![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#76 | |
Senior Member
Join Date: Jul 2005
Location: Winters Ca. 95694
Posts: 4,843
|
Re: LFD's upper door seal idea!
Quote:
Kevin LFD Inc. |
|
![]() |
![]() |
![]() |
#77 |
Registered User
Join Date: Feb 2009
Location: arroyo grande, ca
Posts: 206
|
Re: LFD's upper door seal idea!
Kevin,
This may be a bit off topic, but I feel you are the best to answer this question because of all your experimenting. I bought some seals for the doors form Steele Rubber Products upon request of my body man, and once they were installed, my doors will hardly close. I know this may be normal, but the amount of effort that it takes to close the door leaves me feeling I am going to dent the door where the handle mounts to the door itself (exterior) with such required force. I did not measure the gap between the door sealing surface and the lip on the cab, but they look uniform all the way around on the passenger side and slightly off on the driver side. I would say they are close to 3/16". Is this normal? I will get down the the body shop on Monday and measure if this helps answer. Is there a better seal to purchase that is not quite so "fat" allowing the door to not be damaged? Again I didn't measure the uncompressed thickness of the seal, but it is much much larger than the gap, more so than I believe it should be. I installed some door seals on my early bronco some years back and the doors seemed hard to close, but nothing like this; and after a month or two, they shut just fine and I never worried about it again. By the way, I purchased a set of your new seals and they are in transit and I was just getting ready to install them once they arrived. I am looking forward to having a "like new" old pickup. Thanks James
__________________
James |
![]() |
![]() |
![]() |
#78 |
Senior Member
Join Date: Jul 2005
Location: Winters Ca. 95694
Posts: 4,843
|
Re: LFD's upper door seal idea!
Are the seals that you have already put in stock seals from SRC or are they a different style? I know a lot of guys use buy 73 up and they are bigger and cause problems. Are yours glue on or push on? I have always got mine from LMC or ECE and they are the stock glue on and work fine (but leak
![]() Kevin LFD Inc. |
![]() |
![]() |
![]() |
#79 |
Registered User
Join Date: Feb 2009
Location: arroyo grande, ca
Posts: 206
|
Re: LFD's upper door seal idea!
They are the glue on. I made sure they were the correct p/n and talked to the rep. They say I can send them back and get new ones, but I don't see what that would change...I may check out ECE.
__________________
James |
![]() |
![]() |
![]() |
#80 | |
Senior Member
Join Date: Jul 2005
Location: Winters Ca. 95694
Posts: 4,843
|
Re: LFD's upper door seal idea!
Quote:
Kevin LFD Inc. |
|
![]() |
![]() |
![]() |
#81 |
Senior Member
Join Date: Jul 2005
Location: Winters Ca. 95694
Posts: 4,843
|
Re: LFD's upper door seal idea!
Hey guys I just got confirmation that the product has shipped to me so I should have it in the next few days and will ship out the first 18 sets asap.
Kevin LFD Inc. |
![]() |
![]() |
![]() |
#82 |
Registered User
Join Date: Feb 2009
Location: arroyo grande, ca
Posts: 206
|
Re: LFD's upper door seal idea!
Thanks Kevin for all your help, sorry for forcing in on your thread.
James.
__________________
James |
![]() |
![]() |
![]() |
#83 |
Registered User
Join Date: Dec 1999
Location: Santee Ca
Posts: 251
|
Re: LFD's upper door seal idea!
I will take a set. Payment sent Thanks
|
![]() |
![]() |
![]() |
#84 |
Senior Member
Join Date: Jul 2005
Location: Winters Ca. 95694
Posts: 4,843
|
Re: LFD's upper door seal idea!
First 18 are shipping out in the morning, cut, instructions, boxed and labeled! Should have the second batch in a few days and 2 days after that they will be on their way out.
Kevin LFD Inc. [IMG] ![]() |
![]() |
![]() |
![]() |
#85 |
Senior Member
Join Date: Aug 2002
Location: Valley Center KS
Posts: 3,525
|
Re: LFD's upper door seal idea!
I'll have to get a set of these in a month or two when I get closer to getting on the road.
Since I shaved the drip rail, this may also prevent water getting in too (a concern of one of the body guys I talked to before it was painted) |
![]() |
![]() |
![]() |
#86 | |
Senior Member
Join Date: Jul 2005
Location: Winters Ca. 95694
Posts: 4,843
|
Re: LFD's upper door seal idea!
Quote:
Kevin LFD Inc. |
|
![]() |
![]() |
![]() |
#87 |
Senior Member
Join Date: Jul 2005
Location: Winters Ca. 95694
Posts: 4,843
|
Re: LFD's upper door seal idea!
Ok I got the call this morning and the second order is on it's way and should be here by the weekend. All out standing orders will ship out Monday (assuming it shows here on time) and I will have enough for about 6-10 more kits. This may be the last order at the current price as I was informed my cost will go up on the next order so if you want the lower cost (for the next 10 orders) order off this batch as the next order would be $10 more on trucks and $20 on the burbs (lost money on the current price) if the prices go up like I was told.
Kevin LFD Inc. |
![]() |
![]() |
![]() |
#88 |
Registered User
Join Date: Nov 2001
Location: Springfield, MO
Posts: 2,932
|
Re: LFD's upper door seal idea!
Kevin, I am still on the list for this next order correct?
Thanks Dave in Missouri
__________________
Dave 1968 Custom Chevy with turbo charged 5.3 gen III 4l80e swap 1967-71 GMC 3/4 ton long step 4x4 (not sure what year exactly?) "A good friend will bail you out of jail...but a true friend will be sitting next to you saying "that was frekin awesome". "If it doesn't fit force it...If it breaks then it needed to be replaced anyway!" |
![]() |
![]() |
![]() |
#89 | |
Senior Member
Join Date: Jul 2005
Location: Winters Ca. 95694
Posts: 4,843
|
Re: LFD's upper door seal idea!
Quote:
Kevin LFD Inc. |
|
![]() |
![]() |
![]() |
#90 |
Senior Member
![]() Join Date: Dec 1999
Location: New Palestine, IN
Posts: 470
|
Re: LFD's upper door seal idea!
Kevin
You mentioned about the adhesive being nice and fresh. I need to do two trucks, but I know I won't be putting the seals on for a year maybe two. Do you think the seals will still stick okay after that long of time? Mark
__________________
72 Shortbed fleetside 402 BB, AC, Posi 72 Super Cheyenne Longbed 350 49,000 original miles and My dad ordered it new 66 Chevy Caprice 2 dr 77 Caprice Estate Wagon New Palestine, IN |
![]() |
![]() |
![]() |
#91 | |
Senior Member
Join Date: Jul 2005
Location: Winters Ca. 95694
Posts: 4,843
|
Re: LFD's upper door seal idea!
Quote:
Kevin LFD Inc. |
|
![]() |
![]() |
![]() |
#92 |
Senior Member
Join Date: Jul 2005
Location: Winters Ca. 95694
Posts: 4,843
|
Re: LFD's upper door seal idea!
Ok every order that was received as of today is boxed and in the mail! If for some reason someone does not receive their in about a week let me know.
So have any of the first orders been installed yet and if so what do you think? Every time I get in my truck I can not believe the difference but now the little bit of noise I get from my vent windows is bugging me but not enough to go 1 pc! I have never opened my vents since the day I put them in and never plan on doing so. What I might do is open them up and clean everything real well then put a small bead of silicone on the seals and shut them for good and see what difference that makes. I still do want to add power windows and then I think it will be complete. I want to thank everyone who has ordered and wish the entire site a Merry Christmas! Kevin LFD Inc. Last edited by Rokcrln; 12-22-2009 at 12:23 AM. |
![]() |
![]() |
![]() |
#93 |
Senior Member
Join Date: Nov 2004
Location: Vacaville, CA
Posts: 2,272
|
Re: LFD's upper door seal idea!
Will give you a call tomorrow hopefully to come over with the orange truck.
|
![]() |
![]() |
![]() |
#94 |
Senior Member
Join Date: Jul 2005
Location: Winters Ca. 95694
Posts: 4,843
|
Re: LFD's upper door seal idea!
Sounds good you saved me a call
![]() Kevin LFD Inc. |
![]() |
![]() |
![]() |
#95 |
Registered User
Join Date: Dec 2009
Location: Boonville, MO
Posts: 26
|
Re: LFD's upper door seal idea!
What I might do is open them up and clean everything real well then put a small bead of silicone on the seals and shut them for good and see what difference that makes.
Please let us know how this works, I haven't started building my truck, but am looking at all the information I can before I start. Wind noise was something that I knew was going to bother me alot. Why not make 'em like a new truck, just with alot more style? |
![]() |
![]() |
![]() |
#96 | |
Registered User
Join Date: Nov 2001
Location: Springfield, MO
Posts: 2,932
|
Re: LFD's upper door seal idea!
Quote:
Dave
__________________
Dave 1968 Custom Chevy with turbo charged 5.3 gen III 4l80e swap 1967-71 GMC 3/4 ton long step 4x4 (not sure what year exactly?) "A good friend will bail you out of jail...but a true friend will be sitting next to you saying "that was frekin awesome". "If it doesn't fit force it...If it breaks then it needed to be replaced anyway!" |
|
![]() |
![]() |
![]() |
#97 |
Senior Member
![]() Join Date: Aug 2008
Location: Cedar Park, Texas
Posts: 7,496
|
Re: LFD's upper door seal idea!
Same problem here. Currently no wind noise problem, as no engine in truck!
Last edited by WIDESIDE72; 12-24-2009 at 11:00 AM. |
![]() |
![]() |
![]() |
#98 |
Registered User
Join Date: Aug 2007
Location: Bakersfield, Ca
Posts: 538
|
![]()
Well dummy me, I missplaced the instructions but thought I remembered how they went. Anyway, found the instructions today and saw I couldn't of done it more wrong. Door seal on cab, cab on doors... put the seal on the cab closer to the original seal instead of the more outer lip.
Hard to believe but it worked great anyway. Though this morning I noticed the seals on the cab seperating due to being squished with the sticky side being pulled away (it's not being squished towards the sticky side if you know what I mean). So this jerk will order another set and try again because it does make a big difference. The only problem I can see is that my doors, probably like many others, doesn't match the cab perfectly (the doors latch smoothly and looks good down the side). Mine have a pretty big gap at the top, the correct spot to glue the rubber to the cab will likely be seen when the door is closed if you have the same fit as me. Last edited by Mondo; 01-24-2010 at 02:05 PM. |
![]() |
![]() |
![]() |
#99 |
Registered User
Join Date: Dec 2009
Location: Hickory Creek, TX
Posts: 4
|
Re: LFD's upper door seal idea!
Sent payment today
|
![]() |
![]() |
![]() |
#100 |
Senior Member
Join Date: Jul 2005
Location: Winters Ca. 95694
Posts: 4,843
|
Re: LFD's upper door seal idea!
Mondo, Joseph H and Mark L. Yours is on it's way as of today!
Thanks guys Kevin LFD Inc. |
![]() |
![]() |
![]() |
Bookmarks |
|
|