Project 91 Bsquared - Page 4 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

*BGRAFX* · 07-21-2010, 03:34 PM

This wire was taped off and I was missing vacuum hoses from the egr and the cruise was going to the ac vent and another hose was supposed to be coming from the back of the manifold but instead was T connected to the wipers.

**Dieselwrencher** · 07-21-2010, 03:51 PM

That's always nice. Some people.

RandyP · 07-21-2010, 03:52 PM

It started didn't it?

You want it fixed? Or you want it fixed right? To some people, there is no difference.

*BGRAFX* · 07-21-2010, 09:49 PM

I can't figure it out, I got it running and took it for a short test drive. Then got stranded. But after 30min of sitting on the side of the road it started up, so headed back home and tinkered with it for a little bit before taking it out for another quick test drive which resulted in 2 more shut downs. I'm not sure where to go from here.

**Dieselwrencher** · 07-22-2010, 12:07 AM

There isn't another fusable link somewhere else farther up the wire is there?

bluex · 07-23-2010, 05:25 PM

Sounds like something like this might be your best bet. I know thats what I'm going to have to do on my K5 based on the hacking I've seen in it so far....

http://www.summitracing.com/search/P...s&autoview=SKU

justpball · 07-26-2010, 04:35 PM

any luck bro?

*BGRAFX* · 07-26-2010, 04:54 PM

No luck yet

justpball · 07-26-2010, 05:00 PM

man that sucks bro...

Chlsnk · 07-26-2010, 06:10 PM

Have you pulled your Dizzy's cap and checked for cracks ? Sounds almost liek there could be moisture in there.

justpball · 07-26-2010, 07:37 PM

My truck did that one time and it was the wires down by the starter that were in that metal tube heat shield thingy, but I think you said you already redid those wires

**scotts62** · 07-27-2010, 12:32 AM

So when driving it just dies on you, right?
You check the wires at the starter? Have you replaced the ignition module? I have had one do that, when you drove it for a while it would die but you let it sit for a bit and off you would go, fuel pump going out would do it too..

*BGRAFX* · 07-27-2010, 08:32 AM

Not much of an update:
I changed oil, fuel filter, spark plugs & wires, map sensor (code 33), spark control sensor (code 43), new starter and wiring, battery checked out good 12.4V, ignition control module (black piece under distributor cap) checked good although I've been told that when the engine warms up the ignition module or the coil (the shortest spark wire connect to in front of the distributor cap) with shut off and cause the engine to die while driving. Which is exactly what its doing, I can only get a few blocks away and the truck will die, then I have to wait about 10min before it will start back up and drive a few more blocks then die again. Another thing is that my truck has very little get up and go, I can only go about 50mph tops. Which could mean a clogged catalytic converter.
I hope to be very productive this weekend changing parts and getting it running strong.

spudz · 07-28-2010, 12:04 PM

My bet is on ignition module under the cap.............. In my experience coils are either good or bad most of the time.

**scotts62** · 07-28-2010, 04:36 PM

Well is it up roasting tires yet??

justpball · 07-28-2010, 04:43 PM

had a fuel pump do that to me and a coil.

*BGRAFX* · 07-28-2010, 04:58 PM

Still not fixed yet but I did just pass this awesome lady driver bahahahahahaha

JohnC · 07-29-2010, 01:16 PM

she better hope the airbag doesn't go off. I bet it'll take her head off!

*BGRAFX* · 08-06-2010, 11:23 PM

Pic of the burb

joe231 · 08-06-2010, 11:32 PM

Nice pic!!

*BGRAFX* · 08-08-2010, 11:30 AM

Man! my big back passenger side window is cracked! Hope I can find one at the junk yard.
My theory is the landscapers mower flung a rock and hit my window

joe231 · 08-08-2010, 08:06 PM

Dang-IT!!

cochino12 · 08-08-2010, 08:19 PM

Quote:

Originally Posted by BGRAFX

Man! my big back passenger side window is cracked! Hope I can find one at the junk yard.
My theory is the landscapers mower flung a rock and hit my window

oh yeah blame it on the landscapers ha ha, there are several here at the yard I go to if you need me to pull one out for you.

*BGRAFX* · 08-08-2010, 08:46 PM

Adam, you damn lawn boys! lol a first I blamed neighborhood kids throwing rocks, or a drive by bb gun incident. But then I thought about seeing the landscaper driving his mower through the parking lot and since I haven't been driving my truck it was a sitting duck for debris. I've talked to a couple local guys parting out suburbans but I will let you know how it goes.
The thing I most bummed about is that in the corner of all the windows on my burb the glass is etched with the vin#

blakeduren · 08-08-2010, 10:45 PM

I think I have the true weatherstripping tool to install that locking strip on the window. Let me know if you want to try it out.

Edit:

I went the 12th street yard and there is an spray painted black 88 Sub with tinted rear windows still in it.

07-21-2010, 03:34 PM	#76
BGRAFX Account Suspended Join Date: Jun 2009 Location: kansas city Ks Posts: 1,970	Re: Project 91 Bsquared This wire was taped off and I was missing vacuum hoses from the egr and the cruise was going to the ac vent and another hose was supposed to be coming from the back of the manifold but instead was T connected to the wipers. Attached Images

07-21-2010, 03:51 PM	#77
Dieselwrencher 6>8 Plugless........ Join Date: Sep 2007 Location: Prairie City, Ia Posts: 17,142	Re: Project 91 Bsquared That's always nice. Some people. __________________ Ryan 1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread 1972 GMC Sierra Grande Longhorn 4x4 1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed 1972 C10 Suburban Custom Deluxe 1969 Chevy milk truck 1971 Camaro RS 5.3 BTR STG3 Cam Super T10 1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project *Tired of spark plugs? Check this out.*

07-21-2010, 03:52 PM	#78
RandyP Getting Old; Going Broke Join Date: Apr 2010 Location: Owasso OK Posts: 2,764	Re: Project 91 Bsquared It started didn't it? You want it fixed? Or you want it fixed right? To some people, there is no difference. __________________ *Why is every used 350 sbc out of a corvette?* There's only two things that excite a man, expensive toys and real expensive toys. *VEGETARIAN: That's an old Indian word meaning "I don't hunt so good."* When the going gets tough, switch to power tools.

07-21-2010, 09:49 PM	#79
BGRAFX Account Suspended Join Date: Jun 2009 Location: kansas city Ks Posts: 1,970	Re: Project 91 Bsquared I can't figure it out, I got it running and took it for a short test drive. Then got stranded. But after 30min of sitting on the side of the road it started up, so headed back home and tinkered with it for a little bit before taking it out for another quick test drive which resulted in 2 more shut downs. I'm not sure where to go from here.

07-22-2010, 12:07 AM	#80
Dieselwrencher 6>8 Plugless........ Join Date: Sep 2007 Location: Prairie City, Ia Posts: 17,142	Re: Project 91 Bsquared There isn't another fusable link somewhere else farther up the wire is there? __________________ Ryan 1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread 1972 GMC Sierra Grande Longhorn 4x4 1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed 1972 C10 Suburban Custom Deluxe 1969 Chevy milk truck 1971 Camaro RS 5.3 BTR STG3 Cam Super T10 1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project *Tired of spark plugs? Check this out.*

07-23-2010, 05:25 PM	#81
bluex Registered User Join Date: Jun 2004 Location: Spartanburg, SC Posts: 1,963	Re: Project 91 Bsquared Sounds like something like this might be your best bet. I know thats what I'm going to have to do on my K5 based on the hacking I've seen in it so far.... http://www.summitracing.com/search/P...s&autoview=SKU __________________ Paul '78 GMC Serria 15 Heavy Half. 361/NV3500/3.73. Former LWB NV3500 swap Trailing arm swap '98 ECSB Z71 daily driver -traded '03 burb. Family cruiser http://upstategmtrucks.com/

07-26-2010, 04:35 PM	#82
justpball Registered User Join Date: Dec 2008 Location: Silverhill, Al Posts: 2,026	Re: Project 91 Bsquared any luck bro? __________________ Fuzzy Dice Club Member 87 Crew SWB Build for the crew http://67-72chevytrucks.com/vboard/s...d.php?t=430082 http://www.cardomain.com/ride/3232925 90 burb 2wd Build Thread For The Burb! http://67-72chevytrucks.com/vboard/s...d.php?t=383055

07-26-2010, 04:54 PM	#83
BGRAFX Account Suspended Join Date: Jun 2009 Location: kansas city Ks Posts: 1,970	Re: Project 91 Bsquared No luck yet

07-26-2010, 05:00 PM	#84
justpball Registered User Join Date: Dec 2008 Location: Silverhill, Al Posts: 2,026	Re: Project 91 Bsquared man that sucks bro... __________________ Fuzzy Dice Club Member 87 Crew SWB Build for the crew http://67-72chevytrucks.com/vboard/s...d.php?t=430082 http://www.cardomain.com/ride/3232925 90 burb 2wd Build Thread For The Burb! http://67-72chevytrucks.com/vboard/s...d.php?t=383055

07-26-2010, 06:10 PM	#85
Chlsnk Registered User Join Date: Jan 2009 Location: Kansas city Posts: 756	Re: Project 91 Bsquared Have you pulled your Dizzy's cap and checked for cracks ? Sounds almost liek there could be moisture in there. __________________ *My 84 short bed build up*** http://67-72chevytrucks.com/vboard/s...68#post3481968

07-26-2010, 07:37 PM	#86
justpball Registered User Join Date: Dec 2008 Location: Silverhill, Al Posts: 2,026	Re: Project 91 Bsquared My truck did that one time and it was the wires down by the starter that were in that metal tube heat shield thingy, but I think you said you already redid those wires __________________ Fuzzy Dice Club Member 87 Crew SWB Build for the crew http://67-72chevytrucks.com/vboard/s...d.php?t=430082 http://www.cardomain.com/ride/3232925 90 burb 2wd Build Thread For The Burb! http://67-72chevytrucks.com/vboard/s...d.php?t=383055

07-27-2010, 12:32 AM	#87
scotts62 One day... Join Date: Apr 2008 Location: Tuttle, Ok Posts: 9,243	Re: Project 91 Bsquared So when driving it just dies on you, right? You check the wires at the starter? Have you replaced the ignition module? I have had one do that, when you drove it for a while it would die but you let it sit for a bit and off you would go, fuel pump going out would do it too.. __________________ Scott 93 crew cab build Project 62

07-27-2010, 08:32 AM	#88
BGRAFX Account Suspended Join Date: Jun 2009 Location: kansas city Ks Posts: 1,970	Re: Project 91 Bsquared Not much of an update: I changed oil, fuel filter, spark plugs & wires, map sensor (code 33), spark control sensor (code 43), new starter and wiring, battery checked out good 12.4V, ignition control module (black piece under distributor cap) checked good although I've been told that when the engine warms up the ignition module or the coil (the shortest spark wire connect to in front of the distributor cap) with shut off and cause the engine to die while driving. Which is exactly what its doing, I can only get a few blocks away and the truck will die, then I have to wait about 10min before it will start back up and drive a few more blocks then die again. Another thing is that my truck has very little get up and go, I can only go about 50mph tops. Which could mean a clogged catalytic converter. I hope to be very productive this weekend changing parts and getting it running strong.

07-28-2010, 12:04 PM	#89
spudz Registered User Join Date: Oct 2005 Location: Branchville SC Posts: 1,647	Re: Project 91 Bsquared My bet is on ignition module under the cap.............. In my experience coils are either good or bad most of the time. __________________ 2004 z71, 96 z71 on 38s, 88 Chevy k5 blazer, 4in lift. 84 swb project, 82 SWB project , 84 chevy 4x4 lwb project, 88 Jimmy beater/highschool ride. 79 c30. 99 tahoe 4x4 project. and a bunch of parts trucks..

07-28-2010, 04:36 PM	#90
scotts62 One day... Join Date: Apr 2008 Location: Tuttle, Ok Posts: 9,243	Re: Project 91 Bsquared Well is it up roasting tires yet?? __________________ Scott 93 crew cab build Project 62



Register or Log In To remove these advertisements.

07-28-2010, 04:43 PM	#91
justpball Registered User Join Date: Dec 2008 Location: Silverhill, Al Posts: 2,026	Re: Project 91 Bsquared had a fuel pump do that to me and a coil. __________________ Fuzzy Dice Club Member 87 Crew SWB Build for the crew http://67-72chevytrucks.com/vboard/s...d.php?t=430082 http://www.cardomain.com/ride/3232925 90 burb 2wd Build Thread For The Burb! http://67-72chevytrucks.com/vboard/s...d.php?t=383055

07-28-2010, 04:58 PM	#92
BGRAFX Account Suspended Join Date: Jun 2009 Location: kansas city Ks Posts: 1,970	Re: Project 91 Bsquared Still not fixed yet but I did just pass this awesome lady driver bahahahahahaha Attached Images Last edited by BGRAFX; 07-28-2010 at 05:53 PM.

07-29-2010, 01:16 PM	#93
JohnC Registered User Join Date: Feb 2009 Location: Oklahoma Posts: 7,461	Re: Project 91 Bsquared she better hope the airbag doesn't go off. I bet it'll take her head off!

08-06-2010, 11:23 PM	#94
BGRAFX Account Suspended Join Date: Jun 2009 Location: kansas city Ks Posts: 1,970	Re: Project 91 Bsquared Pic of the burb Attached Images

08-06-2010, 11:32 PM	#95
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: Project 91 Bsquared Nice pic!! __________________ *CHEVY ONLY*

08-08-2010, 11:30 AM	#96
BGRAFX Account Suspended Join Date: Jun 2009 Location: kansas city Ks Posts: 1,970	Re: Project 91 Bsquared Man! my big back passenger side window is cracked! Hope I can find one at the junk yard. My theory is the landscapers mower flung a rock and hit my window Attached Images Last edited by BGRAFX; 11-14-2010 at 05:31 PM.

08-08-2010, 08:06 PM	#97
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: Project 91 Bsquared Dang-IT!! __________________ *CHEVY ONLY*

08-08-2010, 08:46 PM	#99
BGRAFX Account Suspended Join Date: Jun 2009 Location: kansas city Ks Posts: 1,970	Re: Project 91 Bsquared Adam, you damn lawn boys! lol a first I blamed neighborhood kids throwing rocks, or a drive by bb gun incident. But then I thought about seeing the landscaper driving his mower through the parking lot and since I haven't been driving my truck it was a sitting duck for debris. I've talked to a couple local guys parting out suburbans but I will let you know how it goes. The thing I most bummed about is that in the corner of all the windows on my burb the glass is etched with the vin#

08-08-2010, 10:45 PM	#100
blakeduren Registered User Join Date: Apr 2010 Location: Kansas City, MO Posts: 192	Re: Project 91 Bsquared I think I have the true weatherstripping tool to install that locking strip on the window. Let me know if you want to try it out. Edit: I went the 12th street yard and there is an spray painted black 88 Sub with tinted rear windows still in it. Last edited by blakeduren; 08-09-2010 at 04:02 PM.

Register or Log In To remove these advertisements.