The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1960 - 1966 Chevrolet & GMC Pickups Message Board > projects and builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 08-11-2014, 06:50 PM   #76
Modges'66
Registered User
 
Modges'66's Avatar
 
Join Date: Feb 2012
Location: Grand Rapids, Michigan, otherwise known as Beer City U.S.A.
Posts: 1,081
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Hey Chris!
Things are looking good!
I don't know if you noticed in my thread, but I had a similar problem with my roof and the tin-canning effect....Funny thing, but I never noticed until I thought that I had it ALL fixed, that the driver's side rear roof & drip-rail were pushed down about 3/8" from the opposite side.
Needless to say, total re-work with a sledge-hammer, and a body contoured 2"X12" placed strategically under the rear ledge of the roof fixed that, and also took care of all of the plastic work that I had labored so hard on!!!

Oh, and I would like to make a correction to your post that shows the door-jamb work:
GM had plenty of spot-welds, but on my cab, the only sign of seam sealer was in the rain-gutter.
I must have spent $200 on epoxy seam sealer doing the door-jambs, doors, rain-gutter, cowl & firewall.
As far as spot-welds go, the dash on the passenger-side had a boat-load of attempted welds along the lower windshield, & cowl that never took!
The dash & glovebox must have rattled like hell!!!! LOL!
Probably one of the reasons that mine is so rust free, nobody could stand to drive it!!!
All of that is fixed now!
Modges'66 is offline   Reply With Quote
Old 08-12-2014, 09:04 AM   #77
severedchris
Registered User
 
severedchris's Avatar
 
Join Date: May 2012
Location: Franklinton, LA
Posts: 179
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Quote:
Originally Posted by Modges'66 View Post
Hey Chris!
Things are looking good!
I don't know if you noticed in my thread, but I had a similar problem with my roof and the tin-canning effect....Funny thing, but I never noticed until I thought that I had it ALL fixed, that the driver's side rear roof & drip-rail were pushed down about 3/8" from the opposite side.
Needless to say, total re-work with a sledge-hammer, and a body contoured 2"X12" placed strategically under the rear ledge of the roof fixed that, and also took care of all of the plastic work that I had labored so hard on!!!

Oh, and I would like to make a correction to your post that shows the door-jamb work:
GM had plenty of spot-welds, but on my cab, the only sign of seam sealer was in the rain-gutter.
I must have spent $200 on epoxy seam sealer doing the door-jambs, doors, rain-gutter, cowl & firewall.
As far as spot-welds go, the dash on the passenger-side had a boat-load of attempted welds along the lower windshield, & cowl that never took!
The dash & glovebox must have rattled like hell!!!! LOL!
Probably one of the reasons that mine is so rust free, nobody could stand to drive it!!!
All of that is fixed now!

Thanks brutha, yeah that roof was no walk in the park.....lol. I did notice that in your thread, I spent about two hours reading through your whole thread the other day. Sick build by the way!!!!!! Our fix was about a million studs and a ton of pullin, but its worked out now. I just assumed about the seam sealer because mine had it all in the jams and all over the floor before I had it blasted. Someone before me must have thought it needed it.
__________________
"The objective is not to die for my country, but to provide the other poor bastard the opportunity to die for his!!!!"
severedchris is offline   Reply With Quote
Old 08-12-2014, 06:36 PM   #78
severedchris
Registered User
 
severedchris's Avatar
 
Join Date: May 2012
Location: Franklinton, LA
Posts: 179
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

The guys at the shop are moving right along on the bodywork...the passenger side needed a good bit of work.





My wiring kit came in from American Autowire....super nice stuff

__________________
"The objective is not to die for my country, but to provide the other poor bastard the opportunity to die for his!!!!"
severedchris is offline   Reply With Quote
Old 08-28-2014, 03:50 PM   #79
severedchris
Registered User
 
severedchris's Avatar
 
Join Date: May 2012
Location: Franklinton, LA
Posts: 179
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

The guys at the shop are really kicking butt these past few weeks

The start of a smooth firewall


Wheels and tires came in, got the Nitto 420s mounted up...love the tread pattern on these. Rear wheels don't quite fit though so we have to widen the tubs and narrow the rear end


Here's a measurement of the original style tubs.


A measurement on the new tubs we welded in


One more
__________________
"The objective is not to die for my country, but to provide the other poor bastard the opportunity to die for his!!!!"
severedchris is offline   Reply With Quote
Old 08-28-2014, 08:39 PM   #80
rwade
Registered User
 
rwade's Avatar
 
Join Date: Apr 2010
Location: Louisiana
Posts: 970
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Love those wheels man. I hope to see this one at last resort?! Looking good

Wade
rwade is offline   Reply With Quote
Old 08-28-2014, 09:06 PM   #81
Modges'66
Registered User
 
Modges'66's Avatar
 
Join Date: Feb 2012
Location: Grand Rapids, Michigan, otherwise known as Beer City U.S.A.
Posts: 1,081
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Chris,
The tubs still look kinda narrow...What wheel/tire width are you runnin on the rear?
Is your tire gonna go outside of the inner box-sides?
My tub is 13-1/2" wide & I have only about a 1/2" of clearance between the tire and the inner side of the tub with 315's, but the outer is also inside of the box-side.
Your wheels look awesome by the way!
I probably would have went with that style of wheel if I could have got the width & backspacing that I needed....Definitely sweet!
Modges'66 is offline   Reply With Quote
Old 09-02-2014, 10:39 AM   #82
severedchris
Registered User
 
severedchris's Avatar
 
Join Date: May 2012
Location: Franklinton, LA
Posts: 179
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Quote:
Originally Posted by rwade View Post
Love those wheels man. I hope to see this one at last resort?! Looking good

Not sure if I'll bring it to Last Resort as that is so close to SEMA...but we'll see...thanks dude

Wade
Quote:
Originally Posted by Modges'66 View Post
Chris,
The tubs still look kinda narrow...What wheel/tire width are you runnin on the rear?
Is your tire gonna go outside of the inner box-sides?
My tub is 13-1/2" wide & I have only about a 1/2" of clearance between the tire and the inner side of the tub with 315's, but the outer is also inside of the box-side.
Your wheels look awesome by the way!
I probably would have went with that style of wheel if I could have got the width & backspacing that I needed....Definitely sweet!
Modge...I have 13" between the outside of the bed and the inner part of the tub...and my measurement from outside edge to outside edge on my tires is 11.25", so itll be close but the dude narrowing the rearend is a machinist so hopefully he is precise....thanks for the compliments
__________________
"The objective is not to die for my country, but to provide the other poor bastard the opportunity to die for his!!!!"
severedchris is offline   Reply With Quote
Old 09-02-2014, 07:28 PM   #83
Modges'66
Registered User
 
Modges'66's Avatar
 
Join Date: Feb 2012
Location: Grand Rapids, Michigan, otherwise known as Beer City U.S.A.
Posts: 1,081
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Chris, my wheel is 11.5" wide which makes it 12.5" wide across the outside, and my tubs are 13.5 wide across the inside...Add to this the fact that my rear-end is all fresh and I didn't want to re-address it, or the costs of buying new axles...again!
My wheels are spaced to be within the INNER box side and the tub...
I didn't want the possibility of the return lip on the tub to ever come in contact with the tire, and I am running stock bed height/tub configuration (except for width).
I decided that is was a better choice to pay a little extra to buy a custom offset wheel to get the width & backspacing that I needed than to narrow the rear-end, and Travis at Pro-Performance really pulled this off for me!
Either way, the placement of the wheel was critical!
Modges'66 is offline   Reply With Quote
Old 09-03-2014, 01:53 AM   #84
Dinos63
chevy only
 
Dinos63's Avatar
 
Join Date: Sep 2006
Location: Phoenix, AZ
Posts: 6,619
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

man there is aton of nice work done.. dig it
__________________
CHEVY ONLY... Nothin Else !

Last edited by Dinos63; 09-09-2014 at 04:46 PM.
Dinos63 is offline   Reply With Quote
Old 09-03-2014, 09:50 AM   #85
severedchris
Registered User
 
severedchris's Avatar
 
Join Date: May 2012
Location: Franklinton, LA
Posts: 179
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Quote:
Originally Posted by Modges'66 View Post
Chris, my wheel is 11.5" wide which makes it 12.5" wide across the outside, and my tubs are 13.5 wide across the inside...Add to this the fact that my rear-end is all fresh and I didn't want to re-address it, or the costs of buying new axles...again!
My wheels are spaced to be within the INNER box side and the tub...
I didn't want the possibility of the return lip on the tub to ever come in contact with the tire, and I am running stock bed height/tub configuration (except for width).
I decided that is was a better choice to pay a little extra to buy a custom offset wheel to get the width & backspacing that I needed than to narrow the rear-end, and Travis at Pro-Performance really pulled this off for me!
Either way, the placement of the wheel was critical!
Modge your absolutely right man...this is why I ordered my wheels with a custom offset as well, however I went off of what Raceline recommended for an bagged 66 C10. Needless to say they were about an 1 5/8 off on their calculations.....they did offer to fix it but it was my choice to stick with the bigger lip and narrow the rearend.

Quote:
Originally Posted by Dinos63 View Post
man there is a done nice work done.. dig it
Thanks for the compliments bro!!!!
__________________
"The objective is not to die for my country, but to provide the other poor bastard the opportunity to die for his!!!!"
severedchris is offline   Reply With Quote
Old 09-03-2014, 05:59 PM   #86
Modges'66
Registered User
 
Modges'66's Avatar
 
Join Date: Feb 2012
Location: Grand Rapids, Michigan, otherwise known as Beer City U.S.A.
Posts: 1,081
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Quote:
Originally Posted by severedchris View Post
Modge your absolutely right man...this is why I ordered my wheels with a custom offset as well, however I went off of what Raceline recommended for an bagged 66 C10. Needless to say they were about an 1 5/8 off on their calculations.....they did offer to fix it but it was my choice to stick with the bigger lip and narrow the rearend.
Ahhh, I see!
The rears will look cooler with a bigger lip, IMO!
Modges'66 is offline   Reply With Quote
Old 09-03-2014, 06:23 PM   #87
severedchris
Registered User
 
severedchris's Avatar
 
Join Date: May 2012
Location: Franklinton, LA
Posts: 179
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Got some updates for you fellas

Rear end is off to get narrowed


Front bumper is fitted and sucked up to the body


Same treatment for the rear


Got the front fenders trimmed for the wheels and tires


Pic with the hood on


Finally!!!!! Got Paint on something!!!....slicked out all of the texture also

__________________
"The objective is not to die for my country, but to provide the other poor bastard the opportunity to die for his!!!!"
severedchris is offline   Reply With Quote
Old 09-03-2014, 06:33 PM   #88
Sac
Senior Member
 
Join Date: Nov 2013
Location: Franklinton, LA
Posts: 256
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Oh…..BOY!! That motor is looking on time!
Sac is offline   Reply With Quote
Old 09-03-2014, 09:04 PM   #89
JakeDW
Registered User
 
JakeDW's Avatar
 
Join Date: Jan 2013
Location: KCMO?
Posts: 453
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Really like those wheels with the spinners.Gona be a good lookin truck.

Jake
JakeDW is offline   Reply With Quote
Old 09-04-2014, 10:15 AM   #90
severedchris
Registered User
 
severedchris's Avatar
 
Join Date: May 2012
Location: Franklinton, LA
Posts: 179
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Quote:
Originally Posted by Sac View Post
Oh…..BOY!! That motor is looking on time!
Thanks Sac

Quote:
Originally Posted by JakeDW View Post
Really like those wheels with the spinners.Gona be a good lookin truck.

Jake
Appreciate it man
__________________
"The objective is not to die for my country, but to provide the other poor bastard the opportunity to die for his!!!!"
severedchris is offline   Reply With Quote
Old 09-04-2014, 10:58 AM   #91
1963c-10
Registered User
 
1963c-10's Avatar
 
Join Date: Nov 2011
Location: fayetteville nc
Posts: 10,338
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Nice work. And engine is looking great!!!
__________________
1963 Short bed step side SBW 427 big block and borg warner T-16 HD 3 speed manual
http://67-72chevytrucks.com/vboard/s...d.php?t=519869
1963 Short bed fleetside BBW 348 1st gen big block w/Powerglide
http://67-72chevytrucks.com/vboard/s...d.php?t=619024
1964 Short bed trailer
1963c-10 is offline   Reply With Quote
Old 09-04-2014, 03:52 PM   #92
severedchris
Registered User
 
severedchris's Avatar
 
Join Date: May 2012
Location: Franklinton, LA
Posts: 179
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Quote:
Originally Posted by 1963c-10 View Post
Nice work. And engine is looking great!!!
Thanks bro
__________________
"The objective is not to die for my country, but to provide the other poor bastard the opportunity to die for his!!!!"
severedchris is offline   Reply With Quote
Old 09-05-2014, 09:19 AM   #93
Jeff La
Registered User
 
Join Date: Dec 2011
Location: Donaldsonville, La.
Posts: 1,024
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Trucks coming out nice. Who's doing the work???
Jeff La is offline   Reply With Quote
Old 09-05-2014, 03:11 PM   #94
severedchris
Registered User
 
severedchris's Avatar
 
Join Date: May 2012
Location: Franklinton, LA
Posts: 179
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Quote:
Originally Posted by Jeff La View Post
Trucks coming out nice. Who's doing the work???
Thanks Jeff....Extreme Liners & Customs in Gonzales
__________________
"The objective is not to die for my country, but to provide the other poor bastard the opportunity to die for his!!!!"
severedchris is offline   Reply With Quote
Old 09-05-2014, 06:41 PM   #95
Modges'66
Registered User
 
Modges'66's Avatar
 
Join Date: Feb 2012
Location: Grand Rapids, Michigan, otherwise known as Beer City U.S.A.
Posts: 1,081
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

I need more pics dude!
I wanna see all of the latest progress!!!
Modges'66 is offline   Reply With Quote
Old 09-09-2014, 10:00 AM   #96
severedchris
Registered User
 
severedchris's Avatar
 
Join Date: May 2012
Location: Franklinton, LA
Posts: 179
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Sooo...we got some stuff accomplished over the weekend...here ya go!

We decided that the last firewall piece we made was inferior compared to the rest of the truck......so we threw it away and made a new one...4 times...lol...this is what we ended up with....and we are aware that the PB hinges are all wrong...were fixing that this week


I spent a few hours taping up the finned aluminum dress up goodies


We got the awesome Vintage Air Front Runner setup installed....more work than you would think.



The Sanderson Ceramic Coated Block Huggers....these things are really nice compared to stuff I've used in the past


Frame Prepped for Paint


Boom!!!...All done


A few detail shots


__________________
"The objective is not to die for my country, but to provide the other poor bastard the opportunity to die for his!!!!"
severedchris is offline   Reply With Quote
Old 09-09-2014, 12:35 PM   #97
severedchris
Registered User
 
severedchris's Avatar
 
Join Date: May 2012
Location: Franklinton, LA
Posts: 179
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Quote:
Originally Posted by Modges'66 View Post
I need more pics dude!
I wanna see all of the latest progress!!!
Happy Modge???....haha
__________________
"The objective is not to die for my country, but to provide the other poor bastard the opportunity to die for his!!!!"
severedchris is offline   Reply With Quote
Old 09-09-2014, 02:24 PM   #98
Thunderwagen
Registered User
 
Join Date: May 2011
Location: Fort Worth, Tx
Posts: 63
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

It looks awesome man!
__________________
1990 GMC Sierra
http://67-72chevytrucks.com/vboard/s...d.php?t=617587
Thunderwagen is offline   Reply With Quote
Old 09-09-2014, 02:41 PM   #99
severedchris
Registered User
 
severedchris's Avatar
 
Join Date: May 2012
Location: Franklinton, LA
Posts: 179
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

Quote:
Originally Posted by Thunderwagen View Post
It looks awesome man!
Thanks Thunderwagen
__________________
"The objective is not to die for my country, but to provide the other poor bastard the opportunity to die for his!!!!"
severedchris is offline   Reply With Quote
Old 09-09-2014, 04:46 PM   #100
Dinos63
chevy only
 
Dinos63's Avatar
 
Join Date: Sep 2006
Location: Phoenix, AZ
Posts: 6,619
Re: 65 C10 SWFS BBW "Clyde" @Poypeyes Rod Shop

killin it!
__________________
CHEVY ONLY... Nothin Else !
Dinos63 is offline   Reply With Quote
Reply

Bookmarks

Tags
1966, accuair, air ride, big window, chevrolet


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:03 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com