1948 Chevy project

[J48chevy]

Well change coming in the build. Instead of the 305 now looks like I will have a LS going in. My buddy finally talked me into it. Will post pics when I get it.

[iowaboynca]

sweet! looking forward to it.

[Tikal48]

Your build is coming along nicely. Very nice work! Hope you won the battle of the doors. I'm fighting that battle now myself. I bought all new hinges, but now I have a hybrid set of the old and new hinges, that wound up giving me the best fit. I have rust problems on the bottom of both doors, so I am having to install inside and outside patch panels.

I'm also in the process of changing to the large bear claw latches, and want to add the flush mount door handles. This battle could last a while!

Congratulations and good luck with the LS! What transmission are you planning on putting behind it?

[J48chevy]

Thanks. Going to do the bear claw install as well. Right now the plans are to use the 700r4 auto trans with it. Still a lot of time to decide as my build is going slow but then again I am in no hurry.

[99 to Life]

hey guys, don't wanna hijack you here. but I feel your pain on the doors. I can't even tell you how much work goes into those, its alot. anyway. I did up a prototype bolt on kit. I'm going to have these made in bulk eventually. It uses a large bear claw. I was able to get the inner door handles to work on opening and for the outside its just a pull handle (handle is stationary). The system uses an actuator in the door to pop open the latch. Similar to shaved handles, but you actually have a handle. There is a video on my build on page 27 post #674, and pics on #671. build page is in my signature the 49'

Something to think about. I'v seen guys use 52-55 door handles and put a momentary switch in the button, so it looks stock, but when you press the button it activates the actuator and pops the lock open.

as for inner and outter door skins. I made both on my last project. The outter can def be a pain. you'd need a slip roll or something to shape the metal. I see outter skins for like $30 a piece, thought about tryin them out to save a little time. The inner skin is really easy to make. It is nice to have the door all cut up so you can actually get in there and coat the inside of it.

[J48chevy]

Thanks. I will check that out on your page.

[J48chevy]

I was able to get the cab floor done and put chassis saver on floor and bottom. Also made a seat frame and mocked up my seats. Making slow progress. Hoping to get my LS motor installed in the next 2-3 weeks.

[J48chevy]

Floor pic

[Dan in Pasadena]

Haven't been back to your thread in awhile. Looks like you're really making progress. I've still not welded in my IFS as my project took a turn and is now a frame off and the cab and doors are in the bodyshop.

What are your seats from? They're very nice looking as is. Do you plan to keep or remove the headrests? Any details on how they mount?

[J48chevy]

Thanks. Seats are out of a 2008 impala ss. I am not sure if I will keep head rests or not. As for seat mounting, I had to fabricate a frame to bolt to seat then floor. I have the drivers side done now need to do one for other seat. Good thing is seats have all power options and heat which I will hook up.

[J48chevy]

A few steps forward. Fitting the LS. Think I am going to like it.

[J48chevy]

One more pic.

[J48chevy]

Well as I have said many times, it's a slow build. Haha. Here are a few pics from some body work. Hoping to have cab wrapped up in a few weeks and get it back on the chassis.

[J48chevy]

One more. Not sure why they are showing sideways lately.

[J48chevy]

Backside.

[J48chevy]

Door gap coming along nicely.

[J48chevy]

Another door gap pic.

[J48chevy]

...

[oldman3]

Looks great...Jim

[youngrodder]

The body work looks great.

Marc

[99 to Life]

mighty clean.

[cwii]

J48,
I like where this is heading and it is looking good.I am in the early stages of a similar build with a 47 long bed,LS3,TR6060, and a had a question about your wheel base. in a previous post you mentioned 129 in; did that center the tire in the rear well? mine is at 127 but I do not have a bed as of yet to mock up .
Maybe some day I will learn how to attach pix and a post couple of my own.
Thanks, Chuck

[J48chevy]

cwii,
Cannot wait to see some pics from yours. Mine is a really slow build as it is my first. Learning as I go and asking lots of questions. Anyhow my wheel base is due to me moving the rear end back so my rear wheels are centered in the wheel well. These truck all have the rear tire set to the front of the wheel well and I liked the center better. Especially since I am running bigger tires. Right now I have 18's but am concidering 20's also.

[JSavoie]

This project was very interesting. What happened in the last 6 months please?

[J48chevy]

Not much as it might be the slowest build ever. Haha. Just not much time. I will post a few pics as the body is getting ready to go back on and I will start running electrical and doing interior.