KY 67 SWB Part Out!

[slick copper]

They're most likely not double hump heads. I remember the valves being wayyyy tooo small to be double humps. Could've been swapped out some time I guess though.

[Delta9]

do you still have the complete front clip, as in fenders, hood, grill and core. also are they chevy and in good shape? how much would this run me if picked up?

[slick copper]

The front clip is long gone man, sorry. It was the first thing to go before I even started this thread.

[spyder4560]

Just wanted to wave a hand from Danville,Ky.Also would like to know if you plan on selling the frame complete or maybe part with the trailing arm setup.Whichever,could you price them both ways?I am only about an hour and a half away,so pickup should not be a problem if the price is right.

[slick copper]

Hey! Wanted to keep the frame complete, but asking $600 and right now I'm offering what's left of the cab and bed in with it. I feel that's pretty fair deal for a short wheel base. Was it you that was asking about doors in a KY thread before? I got those too, maybe we can work out a deal on all of it.

[spyder4560]

Thanks for the quick response.Would really like to talk about making this frame deal work out.My nephew has a '71 LWB that I would like to make into a SWB and if this frame(and any other parts)is in good shape we will definitely need to talk.Send me a PM with your phone number and let's see if we can get together on this deal.

[spyder4560]

Slick copper,you need to clean out your PM storage.I couldn't leave you a PM.

[slick copper]

DONE!! Sorry had sooo many from my high octane membership when it expired cut my available space down and made my box full! I've got it cleaned up and renewed my subscription/membership now so good to go!!

[YunGunz]

Any luck/chance some of the bed supports are not rusted out?

[slick copper]

Originally Posted by YunGunz

Any luck/chance some of the bed supports are not rusted out?

Actually it's a good possibility. The inner fenders are solid, they're just a little beat up. Here's a couple undershots, not exact of bedrails but maybe give ya an idea of condition. Looks like some surface rust, maybe solid though. I'll have to take a closer look for ya when I go out there.

[slick copper]

For Heavy Metal Chevy. Here's where I'm looking for numbers man. Probably not the right spot. Let me know.

[yellowGT]

ill give you $10 shipped for the wiper motor arms? let me know. Thx

[slick copper]

How 'bout $15 (just cause shipping to TX $$)?

[yellowGT]

just struck deal with teeitup on some...thanks though

[angelo_32806]

Do you have a title
Lee

[michael bustamante]

Did those cab corners ever sell?

[Portmod7]

How about the bellhousing inspection cover? That's assuming it had a manual transmission with the stock bellhousing in it?

[slick copper]

Originally Posted by angelo_32806

Do you have a title
Lee

No, sorry. Gone.

Originally Posted by michael bustamante

Did those cab corners ever sell?

Nope, still got them both. No one ever followed through. Have rocker patch and both floor boards available too.

Originally Posted by Portmod7

How about the bellhousing inspection cover? That's assuming it had a manual transmission with the stock bellhousing in it?

You need one? I'd have to look. My '70 did have a manual tranny, not sure if the cover is still around.

[C5Phil]

I know this is a long shot but I'm going to try... By chance would you still have/consider selling- a cut out patch from your cab -I need the piece that incorporates the gas filler neck behind the drivers door- if you could cut me a patch panel that runs from the trim line two inches above filler to about 10-12 inches below the filler (I don't need the door jamb- just to the edge of the jamb and to the back of the cab)) I'd be very appreciative-- I hope I'm describing it correctly but my cab - under Po- took a hit right under gas filler neck- PO bondo-ed the area and I'd like to repair it properly-- let me know- I know its a long shot-- Thanks- Phil H.

[slick copper]

Originally Posted by C5Phil

I know this is a long shot but I'm going to try... By chance would you still have/consider selling- a cut out patch from your cab -I need the piece that incorporates the gas filler neck behind the drivers door- if you could cut me a patch panel that runs from the trim line two inches above filler to about 10-12 inches below the filler (I don't need the door jamb- just to the edge of the jamb and to the back of the cab)) I'd be very appreciative-- I hope I'm describing it correctly but my cab - under Po- took a hit right under gas filler neck- PO bondo-ed the area and I'd like to repair it properly-- let me know- I know its a long shot-- Thanks- Phil H.

Hmm... I'll think about it. Actually, yeah I probably would really need the $ right now. How much would a man be willing to pay for that peice? I will need a little more description. A pic with the section outlined would be great. I know the area you're talking about. Might be able to work this out.

[slick copper]

TTT!!!! PRICE CUTS GUYS!!! Check them out!! Please buy this leftover stuff so I can continue project Slick Copper! Heavy Metal Chevy I dropped the price on wheels/tires. And Spyder the frame price has dropped! Help me out guys!!

[C5Phil]

This picture shows the patch area I need- do not need the door jamb side- Let me know what you want for it shipped to 14589 zip- looking for a good no rust/bondo piece- thanks in advance-Phil

[slick copper]

Ok. My truck looks good and straight no bondo. Does have some light suface rust, nothing that wouldn't sand out. So from the body line down to about 14" below fuel opening (just to be safe) right? How far around the corner of the cab? Until it flattens out? Just wanna be sure before I go cuttin'. Gonna have to remove that old gas tank. I'm thinking including shipping $60. Seeing I'm gonna have to cut the cab, and everything. How's that sound?

[C5Phil]

Sounds good- But better hold off cutting for a bit- another fellow- "oldchevyguy" has offered to cut up one of his cabs and I need to verify he got my message that I'm getting one from you- so wait till I hear from him please- sorry- don't want him cutting up a good cab for know reason- thanks - Phil

[C5Phil]

Re: the cab patch- Looks like I'm all set with OldChevyGuy - but if you don't mind I'll keep you in mind in case the patch he sends doesn't fit my needs- thanks for you patience in this matter- Phil