What did you do to your truck today? Chapter II - Page 37 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

OregonNed · 07-15-2014, 11:57 PM

Quote:

Originally Posted by Ekliptix

Washed it and had a new seat cover installed.

Nice truck! Looking awesome!

Motoxrrar · 07-16-2014, 03:48 AM

Rear end powder coated, back under the truck.
New griffin ls swap radiator.
Found a spot for my ECM

Motoxrrar · 07-16-2014, 03:50 AM

Griffin ls swap radiator, thanks summit!!

Motoxrrar · 07-16-2014, 03:54 AM

Rear end rebuilt, 354 gears now!
Thanks to Yukon I finally got the gear set right.
Must have tool!!

Motoxrrar · 07-16-2014, 04:02 AM

Found a spot for my ECM
Made a bracket from stainless,
using the emergency brake studs.
Fits nicely.
More pics tomorrow after I'm done tig welding it.

R.L. · 07-16-2014, 09:32 PM

Picked up a swaybar and the hardware going to do the install tomorrow, tonight I think I'm going to drive down to the island in her and do some fishing.

bshepherd1 · 07-16-2014, 10:02 PM

Drove her for the first time ever working out the bugs

Turbo1dr · 07-16-2014, 10:40 PM

I put tags and insurance on it. Getting ready to work out the bugs too.

R.L. · 07-17-2014, 11:35 AM

Installed the sway bar I picked up yesterday, haven't been on the highway yet but around the neighborhood it's a completely different animal!

jtwells · 07-20-2014, 05:31 PM

Knocked the 2 rear cross members out to make way for the new PB ones that should come in any week now. If you are planning on doing this I suggest find a better method then a 4 lb hammer and a set of punches and chisels... I'm sure my arms will be sore for another 2 days.

Motoxrrar · 07-20-2014, 05:44 PM

Quote:

Originally Posted by jtwells

Knocked the 2 rear cross members out to make way for the new PB ones that should come in any week now. If you are planning on doing this I suggest find a better method then a 4 lb hammer and a set of punches and chisels... I'm sure my arms will be sore for another 2 days.

You got it easy!!! I did mine with the bed and can on. But a sanding disc for an angle grinder and a good drill bit makes those super easy. I just used a sanding disc to grind the head flush and then drilled them out. No hammers necessary

**Elliot949** · 07-20-2014, 05:47 PM

I attempted to properly assemble my bed today only to find out the Head Panel is improperly made... there is 5/16" difference in the height of it from the 19 3/4" on the right side (correct Measurement) to 20 1/16" on the left side which does not allow the Bedside to sit gown properly on the floor... I will call the supplier tomorrow and see about getting a replacement...

casper1969 · 07-20-2014, 06:57 PM

Well Friday I installed new sport bumper, finally got the old boat anchor step'n'toe off. then Saturday took to body shop for paint 12 years in the waiting

sorry guys do not know how to post pictures

**Elliot949** · 07-20-2014, 07:03 PM

Quote:

Originally Posted by casper1969

Well Friday I installed new sport bumper, finally got the old boat anchor step'n'toe off. then Saturday took to body shop for paint 12 years in the waiting

sorry guys do not know how to post pictures

To post a pic just click on the Advance post then scoll to the Manage Attachments a box will pop up and look where it says Browse... Once you click on the pic and it goes into the box click on Upload then close the box and click on post... It is really pretty simple...

**Grumpy old man** · 07-20-2014, 07:34 PM

Still buying parts !

74baggedbug · 07-20-2014, 07:41 PM

Installed new front Monroe shocks and boy is it a huge difference.. Tomorrow I slap in the rears

casper1969 · 07-20-2014, 07:47 PM

Thanks Elliot

**Elliot949** · 07-20-2014, 07:52 PM

Sweet!!!!

casper1969 · 07-20-2014, 07:53 PM

Here are some other things i've done as of recent that i wasn't to show pics and now i can
modified modern center caps for my american racing wheels
installed rear sway bar from CCP
and rebuilt and installed tilt column from 71 chevy truck

casper1969 · 07-20-2014, 08:02 PM

last month i installed a from valance from a 91 chevy 2wd truck just about bolts right up with the exception og a self tapping screw on each end at inner fender
I am very pleased with outcome looks almost factory

R.L. · 07-20-2014, 09:07 PM

Finally fixed my rattling tail gate and pulled the wire for my interior light.

3drburb · 07-20-2014, 09:21 PM

Did some work on the interior and added a chrome front bumper.

UNEASYRIDER · 07-20-2014, 11:14 PM

Sprayed some hot rod black

Turbo1dr · 07-20-2014, 11:19 PM

Quote:

Originally Posted by UNEASYRIDER

Sprayed some hot rod black

I love that color!

69chevytrucker · 07-20-2014, 11:33 PM

tried my hand at so stripes today
Name: IMG1609.jpg
Views: 683
Size: 50.7 KB

Name: IMG1608.jpg
Views: 681
Size: 54.7 KB

Name: IMG1607.jpg
Views: 677
Size: 51.6 KB

Name: IMG1604.jpg
Views: 674
Size: 69.0 KB

Name: IMG1605.jpg
Views: 681
Size: 62.5 KB

plan to find some skull and crossbone lace to put over and mist some silver over it

07-16-2014, 03:48 AM	#902
Motoxrrar Registered User Join Date: Feb 2014 Location: Tennessee Posts: 282	Re: What did you do to your truck today? Chapter II Rear end powder coated, back under the truck. New griffin ls swap radiator. Found a spot for my ECM Attached Images

07-16-2014, 03:50 AM	#903
Motoxrrar Registered User Join Date: Feb 2014 Location: Tennessee Posts: 282	Re: What did you do to your truck today? Chapter II Griffin ls swap radiator, thanks summit!! Attached Images

07-16-2014, 03:54 AM	#904
Motoxrrar Registered User Join Date: Feb 2014 Location: Tennessee Posts: 282	Re: What did you do to your truck today? Chapter II Rear end rebuilt, 354 gears now! Thanks to Yukon I finally got the gear set right. Must have tool!! Attached Images

07-16-2014, 04:02 AM	#905
Motoxrrar Registered User Join Date: Feb 2014 Location: Tennessee Posts: 282	Re: What did you do to your truck today? Chapter II Found a spot for my ECM Made a bracket from stainless, using the emergency brake studs. Fits nicely. More pics tomorrow after I'm done tig welding it. Attached Images

07-16-2014, 09:32 PM	#906
R.L. Registered User Join Date: Sep 2008 Location: Mobile, Al. Posts: 687	Re: What did you do to your truck today? Chapter II Picked up a swaybar and the hardware going to do the install tomorrow, tonight I think I'm going to drive down to the island in her and do some fishing.

07-16-2014, 10:02 PM	#907
bshepherd1 Registered User Join Date: Dec 2013 Location: Addison Michigan Posts: 17	Re: What did you do to your truck today? Chapter II Drove her for the first time ever working out the bugs

07-16-2014, 10:40 PM	#908
Turbo1dr Registered User Join Date: Jun 2014 Location: New Bern, NC Posts: 177	Re: What did you do to your truck today? Chapter II I put tags and insurance on it. Getting ready to work out the bugs too. __________________ 1971 Cheyenne Super - Factory Big Block - Second (1987-89) & Fourth (2014-) Owner - To be restored 1978 Turbo Malibu - Owned since 1986 1987 Grand National Aerocoupe -1 of 1 1988 LeSabre T-Type - Supercharged

07-17-2014, 11:35 AM	#909
R.L. Registered User Join Date: Sep 2008 Location: Mobile, Al. Posts: 687	Re: What did you do to your truck today? Chapter II Installed the sway bar I picked up yesterday, haven't been on the highway yet but around the neighborhood it's a completely different animal!

07-20-2014, 05:31 PM	#910
jtwells Registered User Join Date: Apr 2014 Location: MD Posts: 26	Re: What did you do to your truck today? Chapter II Knocked the 2 rear cross members out to make way for the new PB ones that should come in any week now. If you are planning on doing this I suggest find a better method then a 4 lb hammer and a set of punches and chisels... I'm sure my arms will be sore for another 2 days. Attached Images

07-20-2014, 05:47 PM	#912
Elliot949 Registered User Join Date: Sep 2010 Location: Winfield, Ks. Posts: 4,162	Re: What did you do to your truck today? Chapter II I attempted to properly assemble my bed today only to find out the Head Panel is improperly made... there is 5/16" difference in the height of it from the 19 3/4" on the right side (correct Measurement) to 20 1/16" on the left side which does not allow the Bedside to sit gown properly on the floor... I will call the supplier tomorrow and see about getting a replacement... __________________ Dan Johnston... Owner of My Dad's- '67 Chevy C-20 Custom Camper Short Fleetside Pickup PAPA J And our newest addition a- '71 Chevy CST/10 Short Fleetside Pickup Haulin' SOLD Papa J's Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=612847 Haulin's Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=671130SOLD B Bears Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=744210

07-20-2014, 06:57 PM	#913
casper1969 Registered User Join Date: Sep 2012 Location: Sabattus,Maine Posts: 38	Re: What did you do to your truck today? Chapter II Well Friday I installed new sport bumper, finally got the old boat anchor step'n'toe off. then Saturday took to body shop for paint 12 years in the waiting sorry guys do not know how to post pictures

07-20-2014, 07:34 PM	#915
Grumpy old man Senior Member Join Date: Dec 2013 Location: Gods country East,Tn Posts: 8,545	Re: What did you do to your truck today? Chapter II Still buying parts !

07-20-2014, 07:41 PM	#916
74baggedbug Registered User Join Date: Oct 2011 Location: Houston tx Posts: 701	Re: What did you do to your truck today? Chapter II Installed new front Monroe shocks and boy is it a huge difference.. Tomorrow I slap in the rears

07-20-2014, 07:47 PM	#917
casper1969 Registered User Join Date: Sep 2012 Location: Sabattus,Maine Posts: 38	Re: What did you do to your truck today? Chapter II Thanks Elliot Attached Images

07-20-2014, 07:52 PM	#918
Elliot949 Registered User Join Date: Sep 2010 Location: Winfield, Ks. Posts: 4,162	Re: What did you do to your truck today? Chapter II Sweet!!!! __________________ Dan Johnston... Owner of My Dad's- '67 Chevy C-20 Custom Camper Short Fleetside Pickup PAPA J And our newest addition a- '71 Chevy CST/10 Short Fleetside Pickup Haulin' SOLD Papa J's Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=612847 Haulin's Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=671130SOLD B Bears Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=744210



Register or Log In To remove these advertisements.

07-20-2014, 07:53 PM	#919
casper1969 Registered User Join Date: Sep 2012 Location: Sabattus,Maine Posts: 38	Re: What did you do to your truck today? Chapter II Here are some other things i've done as of recent that i wasn't to show pics and now i can modified modern center caps for my american racing wheels installed rear sway bar from CCP and rebuilt and installed tilt column from 71 chevy truck Attached Images

07-20-2014, 08:02 PM	#920
casper1969 Registered User Join Date: Sep 2012 Location: Sabattus,Maine Posts: 38	Re: What did you do to your truck today? Chapter II last month i installed a from valance from a 91 chevy 2wd truck just about bolts right up with the exception og a self tapping screw on each end at inner fender I am very pleased with outcome looks almost factory Attached Images

07-20-2014, 09:07 PM	#921
R.L. Registered User Join Date: Sep 2008 Location: Mobile, Al. Posts: 687	Re: What did you do to your truck today? Chapter II Finally fixed my rattling tail gate and pulled the wire for my interior light.

07-20-2014, 09:21 PM	#922
3drburb Registered User Join Date: Jul 2011 Location: Kent, WA. Posts: 848	Re: What did you do to your truck today? Chapter II Did some work on the interior and added a chrome front bumper. Attached Images

07-20-2014, 11:14 PM	#923
UNEASYRIDER Registered User Join Date: Apr 2009 Location: PHOENIX,ARIZONA Posts: 91	Re: What did you do to your truck today? Chapter II Sprayed some hot rod black Attached Images __________________ DON'T BUILD IT IF YOUR NOT GONA DRIVE IT!!

07-20-2014, 11:33 PM	#925
69chevytrucker Registered User Join Date: Apr 2014 Location: calgary alberta Posts: 1,248	Re: What did you do to your truck today? Chapter II tried my hand at so stripes today plan to find some skull and crossbone lace to put over and mist some silver over it

Register or Log In To remove these advertisements.