when I went back to look I just missed it.
I'll be on the look-out when you're closer to home.

Tx Motorplex May 19th to the 22nd.

**regan wilson** · 02-19-2022, 08:20 PM

**regan wilson** · 02-19-2022, 08:21 PM

Dirty but ready to go!

**regan wilson** · 02-19-2022, 08:23 PM

Flat Hoods are cool!

SCOTI · 02-20-2022, 12:59 AM

Sweet! Looks clean enuff for the task.
Go get-em!

**regan wilson** · 02-21-2022, 09:12 AM

Quote:

Originally Posted by SCOTI

Sweet! Looks clean enuff for the task.
Go get-em!

Thanks Scoti. As I said it would probably be down to the wire on getting ready. It's in the box and ready to go.

**mongocanfly** · 02-21-2022, 02:36 PM

boxed up...just needs a ribbon on it..!!!

**regan wilson** · 02-22-2022, 09:53 AM

Quote:

Originally Posted by mongocanfly

boxed up...just needs a ribbon on it..!!!

It needs to bring home a Wally and a Paycheck.

**regan wilson** · 02-22-2022, 09:55 AM

On another note. Mongo nominated me for TOTM this month. Vote now vote often! Lol

***Liz*** · 02-22-2022, 10:00 AM

Quote:

Originally Posted by regan wilson

On another note. Mongo nominated me for TOTM this month. Vote now vote often! Lol

well deserved imho

**regan wilson** · 02-22-2022, 10:04 AM

Quote:

Originally Posted by Liz

well deserved imho

Thank you Liz.

02-13-2022, 09:29 AM	#1
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime Fridays progress. Somehow my intake pushrods are still too long. The adjusters are almost topped out and that restricts the oiling of the trunnion and the tip. I'll find out how well it oils today when I prime it. I bench tested them with air and solvent. I think it will make one race then send the intakes back again. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

02-13-2022, 09:31 AM	#4
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime Yesterdays progress. Ken showed up in time to help stick the motor in. Still a bunch of work to do today. Hopefully I'll get it fired this afternoon. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

02-13-2022, 02:28 PM	#5
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,028	Re: Ok Boys and Girls it's Storytime The push rod issue.... Is that a thing were you have to check multiples to ID the issue or an anomaly? __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

02-15-2022, 08:56 AM	#7
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime We got it running Sunday evening. I was in the shop from 8am till 7pm. I should have quit at 5pm. I had a little hiccup and chunked a pushrod. I think everything is going to be ok though. My new alternator belts were too short but I'll have some more tomorrow. Chrome don't get you home but some newly added stainless hardware cleans everything up a little. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

02-15-2022, 05:56 PM	#8
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,662	Re: Ok Boys and Girls it's Storytime It's a beaut to look at,,,,no matter what __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver

02-16-2022, 08:28 AM	#10
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime When we got the truck running I wasn't showing any fuel pressure. I've been messing with it the last two days. I finally had to pull the cluster. Like I haven't had it out enough times this winter. I loosened the isolator line at the bottom and bulbed antifreeze into it and capped it off. Luckily it's working now. I didn't know if it was the gauge or my pump .The way my luck has run lately I wouldn't doubt I had a pump issue. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

02-16-2022, 09:18 PM	#11
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime My new belts were here when I got home today. Luckily everything worked out. I only had 10.25" to 10.75" of centerline to work with on belt size. Andrew at Jones Racing Products sent me the right belt. They have to calculate the tooth count on both pulleys and the centerline to get the right length. __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

02-16-2022, 09:21 PM	#12
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,028	Re: Ok Boys and Girls it's Storytime Where's the debut on the freshened mill? __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

02-16-2022, 11:26 PM	#14
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,028	Re: Ok Boys and Girls it's Storytime Thanks. It was probably mentioned but when I went back to look I just missed it. I'll be on the look-out when you're closer to home. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

02-19-2022, 08:20 PM	#16
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

02-19-2022, 08:21 PM	#17
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime Dirty but ready to go! __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

02-19-2022, 08:23 PM	#18
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime Flat Hoods are cool! __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph

02-20-2022, 12:59 AM	#19
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,028	Re: Ok Boys and Girls it's Storytime Sweet! Looks clean enuff for the task. Go get-em! __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

02-21-2022, 02:36 PM	#21
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,662	Re: Ok Boys and Girls it's Storytime boxed up...just needs a ribbon on it..!!! __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver

02-22-2022, 09:55 AM	#23
regan wilson Senior Member Join Date: Mar 2008 Location: tyler texas Posts: 1,537	Re: Ok Boys and Girls it's Storytime On another note. Mongo nominated me for TOTM this month. Vote now vote often! Lol __________________ NHRA Super Street 469C It only runs 10.90 at 156 mph



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.