|
03-18-2010, 12:02 AM
|
#76 |
|
Account Suspended
Join Date: Jun 2009
Posts: 269
|
Custom 1987 GMC Crew Cab Short Bed
Just a few more...
|
|
|
03-18-2010, 12:04 AM
|
#77 |
|
Account Suspended
Join Date: Jun 2009
Posts: 269
|
Custom 1987 GMC Crew Cab Short Bed
last few...
|
|
|
|
03-18-2010, 12:42 AM
|
#78 |
|
Account Suspended
Join Date: Jun 2009
Posts: 269
|
Custom 1987 GMC Crew Cab Short Bed
The remedy...
After taking a number of measurements I discovered that the rear axle center line was between 5 3/4" - 6" to far forward, and needed to be brought back. After unbolting the rear leaf spring shackle hanger I found that the difference in measure between the two vertical sets of mounting holes was very close to the distance I needed to move the axle back. In order to insure that the suspension would remain square to the chassis I decided to reuse the two rear mounting holes on the chassis to the two front mounting holes on the shackle hanger. As for the front leaf spring hangers I discovered that the distance between the two lower chassis mount holes where 6 1/4" apart. I thought to myself how much I would be able to tell having the axle center line back 1/4" from exact wheel well center? After determining that I more than likely will not notice any real difference in 1/4" I went for it. I scribed a line over the top of the two lower chassis mounting holes for the front leaf spring hanger all the way back until I ran the scribe off the end of the chassis. Once I reattached the front lower leaf spring hanger mounting hole to the rear mounting hole on the chassis, I adjusted the angle of the hanger until the top of the lower rear hanger mounting hole was in line with my scribe line. At that point I tightened the bolt down so the hanger would not move out of adjustment. I drilled out the two top chassis mounting holes through the existing hanger mounting holes, and then drilled a new mounting hole through both hanger and chassis about 3" above the existing rear lower hanger mounting hole. *Note the two bottom holes on the hanger bolt to a separate bracket, and not the chassis. The lower bracket required a little fabrication to be reused. After I had fully assembled the front leaf spring hangers to the chassis, I attached the lower bracket to the hanger. Because I moved the hangers back 6 1/4" the angle of the chassis has changed (Chassis kickup), and the lower bracket no longer fits the way it should. While the lower bracket was attached to the hanger I could build a wedge into the bracket that would fill the gap between the chassis and bracket. I used construction paper to make my templates, and then cut out the final pieces from 1/4" flat stock. After welding everything up, I test fit my new bracket(s), and everything looked, and should work great! Other parts I moved: Shock mounts, brake line bracket, bump stops (Yet to be installed), and the parking brake cable guide bracket. All in all I am very happy with the way it all turned out. Tomorrow I will be installing the gas tanks, and bump stops. If I have time I will refit the bed to see how it all looks. Oh yeah...I didn't paint the brake shoe backing plates because I have plans to convert to discs. 
|
|
|
|
03-18-2010, 09:38 AM
|
#79 |
|
Registered User
Join Date: Mar 2003
Location: wichita falls tx
Posts: 429
|
Re: Custom 1987 GMC Crew Cab Short Bed
Measure twice. Cut once.
|
|
|
|
03-18-2010, 03:26 PM
|
#80 |
|
Account Suspended
Join Date: Jun 2009
Posts: 269
|
Custom 1987 GMC Crew Cab Short Bed
I don't know if you actually read my last Post, but I clearly stated that I didn't measure the two different beds at all.
I As! U Med. I did measure the length difference of the short bed leading bed mount to the trailing bed mount. The bed fits the chassis perfectly, I just should have cut a little less up front, taken a little from the back, and drilled new bed mount holes. That would have been easier than moving the entire suspension... Live and learn... As long as you learn from your mistakes, and can be man enough to admit when you are wrong, then you'll be all right! I am not looking for comments of what I should have done differently, I have already figured that out... But thank you nonetheless. |
|
|
|
03-18-2010, 08:19 PM
|
#81 |
|
Account Suspended
Join Date: Jun 2009
Posts: 269
|
Custom 1987 GMC Crew Cab Short Bed
Test fit bed...
Axle Centerline is fixed |
|
|
|
03-18-2010, 08:23 PM
|
#82 |
|
Account Suspended
Join Date: Jun 2009
Posts: 269
|
Custom 1987 GMC Crew Cab Short Bed
I tried fitting the factory fuel tanks in today, and there is no way to make them work unless I drop the hangers. If I do that, the tanks are to visible (Not an option).
 I am going to pickup a set of 1/2 short bed tanks today or tomorrow (Still waiting to hear from the guy who has a set) and see if those will work. The 1/2 ton tanks are 4 gallons smaller (Each) which is kind of a bummer, but once I have this truck running at 20 MPG, I don't think it will be as big of a problem. More soon to come! |
|
|
|
03-18-2010, 09:56 PM
|
#83 |
|
Registered User
Join Date: Apr 2009
Location: Waynesfield Ohio
Posts: 1,991
|
Re: Custom 1987 GMC Crew Cab Short Bed
looks like everything turned out fine
__________________
 1949 Five Window, 1973 Step Side, 2000 Z71 |
|
|
|
03-19-2010, 12:22 AM
|
#84 |
|
Account Suspended
Join Date: Jun 2009
Posts: 269
|
Re: Custom 1987 GMC Crew Cab Short Bed
It's confirmed... I'll be getting the 1/2 ton short bed tanks tomorrow...$0
|
|
|
|
03-19-2010, 09:17 AM
|
#85 |
|
Registered User
Join Date: Dec 2008
Location: Silverhill, Al
Posts: 2,026
|
Re: Custom 1987 GMC Crew Cab Short Bed
sweet free is always good!
__________________
Fuzzy Dice Club Member 87 Crew SWB Build for the crew http://67-72chevytrucks.com/vboard/s...d.php?t=430082 http://www.cardomain.com/ride/3232925 90 burb 2wd Build Thread For The Burb! http://67-72chevytrucks.com/vboard/s...d.php?t=383055 |
|
|
|
03-29-2010, 11:50 PM
|
#86 |
|
Account Suspended
Join Date: Jun 2009
Posts: 269
|
Re: Custom 1987 GMC Crew Cab Short Bed
Oh boy! you guys will never guys what I just bought for this project...
Chevy Dana 60 front axle with a box containing a complete new rebuild kit for axle... Hydro Assist steering High steer / cross over steering (Brand new) All new tie rod ends Brand New polished aluminum diff cover drop pitman arm for 2wd Steering box Rebuilt 2wd steering box 14 Bolt FF rear axle New bearings and seals New Disc brake conversion New polished aluminum diff cover! and I should be getting my custom built aluminum radiator with electronically controlled electric fan any day This truck is going to be insane! I'll have photos soon... Our female American bull dogs is about to have puppies any day, so my wife and I have been busy getting ready... |
|
|
|
03-29-2010, 11:51 PM
|
#87 |
|
Account Suspended
Join Date: Jun 2009
Posts: 269
|
Custom 1987 GMC Crew Cab Short Bed
Here are our babies...
|
|
|
|
03-29-2010, 11:52 PM
|
#88 |
|
Account Suspended
Join Date: Jun 2009
Posts: 269
|
Re: Custom 1987 GMC Crew Cab Short Bed
needless to say, my wife and my son have nothing to worry about while I'm not home...
|
|
|
|
03-29-2010, 11:54 PM
|
#89 |
|
Account Suspended
Join Date: Jun 2009
Posts: 269
|
Re: Custom 1987 GMC Crew Cab Short Bed
Oh yeah... My male American Bulldog's name is "Diesel." He is 124 lbs. I could have just as easily named him 6.2... ha ha!
|
|
|
|
03-30-2010, 12:00 AM
|
#90 |
|
Account Suspended
Join Date: Jun 2009
Posts: 269
|
Re: Custom 1987 GMC Crew Cab Short Bed
Wow... Seems I keep forgetting things... The axles are 4.10's and I have just bought my 3rd fleet side short bed. I think I am happy with the one I have now, but only time will tell.
The last bed I bought came with two nice 1/2 ton 16 gallon fuel tanks. After I finish my land cruiser project (Customer's truck). I'll be wrapping up most of the initial build requirements for the crew cab. Once the truck is fully put together, I will completely disassemble it for chassis powder coating, body, paint and upholstery... |
|
|
|
05-11-2010, 03:55 AM
|
#91 |
|
Account Suspended
Join Date: Jun 2009
Posts: 269
|
Re: Custom 1987 GMC Crew Cab Short Bed
I just bought a 2007 Dodge 1 Ton 4X4 Roll over truck with only 42,000 miles! Oh yeah, it has a cummins and a 6 speed manual trans! Can you say 650 FT of Torque baby!
The 6.2 was going to be turbo charged with a custom built NV4500... After comparing the price it would cost to build a 6.2 with that setup, it seemed more reasonable just to put in a Donor 24V Cummins... I'll post photos in the next day or so... Stay tuned.... One of the BADDEST CREW CAB SHORT BED BUILDS.... |
|
|
|
05-11-2010, 01:40 PM
|
#92 |
|
Garage wrench
Join Date: Feb 2008
Location: LaCrosse, WI
Posts: 1,855
|
Re: Custom 1987 GMC Crew Cab Short Bed
very cool update, this truck will be awesome
__________________
-Adam 90 V1500 GMC Suburban 350/700R4/NP241..... 01 Saturn SL1 stock DD..... |
|
|
|
05-11-2010, 04:41 PM
|
#93 |
|
Registered User
Join Date: Aug 2009
Location: Lambertville MI
Posts: 962
|
Re: Custom 1987 GMC Crew Cab Short Bed
if i had the cash, this is exactally the truck id build.. only i dont know if id use a new dirtymax or cummins.. but i have always wanted a crew long or short lifted with a new diesel in it. this thing is sick bro.. keep up the awesome work!
__________________
"I'll keep my guns, money, and freedom. You can keep the "change" |
|
|
|
05-11-2010, 10:13 PM
|
#94 |
|
6>8 Plugless........
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 17,142
|
Re: Custom 1987 GMC Crew Cab Short Bed
5.9 or 6.7? Very cool!
__________________
Ryan 1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread 1972 GMC Sierra Grande Longhorn 4x4 1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed 1972 C10 Suburban Custom Deluxe 1969 Chevy milk truck 1971 Camaro RS 5.3 BTR STG3 Cam Super T10 1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project Tired of spark plugs? Check this out. |
|
|
|
05-11-2010, 11:03 PM
|
#95 | |
|
Badass
Join Date: Jan 2009
Location: lox. fl
Posts: 4,586
|
Re: Custom 1987 GMC Crew Cab Short Bed
Quote:
__________________
Think outside the box? -84c10 (1stcar)→My Build←  -00 Saturn 5spd drop a gear and disappear! 1/4:13:90
|
|
|
|
|
05-12-2010, 02:45 PM
|
#96 |
|
Registered User
Join Date: May 2010
Location: Rochester NY
Posts: 831
|
Re: Custom 1987 GMC Crew Cab Short Bed
NICE-subcribed
|
|
|
|
05-12-2010, 10:15 PM
|
#97 |
|
Account Suspended
Join Date: Oct 2009
Location: Warrington, PA
Posts: 27
|
Re: Custom 1987 GMC Crew Cab Short Bed
Hey sorry im a little late for this conversation, but totally a graduate of Wyotech next month in June 2010, out at the Blairsville PA Campus. And totally the same stuff here with big headed people and it being an introduction, truck is looking badass by the way haha
-Adam |
|
|
|
05-12-2010, 11:43 PM
|
#98 |
|
Account Suspended
Join Date: Jun 2009
Posts: 269
|
Custom 1987 GMC Crew Cab Short Bed
The long awaited photos:
2007 Dodge 3500 4X4 with a 5.9L Cummins diesel... Only 42,000 miles! |
|
|
|
05-12-2010, 11:47 PM
|
#99 |
|
Account Suspended
Join Date: Jun 2009
Posts: 269
|
Custom 1987 GMC Crew Cab Short Bed
This truck is a roll over... Chassis, axles, motor, radiator, intercooler, etc... Perfect and untouched...
Body...Trashed! 6 Speed manual trans (G56 Mercedes Industrial medium duty) |
|
|
|
05-12-2010, 11:49 PM
|
#100 |
|
6>8 Plugless........
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 17,142
|
Re: Custom 1987 GMC Crew Cab Short Bed
Ditch that G56!
 They are a problem child and hard to get parts for. Very nice score though!
__________________
Ryan 1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread 1972 GMC Sierra Grande Longhorn 4x4 1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed 1972 C10 Suburban Custom Deluxe 1969 Chevy milk truck 1971 Camaro RS 5.3 BTR STG3 Cam Super T10 1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project Tired of spark plugs? Check this out. Last edited by Dieselwrencher; 05-12-2010 at 11:50 PM. |
|
|
 |
| Bookmarks |
|
|
Linear Mode
