NJ Windsield Wiper Delay - Page 4 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**twouvakind** · 11-19-2013, 07:01 PM

To top

**twouvakind** · 11-20-2013, 07:09 PM

To top

**twouvakind** · 11-21-2013, 08:24 PM

To top

**twouvakind** · 11-22-2013, 01:50 PM

To top

**twouvakind** · 11-23-2013, 05:05 PM

To top

**twouvakind** · 11-25-2013, 12:12 AM

To top

**twouvakind** · 11-26-2013, 07:00 PM

To top

**jaros44sr** · 11-27-2013, 02:10 PM

OK Bill, got around to building the SW bezel nut, cant get the threads exactly right (M7X.75P),but it does thread on enough....my pitch gauge reads.75 on both the pot and nut, but only threads on halfway, dunno. Checked the tap also, and it checks out

Thanks for all your help

20131127_130241 by jarosaj, on Flickr

**twouvakind** · 11-27-2013, 08:03 PM

Great effort, please share the finished install here too!

Quote:

Originally Posted by jaros44sr

OK Bill, got around to building the SW bezel nut, cant get the threads exactly right (M7X.75P),but it does thread on enough....my pitch gauge reads.75 on both the pot and nut, but only threads on halfway, dunno. Checked the tap also, and it checks out

Thanks for all your help

20131127_130241 by jarosaj, on Flickr

**twouvakind** · 11-28-2013, 09:17 PM

To top

**twouvakind** · 11-29-2013, 08:59 PM

To top

**twouvakind** · 11-30-2013, 09:45 PM

To top

TobyArnot · 12-02-2013, 08:05 PM

Hey Bill,
Installed your unit recently and had to wait fo some rain(last weekend) to give it the test. Works great and I think I have found a knob the fits and look kinda' original.

Check it out . From Radio Shack.

**twouvakind** · 12-02-2013, 09:51 PM

Quote:

Originally Posted by TobyArnot

Hey Bill,
Installed your unit recently and had to wait fo some rain(last weekend) to give it the test. Works great and I think I have found a knob the fits and look kinda' original.

Check it out . From Radio Shack.

Very, very nice and quite non descript. Any problems drilling the bezel? How about pot shaft length? Did you shorten it? Looks great!

TobyArnot · 12-03-2013, 09:07 AM

Hey Bill,

I didn't have any problem with install. I used my pneumatic saw and removed about a 1-1/4" sq. opening where the choke cable hole was. I drilled a 5/16 hole in the bezel with no problem. Used a thin #10 (?) S.S. washer which I found in a "junk" box, with the supplied nut. The knob has a setscrew opposite the mark and will easily tighten [with a small screwdriver].
Great product and works as advertised. Will recommend to anyone.

**twouvakind** · 12-03-2013, 10:56 AM

Real clean install, nice job! Thanks for the Radio Shack part number too, will come in handy as that is a faq on installs.

**twouvakind** · 12-04-2013, 01:50 PM

To top

In The Ten Ring · 12-08-2013, 07:03 PM

Quote:

Originally Posted by TobyArnot

Hey Bill,
Installed your unit recently and had to wait fo some rain(last weekend) to give it the test. Works great and I think I have found a knob the fits and look kinda' original.

Check it out . From Radio Shack.

Well, that is neat. I might do something similar in the future....too many basic problems need fixing first!

**twouvakind** · 12-08-2013, 08:25 PM

Quote:

Originally Posted by In The Ten Ring

Well, that is neat. I might do something similar in the future....too many basic problems need fixing first!

Thank you for that, I'll have them when you are ready to commit!

**twouvakind** · 12-10-2013, 12:07 AM

To top

**twouvakind** · 12-10-2013, 05:54 PM

To top

**twouvakind** · 12-11-2013, 06:53 PM

To top

**twouvakind** · 12-14-2013, 10:59 AM

To top

**twouvakind** · 12-18-2013, 03:43 PM

To top

**twouvakind** · 12-21-2013, 12:41 PM

To top

11-19-2013, 07:01 PM	#76
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top

11-20-2013, 07:09 PM	#77
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top

11-21-2013, 08:24 PM	#78
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top

11-22-2013, 01:50 PM	#79
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top

11-23-2013, 05:05 PM	#80
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top

11-25-2013, 12:12 AM	#81
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top

11-26-2013, 07:00 PM	#82
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top

11-27-2013, 02:10 PM	#83
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,704	Re: Windsield Wiper Delay OK Bill, got around to building the SW bezel nut, cant get the threads exactly right (M7X.75P),but it does thread on enough....my pitch gauge reads.75 on both the pot and nut, but only threads on halfway, dunno. Checked the tap also, and it checks out Thanks for all your help 20131127_130241 by jarosaj, on Flickr __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

11-28-2013, 09:17 PM	#85
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top

11-29-2013, 08:59 PM	#86
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top

11-30-2013, 09:45 PM	#87
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top

12-02-2013, 08:05 PM	#88
TobyArnot Quit if it's not FUN!!! Join Date: Jul 2010 Location: Indian Trail, N.C, Posts: 864	Re: Windsield Wiper Delay Hey Bill, Installed your unit recently and had to wait fo some rain(last weekend) to give it the test. Works great and I think I have found a knob the fits and look kinda' original. Check it out . From Radio Shack. Attached Images __________________ MY MOTTO: Eat it all up, Wear it out, Use the last few drops, Spend all you've got, Late in life, you'll think of the things you didn't do, not the things you did. - Get out and experience life ! . Robbie Robinson a.k.a. TobyArnot (Toe Bee or not toe bee)

12-03-2013, 09:07 AM	#90
TobyArnot Quit if it's not FUN!!! Join Date: Jul 2010 Location: Indian Trail, N.C, Posts: 864	Re: Windsield Wiper Delay Hey Bill, I didn't have any problem with install. I used my pneumatic saw and removed about a 1-1/4" sq. opening where the choke cable hole was. I drilled a 5/16 hole in the bezel with no problem. Used a thin #10 (?) S.S. washer which I found in a "junk" box, with the supplied nut. The knob has a setscrew opposite the mark and will easily tighten [with a small screwdriver]. Great product and works as advertised. Will recommend to anyone. __________________ MY MOTTO: Eat it all up, Wear it out, Use the last few drops, Spend all you've got, Late in life, you'll think of the things you didn't do, not the things you did. - Get out and experience life ! . Robbie Robinson a.k.a. TobyArnot (Toe Bee or not toe bee)

12-03-2013, 10:56 AM	#91
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay Real clean install, nice job! Thanks for the Radio Shack part number too, will come in handy as that is a faq on installs.

12-04-2013, 01:50 PM	#92
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top



Register or Log In To remove these advertisements.

12-10-2013, 12:07 AM	#95
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top

12-10-2013, 05:54 PM	#96
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top

12-11-2013, 06:53 PM	#97
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top

12-14-2013, 10:59 AM	#98
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top

12-18-2013, 03:43 PM	#99
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top

12-21-2013, 12:41 PM	#100
twouvakind Senior Member Join Date: Dec 2011 Location: South Carolina Posts: 2,662	Re: Windsield Wiper Delay To top

Register or Log In To remove these advertisements.