Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
|
04-30-2017, 05:45 PM | #1 |
Registered User
Join Date: Sep 2012
Location: Midway, NC
Posts: 3,275
|
Re: Fixin Dixie - 66 Short Bed Fleetside
Looking good. Keep at it.
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=581873 The low buck build threads. Check'em out! http://67-72chevytrucks.com/vboard/s...d.php?t=666022 My build thread Crossmembers CC |
05-01-2017, 10:30 AM | #2 |
Registered User
Join Date: Jul 2015
Location: smyrna georgia
Posts: 54
|
Re: Fixin Dixie - 66 Short Bed Fleetside
Great job, Makes me want to start on the sheetmetal now!
|
05-07-2017, 10:39 PM | #3 |
Registered User
Join Date: Feb 2013
Location: GA
Posts: 1,313
|
Re: Fixin Dixie - 66 Short Bed Fleetside
Thanks guys! I figured out why the rocker panel was taller at that front end. I cut a profile of the original rocker and placed it on the repop and its definitely taller, and the reason is in the manufacturing the brace was misaligned and threw it off. So I cut out the brace, cut a new end brace from scrap and epoxy primered it fit in place. Since the panel was taller from the manufacture mishap I had to clamp it down to the bench and use the metal bar from the brake I have and took clamps to use to bend it up and get it back where it should be.
Then I welded it up. Now the rocker is fitting way better! |
05-16-2017, 01:26 AM | #4 |
Registered User
Join Date: Feb 2013
Location: GA
Posts: 1,313
|
Re: Fixin Dixie - 66 Short Bed Fleetside
While I was waiting on the epoxy primer to cure up on repairs I was making to the rocker and fender I decided to get the passenger door repair started. This time I removed most of the front door panel and was able to weld up the hole I cut out thinking I could use it as access to hammer/dolly the botched weld up I did a while back. Once I had the hole patched I epoxy primered the interior some more. Then I taped up areas that I wanted to apply seam sealer to just as a precaution. Then I started applying the sound deadener Noico product I bought. Ive read this helps the rattle of the metal panels so I applied it to where it made sense. The Dynamat sample they sent was interesting by comparison, side by side the Noico was a little thicker.
Hopefully that will help the sound on the interior, which at the rate Im going will be 2019 Then I got the rocker installed, I had to do as you mentioned Vince and cut along therdges of the horn looking part at the front. Used the self tapping screws, but I ended up needing to drill the pilot hole first. Didnt self tap Like I hoped. Once I got the rocker tacked in I got busy on the cab corner and knocked it out. Not perfect but works. Getting closer! I just need to finish welding the base of the rocker to the inner rocker at he base then I think Ill finish up the passenger door. |
06-16-2017, 10:38 AM | #5 |
Moderator
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
|
Re: Fixin Dixie - 66 Short Bed Fleetside
Impressive skills MSG.
__________________
Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats? |
06-16-2017, 12:20 PM | #6 |
Registered User
Join Date: Apr 2011
Location: .
Posts: 3,104
|
Re: Fixin Dixie - 66 Short Bed Fleetside
Following along.
|
06-19-2017, 01:28 AM | #7 |
Registered User
Join Date: Feb 2013
Location: GA
Posts: 1,313
|
Re: Fixin Dixie - 66 Short Bed Fleetside
Thanks RocknRod, learning as I go. This site and its members have been invaluable to me, couldn't get this far without it!
Hey Bomp, you gave me some great links in post #6 about 3 years ago! Watching the work you do and you truck collection is amazing. Great to have you fellas following me along...I'll try and pick up the pace. I have been pretty busy but not updating too good. So here is a little of whats been done,Ill post more tomorrow. So to pick back up, I had decided to cut the door skin up past the handle since that part of the panel had too many rust spots for my liking, so I got the spot weld cutting tool and drilled out the 3 spots holding it on. Then I got the wire wheel aand sander to it and some ospho for the rust and cleaned it up real good, then applied 3 coats of epoxy primer. Then I welded it onto the patch panel door skin. The big dilemma I had was about being able to be able to reach inside and hammer/dolly as I went along to keep it from having the warpage that got me into this mess in the first place. I wasnt able to cut too high up where the brace is,since the access to hammer/dolly wouldnt be there.Plus it already has support so I notched around it. Then I applied the Noico vibration dampner and got some clamps out and started surgery. The last pic there shows a profile of the welded patch to the existing door. I was ok with it, but the problem I was having was that the dolly i would need for the location I was welding really needed to be concave and all the ones I have are flat or convex. I can live with it, hopefully the body filler will smooth it out. At least its a better result than what I did the first time in this thread http://67-72chevytrucks.com/vboard/s...d.php?t=690647 Ill update more tomorrow! |
06-20-2017, 12:39 AM | #8 |
Registered User
Join Date: Feb 2013
Location: GA
Posts: 1,313
|
Re: Fixin Dixie - 66 Short Bed Fleetside
With the door skin finally on the passenger side, I wanted to hang it and see how it fit. The best way I have found to do this solo is to tape spacers in the inner door jamb..in my case I used some cut off paint sticks about 1/8 inch thick...and I hung it up and used a ratcheting tie down strap in the rear portion to keep it in place.
Once I got the door skin on I measured the length of the base of the door and also measured the length of the patch rocker panel and of course the rocker was too long by 3/8" So that happy dance I did in post #79 I now take back. I had to do the same shortening task I went through on the driver side. I used the self tapping screws to position the rocker so it lined up right with the door and then hung the front fender to check that its lined up decent. I then welded in the base and a few spots on the ends of the rocker until I get the door off to be able to finish. Still have finessing to do but its fitting now. Then I got to the cab corner, took 3 self tapping screws to position it so I can take measure out how much I needed to add to what the patch panel didnt come with. So I took the panel I fabricated in post #68 while working on the driver side from before and welded on the extension, got it epoxy primered up and ready to weld. Then it was safety check time, the stand I put together has been slowly sagging to the front with all the rolling around and just being plain ole heavy. Plus I dont think keeping it on there for more than a year helps. So I had to get the engine hoist with the wooden rig I put together on and lift the cab up and pullout the stand to add some metal bracing. Now its standing straight. Now I can get to the cab corner without worrying about it caving in on me. Lastly I have some things to share I have been stockpiling that I wanted on Dixie.
I look forward to getting to deal with these one day soon! |
06-26-2017, 01:17 AM | #9 |
Registered User
Join Date: Feb 2013
Location: GA
Posts: 1,313
|
Re: Fixin Dixie - 66 Short Bed Fleetside
Had an amazing weekend, went eastbound an down and got to see Burt Reynolds and cast members tell stories about making the Smokey and The Bandit film during a 40th Anniversary Bandit Run event, plus a fleet of trans ams! Always loved that movie.
Left to right: Fella that played a State Patrol officer, Sister to girl on the right of Burt, The Bandit himself, Woman in blacktop she was the little girl at the beginning of the movie who said "Hey Uncle Bandit!", Hot Pants Hilliard, Jerry Reed's daughter, The guy who owned the hound dog Fred. Then the next hilight and milestone was finally finishing the worst of the body panel repairs on the cab!!! I got the rear cab corners and the rockers all welded in. Next there are few minor spots to deal with in the floor and I can move onto planning to get some paint going!! Cant wait. |
06-26-2017, 06:51 AM | #10 |
Registered User
Join Date: Oct 2009
Location: canton ga
Posts: 12,728
|
Re: Fixin Dixie - 66 Short Bed Fleetside
The cab is looking great . I would love to do see the Bandit Run sometime ,wish I still had my Bandit T/A . I plan to sell my 81 T/A in the near future ,tryin g to downsize the herd more .
|
06-27-2017, 11:22 PM | #11 |
Registered User
Join Date: Nov 2014
Location: Red Deer, Alberta, Canada
Posts: 166
|
Re: Fixin Dixie - 66 Short Bed Fleetside
Looking good! Thanks for posting! Keep up the good work.
|
07-04-2017, 08:31 AM | #12 |
Registered User
Join Date: Feb 2013
Location: GA
Posts: 1,313
|
Re: Fixin Dixie - 66 Short Bed Fleetside
Crumby ol photobucket! That stinks, ransom for displaying the pics I have been posting all these years. Using their site was a bad experience enough with all of the ads and pop ups and viruses I bet my computer has from it. I hate to do it, but unless there is another way to update each post from the past I would probably be better off starting an new thread and just upload the pics to this site vs linking out.
As a test on the inserting pics I'll post this pic and ask about holes in the floor. The 2 large ones left and right of the center hump I assume is for AC drain lines. I do plan to have AC this time so I think those stay,but there are some others I think are supposed to be drain holes as well. Do ya'll keep these or weld them up? Happy 4th!!!! |
Bookmarks |
|
|