Project Patina Burb - Page 4 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

5150 · 08-18-2012, 07:42 PM

My floor has 4 holes. I'm probably going to put a 3 point harness on one side, like the one I had on my blazer, for my youngest little girl. I'll put a normal 3 point shoulder belt on the other side for my 7 year old.

The third row will be factory.

5150 · 08-18-2012, 08:20 PM

Here's the type of harness I plan on using for my little girl. I figured it would be better then having the shoulder harness stretched across that far over to buckle her in.

**kev2809** · 08-18-2012, 09:11 PM

nice..i like the idea

whos truck is that in the pic?

5150 · 08-18-2012, 09:34 PM

That's my old blazer

**lolife99** · 08-18-2012, 09:55 PM

Bryan,... did you sell the blazer, or do you still have it?

**Hart_Rod** · 08-18-2012, 09:58 PM

Quote:

Originally Posted by 5150

My floor has 4 holes. I'm probably going to put a 3 point harness on one side, like the one I had on my blazer, for my youngest little girl. I'll put a normal 3 point shoulder belt on the other side for my 7 year old.

The third row will be factory.

Sounds like I have your seat and you have mine. Wanna trade seat bottoms?

. There should be places to bolt the seatbelts to on those rear brackets.
Posted via Mobile Device

5150 · 08-18-2012, 09:58 PM

No, I sold it last October. We had another little girl, Lizzy, last August. Between my small business doing really bad and hospital bills started coming in, I sold it. I didn't miss it until April

5150 · 08-18-2012, 10:01 PM

Looking back at the original post in this thread, you can see the original second row seat that I gave away had the four brackets on the rear. I'll probably use one of them to bolt the 3 point harness to.

5150 · 08-18-2012, 10:20 PM

Here's my hatch that I picked up from the owner of SOKY Classics

5150 · 08-25-2012, 02:23 PM

Got alot of the wiring done on the air ride today. I'm running Slams in the front and the PO gave me these HUGE Goodyear bags that I'm using on the rear. I believe they came from a bus. I also am using the older style Ride Tech Digital Pressure sensor and 4 sensors that I got from smbrouss70.

I mounted the tank and the compressor. Also put the valves together with pressure sensors and mounted them in the best locations. Wired everything up, but I don't have a battery in it. I've had it on schrader valves for awhile now.

I still have to wire up the switch box and put some 90 degree fittings on the rear, wire up the compressor with relay, and mount the water trap(I just ordered it).

5150 · 09-02-2012, 07:06 PM

okay, finished up the wiring today on the air bags except for wiring up the switch box. I needed a few more connectors.

I had some help from my daughter, Halen, who loves to work on it with me.

Dropped the drive shaft and got a measurement on how much to shorten it for it to fit the 4L60E.

502ms · 09-04-2012, 08:57 PM

Very nice!
Posted via Mobile Device

oldblue1968chevy · 09-27-2012, 02:34 AM

I think I have you on FB

Are you bryan?

Anyways, cool build Im following along.

5150 · 11-10-2012, 09:54 PM

Got most of the fuel line ran today. Still have to install the tank, but all the line has been ran to the rear of the burb.

5150 · 11-29-2012, 08:15 PM

Got the tank in and wired up. Got it off jack stands for the first time in a couple of months.

Still messing with the new wiring harness. It's an 21 circuit EZ Wiring harness and it's a bit overwhelming to say the least.
Posted via Mobile Device

jeffg1010 · 12-31-2012, 12:28 PM

Subscribed. Cant wait to see it on the Power Tour

Posted via Mobile Device

5150 · 01-01-2013, 06:19 PM

Got a few things done today. I got my carpet kit in from Brother's this week also. I'm kind of collecting parts as of late.

Cleaned up some of the metal interior trip today with the bench grinder. I slapped the wire wheel attachment on it and cleaned most of the surface rust that was on them.

5150 · 01-01-2013, 06:30 PM

I also saw another problem I'm going to have to deal with due to the PO shaving certain things.

I have a good hatch, but the push button has been shaved so I'm not sure how I'm going to get it open from the outside.

Rusbuilt · 01-01-2013, 08:02 PM

Got any progress pics Bryan?

5150 · 01-01-2013, 09:38 PM

Here are a few Rus, still fighting with the wiring harness and need someone with a few welding skills. Here's a few shots I just took. You can see the button is shaved on the rear and what it looks like inside.

Posted via Mobile Device

Rusbuilt · 01-01-2013, 09:53 PM

Looking good! What are you needing welded?

5150 · 01-01-2013, 11:43 PM

Oh, I need to make a gas door and make two tail lights.
Posted via Mobile Device

Rusbuilt · 01-02-2013, 08:03 AM

Ah ok. I can help with some welding!

5150 · 01-02-2013, 12:34 PM

Well, maybe we can hook up some time soon.
Posted via Mobile Device

Rusbuilt · 01-02-2013, 02:13 PM

Sounds good to me. I need to get up that way to show you that cab I have in Cross Plains anyways.
Posted via Mobile Device

08-18-2012, 07:42 PM	#76
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Project Patina Burb My floor has 4 holes. I'm probably going to put a 3 point harness on one side, like the one I had on my blazer, for my youngest little girl. I'll put a normal 3 point shoulder belt on the other side for my 7 year old. The third row will be factory. __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4 Last edited by 5150; 08-18-2012 at 08:22 PM.

08-18-2012, 08:20 PM	#77
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Project Patina Burb Here's the type of harness I plan on using for my little girl. I figured it would be better then having the shoulder harness stretched across that far over to buckle her in. __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

08-18-2012, 09:11 PM	#78
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,172	Re: Project Patina Burb nice..i like the idea whos truck is that in the pic? __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

08-18-2012, 09:34 PM	#79
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Project Patina Burb That's my old blazer __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

08-18-2012, 09:55 PM	#80
lolife99 67-72 parts collector,… Join Date: Nov 2002 Location: Mid-MO Posts: 22,700	Re: Project Patina Burb Bryan,... did you sell the blazer, or do you still have it? __________________ Keith Convert to disc brakes. http://67-72chevytrucks.com/vboard/s...d.php?t=444823

08-18-2012, 09:58 PM	#82
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Project Patina Burb No, I sold it last October. We had another little girl, Lizzy, last August. Between my small business doing really bad and hospital bills started coming in, I sold it. I didn't miss it until April __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

08-18-2012, 10:01 PM	#83
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Project Patina Burb Looking back at the original post in this thread, you can see the original second row seat that I gave away had the four brackets on the rear. I'll probably use one of them to bolt the 3 point harness to. __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

08-18-2012, 10:20 PM	#84
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Project Patina Burb Here's my hatch that I picked up from the owner of SOKY Classics __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

08-25-2012, 02:23 PM	#85
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Project Patina Burb Got alot of the wiring done on the air ride today. I'm running Slams in the front and the PO gave me these HUGE Goodyear bags that I'm using on the rear. I believe they came from a bus. I also am using the older style Ride Tech Digital Pressure sensor and 4 sensors that I got from smbrouss70. I mounted the tank and the compressor. Also put the valves together with pressure sensors and mounted them in the best locations. Wired everything up, but I don't have a battery in it. I've had it on schrader valves for awhile now. I still have to wire up the switch box and put some 90 degree fittings on the rear, wire up the compressor with relay, and mount the water trap(I just ordered it). __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

09-02-2012, 07:06 PM	#86
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Project Patina Burb okay, finished up the wiring today on the air bags except for wiring up the switch box. I needed a few more connectors. I had some help from my daughter, Halen, who loves to work on it with me. Dropped the drive shaft and got a measurement on how much to shorten it for it to fit the 4L60E. __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

09-04-2012, 08:57 PM	#87
502ms Registered User Join Date: Aug 2011 Location: Atlanta, GA Posts: 1,523	Re: Project Patina Burb Very nice! Posted via Mobile Device __________________ Best Regards, Leon M. Instagram: @TheDirtyDianah Bagged \| 6.0L LS \| T-56 (6-Speed Manual) \| Turbo Burnout/Rolling Video: Chevy C10 Stepside 6.0L LSx & 6-Speed Manual

09-27-2012, 02:34 AM	#88
oldblue1968chevy Grandpa in the rustmobile... Join Date: Nov 2008 Location: Spokane WA/Viola TN Posts: 11,422	Re: Project Patina Burb I think I have you on FB Are you bryan? Anyways, cool build Im following along. __________________ John Goose-1968 C10 355,9.32-1CR, Vortec Heads ,262 voodoo, 3.73:1 3OTT (HS ride/beater/farm truck) http://67-72chevytrucks.com/vboard/s...d.php?t=317684 Grams 53-1953 Chevrolet Belair http://67-72chevytrucks.com/vboard/s...=1#post4327784 1969 Chevy C10 Shortbed 4.5/6?" Frame off resto http://67-72chevytrucks.com/vboard/s...d.php?t=548136 1999 Toyota Tacoma 4x4

11-10-2012, 09:54 PM	#89
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Project Patina Burb Got most of the fuel line ran today. Still have to install the tank, but all the line has been ran to the rear of the burb. __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

11-29-2012, 08:15 PM	#90
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Project Patina Burb Got the tank in and wired up. Got it off jack stands for the first time in a couple of months. Still messing with the new wiring harness. It's an 21 circuit EZ Wiring harness and it's a bit overwhelming to say the least. Posted via Mobile Device __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

12-31-2012, 12:28 PM	#91
jeffg1010 Registered User Join Date: Aug 2010 Location: Mooresville, NC Posts: 2,677	Re: Project Patina Burb Subscribed. Cant wait to see it on the Power Tour Posted via Mobile Device __________________ Jeff 1972 Blazer CST 2wd- My son Sam's Project "S" Project "S" 1970 Suburban - SOLD "One Bad Burb" Photobucket Album 1986 C30 Crewcab - 63K original miles, original paint Members I have met: mikey531, gcburdic, bashed, burbman69, TonyPieras, Blazester, GCncsuHD, custombuilt67-72, tsnow678, highrpm, PanelDeland, tanman722001, 47thriftmaster, babyblueoval, 68stepbed, JesseWebb, Andy4639, xs-style, TobyArnot, BigOrange, frednoah, brn_agn, k5hart, Graham57a, bhelton, AJohn6, SilverC10, 69CST, '71 Flame, RaceAGMC, Liz, Josh, MattPSU, 68corvair, Chevy350V8, mdeal, ccrorymc, mrhurt73, dmxxpert, Custom68, 84GMC, BionicABs1, BigBlockBurris, Ebfabman, ATP...



Register or Log In To remove these advertisements.

01-01-2013, 06:19 PM	#92
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Project Patina Burb Got a few things done today. I got my carpet kit in from Brother's this week also. I'm kind of collecting parts as of late. Cleaned up some of the metal interior trip today with the bench grinder. I slapped the wire wheel attachment on it and cleaned most of the surface rust that was on them. __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

01-01-2013, 06:30 PM	#93
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Project Patina Burb I also saw another problem I'm going to have to deal with due to the PO shaving certain things. I have a good hatch, but the push button has been shaved so I'm not sure how I'm going to get it open from the outside. __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

01-01-2013, 08:02 PM	#94
Rusbuilt Registered User Join Date: Mar 2012 Location: Knoxville, TN Posts: 5,381	Re: Project Patina Burb Got any progress pics Bryan? __________________ -Rus PLEASE HELP WITH PROJECT UNDERHAULINPaypal donations accepted @ rus1785@yahoo.com Rusbuilt's garage 1968 Chevy C-30 Darcy SOLD Rusbuilt shop truck *SOLD*

01-01-2013, 09:38 PM	#95
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Project Patina Burb Here are a few Rus, still fighting with the wiring harness and need someone with a few welding skills. Here's a few shots I just took. You can see the button is shaved on the rear and what it looks like inside. Posted via Mobile Device __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

01-01-2013, 09:53 PM	#96
Rusbuilt Registered User Join Date: Mar 2012 Location: Knoxville, TN Posts: 5,381	Re: Project Patina Burb Looking good! What are you needing welded? __________________ -Rus PLEASE HELP WITH PROJECT UNDERHAULINPaypal donations accepted @ rus1785@yahoo.com Rusbuilt's garage 1968 Chevy C-30 Darcy SOLD Rusbuilt shop truck *SOLD*

01-01-2013, 11:43 PM	#97
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Project Patina Burb Oh, I need to make a gas door and make two tail lights. Posted via Mobile Device __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

01-02-2013, 08:03 AM	#98
Rusbuilt Registered User Join Date: Mar 2012 Location: Knoxville, TN Posts: 5,381	Re: Project Patina Burb Ah ok. I can help with some welding! __________________ -Rus PLEASE HELP WITH PROJECT UNDERHAULINPaypal donations accepted @ rus1785@yahoo.com Rusbuilt's garage 1968 Chevy C-30 Darcy SOLD Rusbuilt shop truck *SOLD*

01-02-2013, 12:34 PM	#99
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Project Patina Burb Well, maybe we can hook up some time soon. Posted via Mobile Device __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

01-02-2013, 02:13 PM	#100
Rusbuilt Registered User Join Date: Mar 2012 Location: Knoxville, TN Posts: 5,381	Re: Project Patina Burb Sounds good to me. I need to get up that way to show you that cab I have in Cross Plains anyways. Posted via Mobile Device __________________ -Rus PLEASE HELP WITH PROJECT UNDERHAULINPaypal donations accepted @ rus1785@yahoo.com Rusbuilt's garage 1968 Chevy C-30 Darcy SOLD Rusbuilt shop truck *SOLD*

Register or Log In To remove these advertisements.