Eric's 1966 Turbo 6.0 build - Page 4 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

bocephus79 · 02-14-2020, 10:20 AM

SO this Is less Fun Than I Imagined. More stressful than hard, Trying to get it perfect.

bocephus79 · 02-15-2020, 06:31 PM

So After we got some stuff in paint and clear today, it's apparent I need to re visit my exhaust fan situation. I may do something more permanent because I'm sure I'll be painting something again in the future

joesscamaro · 02-16-2020, 08:52 AM

Nice looking color! That wiring situation makes me want to avoid that on my truck, haha.

bocephus79 · 02-16-2020, 04:51 PM

Quote:

Originally Posted by joesscamaro

Nice looking color! That wiring situation makes me want to avoid that on my truck, haha.

Thanks!
I'm Probably making it harder than it needs to be by routing stuff in ways to hide it as much as possible. I also have to build a separate fuse panel/ relay panel for the Holley terminator and fuel pumps and stuff.

bocephus79 · 03-02-2020, 12:14 PM

After Painting the fenders and cab pieces, we realized the current fan situation wasn't going to work anymore. So I made a more permanent soulution.

bocephus79 · 05-18-2020, 06:51 PM

Progress:
90% wired
Had doors painted in the booth with my new exhaust setup, worked great!
Exhaust mocked up complete with boost activated cutout

**Android04** · 05-18-2020, 08:35 PM

Looks killer!

So do the actuators on the cut outs open only under positive pressure? Never seen that, so would you just wire it in to a vacuum source or a boost source off the wastegate?

bocephus79 · 05-19-2020, 09:51 AM

Quote:

Originally Posted by Android04

Looks killer!

So do the actuators on the cut outs open only under positive pressure? Never seen that, so would you just wire it in to a vacuum source or a boost source off the wastegate?

Boost Actuated. Fully open around 10psi. We will see how it goes, but I know that 6 feet of pipe loses significant HP in a turbo downpipe ( Per SLoppymechanics)

**Android04** · 05-19-2020, 10:16 AM

Quote:

Originally Posted by bocephus79

Boost Actuated. Fully open around 10psi. We will see how it goes, but I know that 6 feet of pipe loses significant HP in a turbo downpipe ( Per SLoppymechanics)

Very unique and curious to see how it works. So I'm assuming you would tune with the cut out's open. Tend to see a decent Air/Fuel difference with full exhaust compared to just a downpipe.

Love the build and can't wait to see more.

88Stanger · 05-19-2020, 01:14 PM

Damn fine build so far!! Love this.

tinydb84 · 05-19-2020, 02:43 PM

I'm sure you already looked into it but make sure that fan is rated for that. Plenty of fires and explosions have happened from using the wrong style of fan when painting.

bocephus79 · 05-19-2020, 04:09 PM

Quote:

Originally Posted by tinydb84

I'm sure you already looked into it but make sure that fan is rated for that. Plenty of fires and explosions have happened from using the wrong style of fan when painting.

Yeah It's a "fire" rated fan TEFC motor so it worked out that I had it laying around

bocephus79 · 07-14-2020, 11:53 AM

Some progress over the last few weeks.
Bed and tailgate painted
Engine primed with a garden sprayer
tedious interior install

and oh yeah, this happened https://youtu.be/vHHoEYXs7Uk

aggie91 · 07-14-2020, 12:00 PM

Nice!

**Android04** · 07-24-2020, 10:14 AM

Love it.

88Stanger · 07-25-2020, 09:54 PM

fantastic work sir

aggie91 · 07-28-2020, 10:51 AM

What radio did you go with in the dash?

88Stanger · 07-31-2020, 10:06 AM

Nice Job Sir!! i am almost at the point that i need to start a paint booth like you got. nice work.

Wizit247 · 08-04-2020, 05:54 PM

wow is all I have to say! Im following!

bocephus79 · 09-01-2020, 09:35 AM

Some Progress Updates. Most of the interior is done, at least the hard parts I wanted to do before the doors were installed.
the new door handles seem too " short" The actuator pin on the push button needs to be like 1/8 longer to make the latch open all the way.

As far as the bed wood kit from Mark-k goes..I wanted the bed on the truck so when I mock the wood up to drill the holes everything is perfect. Man was setting that thing on the frame stressful

aggie91 · 09-01-2020, 10:56 AM

Nice progress. Love that blue.

88Stanger · 09-03-2020, 09:30 AM

looking awesome!

LostMy65 · 09-03-2020, 03:28 PM

Looking really good.

bocephus79 · 09-09-2020, 11:20 AM

Test fit of the boards so I can mark the outside edge holes to drill and the gas tank fill

88Stanger · 09-09-2020, 12:18 PM

Where did you get the seat?

Jeff

02-14-2020, 10:20 AM	#76
bocephus79 Registered User Join Date: Jul 2016 Location: Cleveland Ohio Posts: 67	Re: Eric's 1966 Turbo 6.0 build SO this Is less Fun Than I Imagined. More stressful than hard, Trying to get it perfect. Attached Images

02-15-2020, 06:31 PM	#77
bocephus79 Registered User Join Date: Jul 2016 Location: Cleveland Ohio Posts: 67	Re: Eric's 1966 Turbo 6.0 build So After we got some stuff in paint and clear today, it's apparent I need to re visit my exhaust fan situation. I may do something more permanent because I'm sure I'll be painting something again in the future Attached Images

02-16-2020, 08:52 AM	#78
joesscamaro Registered User Join Date: Sep 2008 Location: Newport, North Carolina Posts: 638	Re: Eric's 1966 Turbo 6.0 build Nice looking color! That wiring situation makes me want to avoid that on my truck, haha.

03-02-2020, 12:14 PM	#80
bocephus79 Registered User Join Date: Jul 2016 Location: Cleveland Ohio Posts: 67	Re: Eric's 1966 Turbo 6.0 build After Painting the fenders and cab pieces, we realized the current fan situation wasn't going to work anymore. So I made a more permanent soulution. Attached Images

05-18-2020, 06:51 PM	#81
bocephus79 Registered User Join Date: Jul 2016 Location: Cleveland Ohio Posts: 67	Re: Eric's 1966 Turbo 6.0 build Progress: 90% wired Had doors painted in the booth with my new exhaust setup, worked great! Exhaust mocked up complete with boost activated cutout Attached Images

05-18-2020, 08:35 PM	#82
Android04 Senior Member Join Date: Aug 2017 Location: Louisville, KY Posts: 376	Re: Eric's 1966 Turbo 6.0 build Looks killer! So do the actuators on the cut outs open only under positive pressure? Never seen that, so would you just wire it in to a vacuum source or a boost source off the wastegate?

05-19-2020, 01:14 PM	#85
88Stanger Registered User Join Date: Mar 2015 Location: Washington State Posts: 1,651	Re: Eric's 1966 Turbo 6.0 build Damn fine build so far!! Love this.

05-19-2020, 02:43 PM	#86
tinydb84 Registered User Join Date: Jul 2009 Location: San Jose Ca Posts: 2,871	Re: Eric's 1966 Turbo 6.0 build I'm sure you already looked into it but make sure that fan is rated for that. Plenty of fires and explosions have happened from using the wrong style of fan when painting. __________________ David Used parts build: http://67-72chevytrucks.com/vboard/s...d.php?t=638991 My brother's Nova: http://www.67-72chevytrucks.com/vboa...d.php?t=727985 Rear suspension rework: http://www.67-72chevytrucks.com/vboa...d.php?t=750557 Instagram: myfabguy

07-14-2020, 11:53 AM	#88
bocephus79 Registered User Join Date: Jul 2016 Location: Cleveland Ohio Posts: 67	Re: Eric's 1966 Turbo 6.0 build Some progress over the last few weeks. Bed and tailgate painted Engine primed with a garden sprayer tedious interior install and oh yeah, this happened https://youtu.be/vHHoEYXs7Uk Attached Images

07-14-2020, 12:00 PM	#89
aggie91 I'm just glad to be here! Join Date: Jan 2008 Location: Longview, TX Posts: 4,788	Re: Eric's 1966 Turbo 6.0 build Nice! __________________ Karl 1965 Chevy Stepside(Grandpa's Old Blue) and (July 2015 Shop Build!)(2020, the Saga Continues) http://67-72chevytrucks.com/vboard/s...d.php?t=372424 The LST Challenge: http://67-72chevytrucks.com/vboard/s...=1#post7812257 Korbin's 1st Square: "Sunburn" http://67-72chevytrucks.com/vboard/s...d.php?t=418618 1985 GMC Sierra: "White Trash", Korbin's 2nd now... http://67-72chevytrucks.com/vboard/s...d.php?t=632305 Henry - 1984 Chevrolet, Owen's 1st Square

07-24-2020, 10:14 AM	#90
Android04 Senior Member Join Date: Aug 2017 Location: Louisville, KY Posts: 376	Re: Eric's 1966 Turbo 6.0 build Love it.

07-25-2020, 09:54 PM	#91
88Stanger Registered User Join Date: Mar 2015 Location: Washington State Posts: 1,651	Re: Eric's 1966 Turbo 6.0 build fantastic work sir

07-28-2020, 10:51 AM	#92
aggie91 I'm just glad to be here! Join Date: Jan 2008 Location: Longview, TX Posts: 4,788	Re: Eric's 1966 Turbo 6.0 build What radio did you go with in the dash? __________________ Karl 1965 Chevy Stepside(Grandpa's Old Blue) and (July 2015 Shop Build!)(2020, the Saga Continues) http://67-72chevytrucks.com/vboard/s...d.php?t=372424 The LST Challenge: http://67-72chevytrucks.com/vboard/s...=1#post7812257 Korbin's 1st Square: "Sunburn" http://67-72chevytrucks.com/vboard/s...d.php?t=418618 1985 GMC Sierra: "White Trash", Korbin's 2nd now... http://67-72chevytrucks.com/vboard/s...d.php?t=632305 Henry - 1984 Chevrolet, Owen's 1st Square

07-31-2020, 10:06 AM	#93
88Stanger Registered User Join Date: Mar 2015 Location: Washington State Posts: 1,651	Re: Eric's 1966 Turbo 6.0 build Nice Job Sir!! i am almost at the point that i need to start a paint booth like you got. nice work.

08-04-2020, 05:54 PM	#94
Wizit247 Registered User Join Date: Jun 2015 Location: North Idaho Posts: 99	Re: Eric's 1966 Turbo 6.0 build wow is all I have to say! Im following! __________________ Over the top, billet infused, ground up 60 GMC build http://6772chevytrucks.com/vboard/showthread.php?t=809901



Register or Log In To remove these advertisements.

09-01-2020, 09:35 AM	#95
bocephus79 Registered User Join Date: Jul 2016 Location: Cleveland Ohio Posts: 67	Re: Eric's 1966 Turbo 6.0 build Some Progress Updates. Most of the interior is done, at least the hard parts I wanted to do before the doors were installed. the new door handles seem too " short" The actuator pin on the push button needs to be like 1/8 longer to make the latch open all the way. As far as the bed wood kit from Mark-k goes..I wanted the bed on the truck so when I mock the wood up to drill the holes everything is perfect. Man was setting that thing on the frame stressful Attached Images

09-01-2020, 10:56 AM	#96
aggie91 I'm just glad to be here! Join Date: Jan 2008 Location: Longview, TX Posts: 4,788	Re: Eric's 1966 Turbo 6.0 build Nice progress. Love that blue. __________________ Karl 1965 Chevy Stepside(Grandpa's Old Blue) and (July 2015 Shop Build!)(2020, the Saga Continues) http://67-72chevytrucks.com/vboard/s...d.php?t=372424 The LST Challenge: http://67-72chevytrucks.com/vboard/s...=1#post7812257 Korbin's 1st Square: "Sunburn" http://67-72chevytrucks.com/vboard/s...d.php?t=418618 1985 GMC Sierra: "White Trash", Korbin's 2nd now... http://67-72chevytrucks.com/vboard/s...d.php?t=632305 Henry - 1984 Chevrolet, Owen's 1st Square

09-03-2020, 09:30 AM	#97
88Stanger Registered User Join Date: Mar 2015 Location: Washington State Posts: 1,651	Re: Eric's 1966 Turbo 6.0 build looking awesome!

09-03-2020, 03:28 PM	#98
LostMy65 But Found Her 25yrs Later! Join Date: Oct 2010 Location: Oregon City, Oregon Posts: 10,528	Re: Eric's 1966 Turbo 6.0 build Looking really good. __________________ I lost my 65 - Found it 25 years later: http://67-72chevytrucks.com/vboard/s...d.php?t=426650 66 C20 Service Truck: http://67-72chevytrucks.com/vboard/s...d.php?t=428035

09-09-2020, 11:20 AM	#99
bocephus79 Registered User Join Date: Jul 2016 Location: Cleveland Ohio Posts: 67	Re: Eric's 1966 Turbo 6.0 build Test fit of the boards so I can mark the outside edge holes to drill and the gas tank fill Attached Images

09-09-2020, 12:18 PM	#100
88Stanger Registered User Join Date: Mar 2015 Location: Washington State Posts: 1,651	Re: Eric's 1966 Turbo 6.0 build Where did you get the seat? Jeff

Register or Log In To remove these advertisements.