my patinia'd 69

[JustCallMeDrew]

where do i take a look because im interested?

[69chevy lwb]

Here's the center console I built

[JustCallMeDrew]

Wow very nice...thanks for the help if i have any more questions i know where to come!

[67chevy1series]

Originally Posted by 69chevy lwb

Thank you, I'm not sure why gm didn't just build it that way to start with it has way better flow. But I'm actually going to build a new one so the heater core is in the cab with a push fan inside so it recycles the hot air and allows me to get rid of the big fiberglass heater box

It seems if you get a factory ac cab heater box and built a block off and added holes for the ducts to attach you could have your heater core inside and maintain the same principle... Only thing is the fan. Kind of a tuffy maybe if you reworked the passenger fresh air vent and basically reversed it that might work... I don't know just shooting ideas I'm sure you have a much better idea then this. Can't wait to see what you come up with

[JustCallMeDrew]

Hey bud i came up with a parts list but i dont know if its a whole kit and would work please help!
-4 Dominator 2600 bags
-8 SMC or AVS 1/2" valves
-Homemade switch
-1 Viair #444c Compressor
-Old 5 galon air tank my grandpa has

Then all i would need is bag mounting brackets and air lines correct?

[69chevy lwb]

I recommend you get big red or little Larry's manual valves. I think that's the name but then there's nothing to go wrong and you will only need three ports on the tank rather than seven. Then spend the money you saved on dual 480c or equivalent. That's the heart of the setup so don't skimp

[JustCallMeDrew]

Can i "play" with the bags while driving with manual valves

[69chevy lwb]

Yes you push the paddle up and the truck goes up push it down and it goes down it has a supply to the valves so the whole thing is ran off of them

[JustCallMeDrew]

You know what im just going to say **** it and save my money and go all out and build mine like yours...can you pm me a total cost of everything you have in the truck please and thanks!

[JustCallMeDrew]

Ok two more questions...sorry for all the questions...can i get pictures of your panhard bar and bag plates in rear and c-notch? and how hard was the c-notch and how did you do it?

[JustCallMeDrew]

Ok i decided i want to run porterbuilt stage 1 front and for the rear i really want to run stage 2 porterbuilt but if i could get just as low with stage 1 and a home made notch i will probably do that...and a viair 480c with 5 gallon tank and smc 1/2" valves!

[69chevy lwb]

Sorry I never got back to you. I do recommend manual valves but that's my preference. It might be worth calling mate at porterbuilt or ride tech or avs the choice is yours but they can tell you everything you need to know and there all good people to do business with. I don't really have any good pictures of the set up but go to the c10 forum and read the air baggin forum it should answer your question s

[JustCallMeDrew]

Ok thanks bud...yeah when im ready to order i will hit up nate at pb and see what all i will need and try to make a deal with him!

[69chevy lwb]

The motor is about ready to be fired up just a few more thing's to do and then hopefully all goes well.

[tommyd241]

Cool truck!

[Rusbuilt]

Engine is looking good!!

[mcbassin]

Very clean

[cobra_4]

Very cool ride! I dig it!

[69chevy lwb]

I'm still chugging along but got a ways to go the motor isn't too far out but I got a little paint work done. Thanks a ton for all the compliments by the way

[hutcholdschool]

WOW your truck looks great. I have been following your build for quite awhile on this site and the other and always look forward to your updates.

[VA72C10]

Great work! Love everything you've done!

[69chevy lwb]

Thanks guys! I'm really hoping to finish this one soon so I can get after the 68 I picked up last summer

[mcbassin]

Very nice progress

[Rusbuilt]

nice bro!