slik ricks 67 short wide CST - Page 4 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

2manyprojects · 09-03-2010, 09:27 PM

Quote:

Originally Posted by 67chevy1series

no it doesnt it has unessasary holes on the side must have been the po

Those holes are the rare 67 only taillight cooling duct option more desirable than buddy buckets.

I found a parts truck with the same option, going to check it out tomorrow, that way it will save you some shipping cost.

67chevy1series · 09-04-2010, 01:12 AM

Quote:

Originally Posted by 2manyprojects

Those holes are the rare 67 only taillight cooling duct option more desirable than buddy buckets.

I found a parts truck with the same option, going to check it out tomorrow, that way it will save you some shipping cost.

67chevy1series · 09-05-2010, 03:26 PM

well got some parts from the pick n pull and gion back again what tools do you need to take 67 68 side trim off my dad is gonna go soon so any fast replys would be great hey old blue do you remember wahat you used

72chevyfleet · 09-11-2010, 12:57 PM

i do say you have a nice thread here and a nice truck your not gonna run headers?

67chevy1series · 09-11-2010, 02:56 PM

nope my dad has too many problems with them plus it give it that good look all the pics the fender isnt on so i will tryto get an engine comp. pic for you thanks, rick

Newtz67 · 09-12-2010, 01:34 PM

I finally found your thread, right on! Any new progress? Good seeing you out at sonic!

67chevy1series · 09-12-2010, 02:14 PM

Quote:

Originally Posted by Newtz67

I finally found your thread, right on! Any new progress? Good seeing you out at sonic!

thanks your truck aint that bad either i wish i could hear it run every time i see it ,its parked

67chevy1series · 09-12-2010, 02:23 PM

well gut i kinda held out on ya little bit i wasnt on awhile ago cause we switched our internet so it was off for a day or two and im too youyng to go into pick n pull you have to be 16

there is a cst 67 (i didnt believe him when he told me until he showed me a pic) but it has a 68 bed, so i told my dad what i needed and he went down there and about 2 1/2 hours and about 40 bucks i got this:
two parking light housings w/ pig tails (the wiring)
the brace that goes on the inner driverside fender
67 mirror and arm (bracket)since they are hard to find
trim for the frnt
door trim
drivers side cab trim
passenger side wheel welll bed trim
the glove box door
the h for chevrolet on the hood
a bunch of the plugs that go on the doors door jamb
and thats it

Hubscrub · 09-12-2010, 02:25 PM

^^yall didn't buy me anything?

nice work

67chevy1series · 09-12-2010, 02:31 PM

Quote:

Originally Posted by Hubscrub

^^yall didn't buy me anything?

nice work

67chevy1series · 09-15-2010, 12:15 AM

well im am going to be trading my bed sides (68) for a 67 will be getting tommorow my 67 dog dish chrome and red and hopefully my window rubbers come in tommorrow

67chevy1series · 09-16-2010, 12:33 AM

well i no i have been laging on the pics but i will get some i got my window rubbers in the mail today got the back window in and now we need the front but that is going to be a pain so we are going to have some one come out and do it but i also got those hubcaps they are pretty good i would say

VA72C10 · 09-16-2010, 01:09 AM

67chevy1series · 09-16-2010, 02:21 AM

well see if i cant get you some pics then va72c10 well this is the bed i will be trading for my 68 bedsides

and

and another

67chevy1series · 09-16-2010, 02:25 AM

here is the engine a little better and my door trim repainted black

and

VA72C10 · 09-16-2010, 07:22 AM

looks like a pretty nice bed and that door trim looks great!

67chevy1series · 09-16-2010, 09:59 AM

thanks my dad got the trim and i cleaned it

classic1967chevy · 09-16-2010, 11:02 AM

well looks like you are makeing some great progress just keep up the good work i know they take a lot of time and hard work but they are worth it in the long run

67chevy1series · 09-16-2010, 05:54 PM

ya i know well hopefully i can get the front window in inbody have any advce
we cant even get the rubber on the window inorder to put it on the cab

VA72C10 · 09-16-2010, 07:22 PM

What brand seal? Are you using silicone or window spray to make the gasket easier to slide on the windshield? Then put rope in the back, install from the front, and pull the rope out as you pull in and it'll seat itself....sounds easy, huh

67chevy1series · 09-16-2010, 08:02 PM

Quote:

Originally Posted by VA72C10

What brand seal? Are you using silicone or window spray to make the gasket easier to slide on the windshield? Then put rope in the back, install from the front, and pull the rope out as you pull in and it'll seat itself....sounds easy, huh

no silicone just rubber seals but i dont think we can put a rope in between

sleepertruck72 · 09-17-2010, 02:03 AM

I used a fat speaker wire when I helped a friend do it, we also used a heat gun to help soften it up and a suction cup to help move it around. Here's a youtube link that makes it look so easy

YouTube - 1967 Chevy Pickup Windshield...

67chevy1series · 09-17-2010, 07:04 PM

thanks man

sleepertruck72 · 09-17-2010, 11:04 PM

So did you get the windshield in ?

If not, hurry its supposed to rain on Sunday.

67chevy1series · 09-17-2010, 11:46 PM

Quote:

Originally Posted by sleepertruck72

So did you get the windshield in ?

If not, hurry its supposed to rain on Sunday.

well does half qualify

dont worry i will get it in even if i half to persuade it

09-05-2010, 03:26 PM	#78
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: slik ricks 67 short wide custom/10 well got some parts from the pick n pull and gion back again what tools do you need to take 67 68 side trim off my dad is gonna go soon so any fast replys would be great hey old blue do you remember wahat you used

09-11-2010, 12:57 PM	#79
72chevyfleet Learning As I Go Join Date: Feb 2009 Location: scotts valley california Posts: 250	Re: slik ricks 67 short wide custom/10 i do say you have a nice thread here and a nice truck your not gonna run headers? __________________ 1972 Chevy C-20 Longbed 2wd Granny Low with a Crate 350: Air Gap Manifold, Edelbrock 600cfm, HEI, Headers to a 40 series flow (soon to be dual again)

09-11-2010, 02:56 PM	#80
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: slik ricks 67 short wide custom/10 nope my dad has too many problems with them plus it give it that good look all the pics the fender isnt on so i will tryto get an engine comp. pic for you thanks, rick

09-12-2010, 01:34 PM	#81
Newtz67 Registered User Join Date: Mar 2010 Location: A t w a t e r, Ca Posts: 1,201	Re: slik ricks 67 short wide custom/10 I finally found your thread, right on! Any new progress? Good seeing you out at sonic! __________________ My '67 short wide Our '68 Burb My '04 Z71 The '54 Belair The '69 Cadillac

09-12-2010, 02:23 PM	#83
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: slik ricks 67 short wide custom/10 well gut i kinda held out on ya little bit i wasnt on awhile ago cause we switched our internet so it was off for a day or two and im too youyng to go into pick n pull you have to be 16there is a cst 67 (i didnt believe him when he told me until he showed me a pic) but it has a 68 bed, so i told my dad what i needed and he went down there and about 2 1/2 hours and about 40 bucks i got this: two parking light housings w/ pig tails (the wiring) the brace that goes on the inner driverside fender 67 mirror and arm (bracket)since they are hard to find trim for the frnt door trim drivers side cab trim passenger side wheel welll bed trim the glove box door the h for chevrolet on the hood a bunch of the plugs that go on the doors door jamb and thats it

09-12-2010, 02:25 PM	#84
Hubscrub Cruzin Join Date: Dec 2009 Location: on the road Posts: 2,835	Re: slik ricks 67 short wide custom/10 ^^yall didn't buy me anything? nice work __________________ Lime Wife's 67https://www.google.com/url?sa=t&rct=...wZEMODaS2d94u8 Back to the Fifties 59 https://www.google.com/url?sa=t&rct=...NAeStpydfrcj_U Proverbs 3:5,6 "Thanks to the Interstate Highway System, it is now possible to travel across the country from coast to coast without seeing anything."Charles Kuralt In memory of our first baby daughter, daddy and mommy love you. Danica Grace 6/26/14

09-15-2010, 12:15 AM	#86
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: slik ricks 67 short wide custom/10 well im am going to be trading my bed sides (68) for a 67 will be getting tommorow my 67 dog dish chrome and red and hopefully my window rubbers come in tommorrow

09-16-2010, 12:33 AM	#87
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: slik ricks 67 short wide custom/10 well i no i have been laging on the pics but i will get some i got my window rubbers in the mail today got the back window in and now we need the front but that is going to be a pain so we are going to have some one come out and do it but i also got those hubcaps they are pretty good i would say

09-16-2010, 01:09 AM	#88
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,267	Re: slik ricks 67 short wide custom/10 __________________ Looking for a 67-72 swb or blazer project in or around VA.

09-16-2010, 02:21 AM	#89
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: slik ricks 67 short wide custom/10 well see if i cant get you some pics then va72c10 well this is the bed i will be trading for my 68 bedsides andand another Last edited by 67chevy1series; 09-16-2010 at 02:28 AM.

09-16-2010, 02:25 AM	#90
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: slik ricks 67 short wide custom/10 here is the engine a little better and my door trim repainted black and Last edited by 67chevy1series; 09-16-2010 at 02:26 AM.

09-16-2010, 07:22 AM	#91
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,267	Re: slik ricks 67 short wide custom/10 looks like a pretty nice bed and that door trim looks great! __________________ Looking for a 67-72 swb or blazer project in or around VA.

09-16-2010, 09:59 AM	#92
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: slik ricks 67 short wide custom/10 thanks my dad got the trim and i cleaned it

09-16-2010, 11:02 AM	#93
classic1967chevy Registered User Join Date: Apr 2010 Location: Nauvoo Alabama Posts: 269	Re: slik ricks 67 short wide custom/10 well looks like you are makeing some great progress just keep up the good work i know they take a lot of time and hard work but they are worth it in the long run

09-16-2010, 05:54 PM	#94
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: slik ricks 67 short wide custom/10 ya i know well hopefully i can get the front window in inbody have any advce we cant even get the rubber on the window inorder to put it on the cab



Register or Log In To remove these advertisements.

09-16-2010, 07:22 PM	#95
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,267	Re: slik ricks 67 short wide custom/10 What brand seal? Are you using silicone or window spray to make the gasket easier to slide on the windshield? Then put rope in the back, install from the front, and pull the rope out as you pull in and it'll seat itself....sounds easy, huh __________________ Looking for a 67-72 swb or blazer project in or around VA.

09-17-2010, 07:04 PM	#98
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: slik ricks 67 short wide custom/10 thanks man

09-17-2010, 11:04 PM	#99
sleepertruck72 Registered User Join Date: Nov 2007 Location: Turlock California 95380 Posts: 2,075	Re: slik ricks 67 short wide custom/10 So did you get the windshield in ? If not, hurry its supposed to rain on Sunday. __________________ 72 C20 Longbed 05 1500 Z71 Last edited by sleepertruck72; 09-17-2010 at 11:05 PM.

Register or Log In To remove these advertisements.