66 GMC Long to Short LS Swap - Page 4 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Duncan K · 10-08-2018, 05:45 PM

Did a little more work done on the motor. Finished installing the other bank of pistons and rods. Lubed up the new Comp Cam and slid it in place. New billet roller timing set, and a high flow Melling oil pump.

Taped up the block and hit it with a coat of rust converter followed by a few coats of Chevy Orange. Painted the front and valley covers as well. Buttoned up the bottom end with a freshly hot tanked oil pan.

[/url]

Lokin4AReason · 10-09-2018, 11:20 AM

nice progress on the project ...

Notch1988 · 10-11-2018, 11:45 PM

Keep the updates coming

Slammed96 · 10-12-2018, 07:34 PM

Nice build! Depending on how low you are you may consider an f body oil pan for your set up. The truck pans hang a bit low for my comfort on a lowered truck. Also, curious if that's a boyds welding fuel tank you webt with, and if so, how low it hangs below the frame?

Duncan K · 10-13-2018, 09:59 PM

Quote:

Originally Posted by Slammed96

Nice build! Depending on how low you are you may consider an f body oil pan for your set up. The truck pans hang a bit low for my comfort on a lowered truck. Also, curious if that's a boyds welding fuel tank you webt with, and if so, how low it hangs below the frame?

I have been debating going with the F body pan. My truck's not too low,5.5/7 drop, but I'd feel better with the pan being tucked up out of harms way. Just one more thing to add to my budget. I did go with the Boyd's Welding tank, I'll measure the clearance from the ground next time I am out at the shop.

Duncan K · 11-04-2018, 08:41 PM

Got my heads back from the machine shop, had them vacuum tested, tanked, and decked. Installed the new seals and dual springs

I blasted and painted the water and power steering pumps, all the pulleys and brackets and got them painted up and mounted. Dropped in some new lifters and bolted the heads on.

Blasted and painted the motor mounts

Coat of paint on the transmission as well

At this point the engine is pretty much button up. Still need to clean up the coils and brackets and throw the intake on. Also planning to get the alternator shell blasted and painted.

Notch1988 · 11-06-2018, 12:00 AM

Looking good.

Duncan K · 11-17-2018, 12:44 PM

Plumbed in new front brake lines

Got the engine and trans mated up and dropped in the chassis

Slammed96 · 11-17-2018, 01:35 PM

What headers are those? They look like they fit like a glove.

Duncan K · 11-17-2018, 08:48 PM

Quote:

Originally Posted by Slammed96

What headers are those? They look like they fit like a glove.

Speed Engineering long tubes. They fit really well, only had to trim a tiny bit of the bell housing on the passenger side.

Sledgebone · 11-19-2018, 12:43 PM

Looking good. I have the same mount plates and I'm thinking of using the I6 perches as well. Are those the Energy Suspension poly mounts? What location do you have them bolted to the plates?

Duncan K · 11-19-2018, 01:04 PM

Quote:

Originally Posted by Sledgebone

Looking good. I have the same mount plates and I'm thinking of using the I6 perches as well. Are those the Energy Suspension poly mounts? What location do you have them bolted to the plates?

They are Energy Suspension poly mounts but they don't fit. Way thicker than the stock ones that I used when i mocked up the perchs, gotta return themand use a set of stock rubber ones. I used the stock V8 perches, mounts are in the second set of holes from the front

Duncan K · 12-28-2018, 06:36 PM

Slow progress lately. Pulled the motor and trans back out to swap mounts. Ended up getting the trans rebuilt while it was out. Cleaned up and painted the coils and brackets and threw on some new plug wires. Motor is back in and intake on. Just have to clean up the fuel rails and throttle body.

Started back on the rust repair on the cab. Got the passenger side floor finished and started fitting up the rocker. Hung the door so i could get the gap right.

The bottom of the back wall of the cab is rusted out. I wasn't sure exactly how I was going to tackle this repair until I came across a guy giving away a full back wall.

Notch1988 · 01-06-2019, 11:04 PM

Looking for my weekly fix...

SCOTI · 01-07-2019, 08:06 PM

Cool build. Lots or good work going on here!

Duncan K · 01-07-2019, 11:01 PM

Here ya go Notch!

Moving along with the rust repair. Made a pile of relief cuts, did a lot of bending and hammering. Rocker is all fit up ready to weld in. Going to wait on that until I get the cab sand blasted.

Finished a bit of work on the passenger floor. Had to weld in a small sliver from a previous crappy fit up. Replaced a piece of the trans tunnel hump as well.

Moved on the the kick panel firewall seam. Drilled out all the spot welds and made a template for what i wanted to replace.

Transferred the template to some 18g and cut it out. once i was happy with the fit I cut out the kick panel section.

Made the bends for where the fire wall gets spot welded to the kick panel. Fine tuned the fit and its ready to weld in.

The inside of the door pillar was pretty rusty. Found a rust encapsulator product from Eastwood with a long hose and 360 Degree nozzle. Shoved it up the pillar and coated the whole inside top to bottom. Will let that cure overnight and start welding in the kick panel patch tomorrow.

**Captainfab** · 01-08-2019, 12:52 AM

Nice job on the metal work!

northern 85 · 01-08-2019, 01:42 PM

Yes lots of metal magic on this one! Very nice!

Duncan K · 01-26-2019, 11:36 PM

Slowly chipping away at the rust repair. Finished up the kick panel and started on the firewall.

Built a sandblasting cabin and wheeled the cab inside. Started blasting the cab to see what was surface rust and what needed to be cut out. I was really happy to find the areas above the windshield were not rusted through and cleaned up really well. The lip that the windshield seal goes around is a different story though. That is gonna suck to repair!!

Back onto the firewall/floor seam. Got most of the remaining pieces made and fit. Hopefully will get time to them all welded in this week.

**Captainfab** · 01-27-2019, 01:29 AM

Nice job on the metal work

SkinnyG · 01-27-2019, 12:21 PM

How effective are you finding that sand blaster, and what size is your compressor?

Duncan K · 01-27-2019, 12:37 PM

Quote:

Originally Posted by SkinnyG

How effective are you finding that sand blaster, and what size is your compressor?

Surprisingly its been working pretty well, my compressor is a 60 gallon. I'm using 30-60 grit crushed glass from Princess Auto. Takes a bit of time to sweep up, sift and reload the pressure tank but its cheap and I can do it in stages as i go along.

SCOTI · 01-27-2019, 02:29 PM

Quote:

Originally Posted by Duncan K

Surprisingly its been working pretty well, my compressor is a 60 gallon. I'm using 30-60 grit crushed glass from Princess Auto. Takes a bit of time to sweep up, sift and reload the pressure tank but its cheap and I can do it in stages as i go along.

I was just thinking of something like this yesterday for a temporary parking lot set-up adjacent to my shop building. I'm interested/curious about your pop-up 'booth' for the blasting. Care to share the details? How did you seal it off (top; bottom; entrance/exit)?

SkinnyG · 01-27-2019, 04:44 PM

Is that a PA blaster as well?

I was planning on taking everything to "the man" and have them blast it all, but I really need to deal with the rust inside everything I have to cut out (like the rockers, corners, etc. etc.)

What HP and CFM is your compressor?

Duncan K · 01-27-2019, 05:33 PM

My booth is pretty simple, just a 2x4 frame 10ftx10ft, 8ft tall wrapped in poly. I didn't really seal it up too much, just wanted to keep the sand from getting all over the shop.

Blaster is Princess Auto, I run a couple dryers inline to the tank. This is the compressor

https://www.aircompressorsdirect.com...ssor/p705.html

10-08-2018, 05:45 PM	#76
Duncan K Registered User Join Date: Oct 2017 Location: Calgary, Alberta Posts: 210	Re: 66 GMC Long to Short LS Swap Did a little more work done on the motor. Finished installing the other bank of pistons and rods. Lubed up the new Comp Cam and slid it in place. New billet roller timing set, and a high flow Melling oil pump. Taped up the block and hit it with a coat of rust converter followed by a few coats of Chevy Orange. Painted the front and valley covers as well. Buttoned up the bottom end with a freshly hot tanked oil pan. [/url] __________________ 66 GMC 910 My Build thread http://67-72chevytrucks.com/vboard/s...d.php?t=754257

10-09-2018, 11:20 AM	#77
Lokin4AReason Registered User Join Date: Oct 2014 Location: somewhere . . . Posts: 969	Re: 66 GMC Long to Short LS Swap nice progress on the project ... __________________ dont want to hear excuses, i want to hear solution(s)

10-11-2018, 11:45 PM	#78
Notch1988 Registered User Join Date: Aug 2009 Location: Lacombe, Alberta Posts: 335	Re: 66 GMC Long to Short LS Swap Keep the updates coming __________________ 66 GMC swb dropmember accuair Link to my build: My GMC Project

10-12-2018, 07:34 PM	#79
Slammed96 Registered User Join Date: Apr 2013 Location: Olathe KS Posts: 156	Re: 66 GMC Long to Short LS Swap Nice build! Depending on how low you are you may consider an f body oil pan for your set up. The truck pans hang a bit low for my comfort on a lowered truck. Also, curious if that's a boyds welding fuel tank you webt with, and if so, how low it hangs below the frame? __________________ 14 Silverado- 4/6 drop daily 66 GMC short wide Custom Cab- building to be low and cruise. 4.8/t56 swap occurring now. Stupid low static drop 66 GMC 1 ton stepside looooong bed- the tow pig/work truck.

11-04-2018, 08:41 PM	#81
Duncan K Registered User Join Date: Oct 2017 Location: Calgary, Alberta Posts: 210	Re: 66 GMC Long to Short LS Swap Got my heads back from the machine shop, had them vacuum tested, tanked, and decked. Installed the new seals and dual springs I blasted and painted the water and power steering pumps, all the pulleys and brackets and got them painted up and mounted. Dropped in some new lifters and bolted the heads on. Blasted and painted the motor mounts Coat of paint on the transmission as well At this point the engine is pretty much button up. Still need to clean up the coils and brackets and throw the intake on. Also planning to get the alternator shell blasted and painted. __________________ 66 GMC 910 My Build thread http://67-72chevytrucks.com/vboard/s...d.php?t=754257

11-06-2018, 12:00 AM	#82
Notch1988 Registered User Join Date: Aug 2009 Location: Lacombe, Alberta Posts: 335	Re: 66 GMC Long to Short LS Swap Looking good. __________________ 66 GMC swb dropmember accuair Link to my build: My GMC Project

11-17-2018, 12:44 PM	#83
Duncan K Registered User Join Date: Oct 2017 Location: Calgary, Alberta Posts: 210	Re: 66 GMC Long to Short LS Swap Plumbed in new front brake lines Got the engine and trans mated up and dropped in the chassis __________________ 66 GMC 910 My Build thread http://67-72chevytrucks.com/vboard/s...d.php?t=754257

11-17-2018, 01:35 PM	#84
Slammed96 Registered User Join Date: Apr 2013 Location: Olathe KS Posts: 156	Re: 66 GMC Long to Short LS Swap What headers are those? They look like they fit like a glove. __________________ 14 Silverado- 4/6 drop daily 66 GMC short wide Custom Cab- building to be low and cruise. 4.8/t56 swap occurring now. Stupid low static drop 66 GMC 1 ton stepside looooong bed- the tow pig/work truck.

11-19-2018, 12:43 PM	#86
Sledgebone Registered User Join Date: Oct 2015 Location: Mi Posts: 24	Re: 66 GMC Long to Short LS Swap Looking good. I have the same mount plates and I'm thinking of using the I6 perches as well. Are those the Energy Suspension poly mounts? What location do you have them bolted to the plates?

12-28-2018, 06:36 PM	#88
Duncan K Registered User Join Date: Oct 2017 Location: Calgary, Alberta Posts: 210	Re: 66 GMC Long to Short LS Swap Slow progress lately. Pulled the motor and trans back out to swap mounts. Ended up getting the trans rebuilt while it was out. Cleaned up and painted the coils and brackets and threw on some new plug wires. Motor is back in and intake on. Just have to clean up the fuel rails and throttle body. Started back on the rust repair on the cab. Got the passenger side floor finished and started fitting up the rocker. Hung the door so i could get the gap right. The bottom of the back wall of the cab is rusted out. I wasn't sure exactly how I was going to tackle this repair until I came across a guy giving away a full back wall. __________________ 66 GMC 910 My Build thread http://67-72chevytrucks.com/vboard/s...d.php?t=754257

01-06-2019, 11:04 PM	#89
Notch1988 Registered User Join Date: Aug 2009 Location: Lacombe, Alberta Posts: 335	Re: 66 GMC Long to Short LS Swap Looking for my weekly fix... __________________ 66 GMC swb dropmember accuair Link to my build: My GMC Project

01-07-2019, 08:06 PM	#90
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,041	Re: 66 GMC Long to Short LS Swap Cool build. Lots or good work going on here! __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

01-07-2019, 11:01 PM	#91
Duncan K Registered User Join Date: Oct 2017 Location: Calgary, Alberta Posts: 210	Re: 66 GMC Long to Short LS Swap Here ya go Notch! Moving along with the rust repair. Made a pile of relief cuts, did a lot of bending and hammering. Rocker is all fit up ready to weld in. Going to wait on that until I get the cab sand blasted. Finished a bit of work on the passenger floor. Had to weld in a small sliver from a previous crappy fit up. Replaced a piece of the trans tunnel hump as well. Moved on the the kick panel firewall seam. Drilled out all the spot welds and made a template for what i wanted to replace. Transferred the template to some 18g and cut it out. once i was happy with the fit I cut out the kick panel section. Made the bends for where the fire wall gets spot welded to the kick panel. Fine tuned the fit and its ready to weld in. The inside of the door pillar was pretty rusty. Found a rust encapsulator product from Eastwood with a long hose and 360 Degree nozzle. Shoved it up the pillar and coated the whole inside top to bottom. Will let that cure overnight and start welding in the kick panel patch tomorrow. __________________ 66 GMC 910 My Build thread http://67-72chevytrucks.com/vboard/s...d.php?t=754257

01-08-2019, 12:52 AM	#92
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,251	Re: 66 GMC Long to Short LS Swap Nice job on the metal work! __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

01-08-2019, 01:42 PM	#93
northern 85 Registered User Join Date: Mar 2005 Location: Fairfield Maine Posts: 1,759	Re: 66 GMC Long to Short LS Swap Yes lots of metal magic on this one! Very nice!



Register or Log In To remove these advertisements.

01-26-2019, 11:36 PM	#94
Duncan K Registered User Join Date: Oct 2017 Location: Calgary, Alberta Posts: 210	Re: 66 GMC Long to Short LS Swap Slowly chipping away at the rust repair. Finished up the kick panel and started on the firewall. Built a sandblasting cabin and wheeled the cab inside. Started blasting the cab to see what was surface rust and what needed to be cut out. I was really happy to find the areas above the windshield were not rusted through and cleaned up really well. The lip that the windshield seal goes around is a different story though. That is gonna suck to repair!! Back onto the firewall/floor seam. Got most of the remaining pieces made and fit. Hopefully will get time to them all welded in this week. __________________ 66 GMC 910 My Build thread http://67-72chevytrucks.com/vboard/s...d.php?t=754257

01-27-2019, 01:29 AM	#95
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,251	Re: 66 GMC Long to Short LS Swap Nice job on the metal work __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

01-27-2019, 12:21 PM	#96
SkinnyG Registered User Join Date: Feb 2012 Location: Beautiful BC, Canada, eh?! Posts: 2,252	Re: 66 GMC Long to Short LS Swap How effective are you finding that sand blaster, and what size is your compressor? __________________ 1961 Apache: "Grabber Orange" Shortboxed, pancake, step-notch, air-ride, boosted-LS 1977 Silverado: Shortboxed & dropped, potato-potato V8 Pontiac Firefly (Chevy Sprint): The ultimate engine swap: 5.7L in a 1.0L bag Lotus Super 7 Replica: Scratch-built street-legal rollerskate

01-27-2019, 04:44 PM	#99
SkinnyG Registered User Join Date: Feb 2012 Location: Beautiful BC, Canada, eh?! Posts: 2,252	Re: 66 GMC Long to Short LS Swap Is that a PA blaster as well? I was planning on taking everything to "the man" and have them blast it all, but I really need to deal with the rust inside everything I have to cut out (like the rockers, corners, etc. etc.) What HP and CFM is your compressor? __________________ 1961 Apache: "Grabber Orange" Shortboxed, pancake, step-notch, air-ride, boosted-LS 1977 Silverado: Shortboxed & dropped, potato-potato V8 Pontiac Firefly (Chevy Sprint): The ultimate engine swap: 5.7L in a 1.0L bag Lotus Super 7 Replica: Scratch-built street-legal rollerskate

01-27-2019, 05:33 PM	#100
Duncan K Registered User Join Date: Oct 2017 Location: Calgary, Alberta Posts: 210	Re: 66 GMC Long to Short LS Swap My booth is pretty simple, just a 2x4 frame 10ftx10ft, 8ft tall wrapped in poly. I didn't really seal it up too much, just wanted to keep the sand from getting all over the shop. Blaster is Princess Auto, I run a couple dryers inline to the tank. This is the compressor https://www.aircompressorsdirect.com...ssor/p705.html __________________ 66 GMC 910 My Build thread http://67-72chevytrucks.com/vboard/s...d.php?t=754257

Register or Log In To remove these advertisements.