CA Cabs Need any cuts, parts etc?! - Page 4 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Undone · 10-20-2013, 07:32 PM

How much for trans tunnel as outlined straight back to where fuel line goes thru floor? Shipping to 30530.

7dee2 · 10-23-2013, 11:41 AM

Quote:

Originally Posted by budnikguy

aftamathe86 - your lo hump patch is cut, boxed, and will get it to the PO tomorrow or Monday.

kaphillips- your divider trim, clips, and gas cap are boxed and will get it to the PO tomorrow or Monday.

*Gregg*- Payment received. I will get the firewall pieces cut for you this weekend and have them packaged and shipped asap.

7dee2- your "RV" fill in pieces have been cut, scouring for a box big and sturdy enough to take down to Greyhound for the shipping cost quote.

sduckworth13- Payment received. I will get the floor patch cut for you this weekend and have them packaged and shipped asap.

Adam, Any news on my Greyhound quote?

Thanks,

Sanchez Garage · 10-23-2013, 11:03 PM

any frames? fenders ?Were in Riverside-- I am off Vanburren/canyon ridge

budnikguy · 10-23-2013, 11:14 PM

We are practically neighbors...i am on Roberts near Dauchy. I can help you with all of that.

Adam

budnikguy · 10-23-2013, 11:16 PM

working on making a box...the back side of the cab is an odd size to try and find......

Quote:

Originally Posted by 7dee2

Adam, Any news on my Greyhound quote?

Thanks,

budnikguy · 10-23-2013, 11:16 PM

$50 delivered....

Quote:

Originally Posted by Undone

How much for trans tunnel as outlined straight back to where fuel line goes thru floor? Shipping to 30530.

ksucatz · 10-23-2013, 11:55 PM

How is the roof/gutter areas? I have some rust that I need to take care of. I haven't removed all the old seam sealer yet to see the extent but know there are at least a couple holes. Might need some windshield pinch areas too.

MudBug · 10-24-2013, 11:30 AM

How much of the firewall is left? I'm looking for the door post foward.

Youey · 10-24-2013, 12:55 PM

Looking for top half of firewall where the pinch weld is makes a little
Chase for the wiring to go through I think the cowl gasket goes there for the hood. How much would it cost of that. If you need a picture ill get one

Hard_Rain420 · 10-25-2013, 10:59 AM

Here's some panels I need shipped to 32906. I can wait in line if you have other cabs available in the future.

Evaded · 10-25-2013, 03:42 PM

still was needing passenger non rusty cab corner, you never lmk...

budnikguy · 10-25-2013, 03:47 PM

Sure i could help you there...lmk what exact areas you need

Quote:

Originally Posted by ksucatz

How is the roof/gutter areas? I have some rust that I need to take care of. I haven't removed all the old seam sealer yet to see the extent but know there are at least a couple holes. Might need some windshield pinch areas too.

budnikguy · 10-25-2013, 03:48 PM

Cutting tomorrow, I will let you know what is left shortly there after

Quote:

Originally Posted by MudBug

How much of the firewall is left? I'm looking for the door post foward.

budnikguy · 10-25-2013, 03:53 PM

Sure i can help you with that, please post detailed pics of what you need.

Quote:

Originally Posted by Youey

Looking for top half of firewall where the pinch weld is makes a little
Chase for the wiring to go through I think the cowl gasket goes there for the hood. How much would it cost of that. If you need a picture ill get one

budnikguy · 10-25-2013, 03:54 PM

Still working on cuts..should get caught up this Sat-Mon...

Quote:

Originally Posted by Evaded

still was needing passenger non rusty cab corner, you never lmk...

Undone · 10-25-2013, 07:24 PM

Quote:

Originally Posted by budnikguy

$50 delivered....

I'll take it, PM payment info.

kasketrider · 10-26-2013, 12:23 AM

is the dash available? If so how much do you need for it I can pick it up and pay cash in person.

budnikguy · 10-26-2013, 03:58 PM

Dash is available, matter of fact, if you are wanting a non a/c dash I already have a clean one removed and ready to go...

Adam
951-544-0721

Quote:

Originally Posted by kasketrider

is the dash available? If so how much do you need for it I can pick it up and pay cash in person.

7dee2 · 10-27-2013, 02:16 PM

Quote:

Originally Posted by 7dee2

Adam, Any news on my Greyhound quote?

Thanks,

Adam, How's my Greyhound shipment coming?

Thanks,

budnikguy · 10-28-2013, 11:32 PM

Got rained out before I could get it packaged. I am going to try and take Thursday to catch up.

Quote:

Originally Posted by 7dee2

Adam, How's my Greyhound shipment coming?

Thanks,

7dee2 · 10-29-2013, 11:47 AM

Quote:

Originally Posted by budnikguy

Got rained out before I could get it packaged. I am going to try and take Thursday to catch up.

K LMK..

Thanks,

budnikguy · 11-01-2013, 03:36 PM

Pm'd you the Greyhound shipping cost....

Quote:

Originally Posted by 7dee2

K LMK..

Thanks,

7dee2 · 11-02-2013, 04:35 PM

Quote:

Originally Posted by budnikguy

Pm'd you the Greyhound shipping cost....

Paid via Paypal. LMK when your going to drop off it at Greyhound. Thank you Adam can't wait!!

Thanks,

Youey · 11-02-2013, 06:57 PM

Name: image.jpg
Views: 249
Size: 98.1 KB

Do you have this section left? Can you send me a price on it if still available

Undone · 11-06-2013, 09:46 PM

Quote:

Originally Posted by Undone

How much for trans tunnel as outlined straight back to where fuel line goes thru floor? Shipping to 30530.

Did this get cut and shipped?

10-20-2013, 07:32 PM	#76
Undone Registered User Join Date: Aug 2010 Location: commerce ga Posts: 896	Re: Cabs Need any cuts, parts etc?! How much for trans tunnel as outlined straight back to where fuel line goes thru floor? Shipping to 30530. Attached Images

10-23-2013, 11:03 PM	#78
Sanchez Garage Registered User Join Date: Nov 2012 Location: Woodcrest/Riverside, Ca Posts: 37	Re: Cabs Need any cuts, parts etc?! any frames? fenders ?Were in Riverside-- I am off Vanburren/canyon ridge

10-23-2013, 11:14 PM	#79
budnikguy Registered User Join Date: Sep 2007 Location: Riverside, CA Posts: 4,316	Re: Cabs Need any cuts, parts etc?! We are practically neighbors...i am on Roberts near Dauchy. I can help you with all of that. Adam

10-23-2013, 11:55 PM	#82
ksucatz Suppose to be workin........ Join Date: Jul 2001 Location: Shawnee, KS USA Posts: 164	Re: Cabs Need any cuts, parts etc?! How is the roof/gutter areas? I have some rust that I need to take care of. I haven't removed all the old seam sealer yet to see the extent but know there are at least a couple holes. Might need some windshield pinch areas too. __________________ Brent '68 C10 '70 C10 '72 LeMans "03 Trailblazer "Stupidity is like a skill, some are born with it and some develop it over a period of time."" Author unknown

10-24-2013, 11:30 AM	#83
MudBug Registered User Join Date: Jan 2007 Location: tennessee Posts: 159	Re: Cabs Need any cuts, parts etc?! How much of the firewall is left? I'm looking for the door post foward.

10-24-2013, 12:55 PM	#84
Youey Registered User Join Date: Oct 2013 Location: New Jersey Posts: 222	Re: Cabs Need any cuts, parts etc?! Looking for top half of firewall where the pinch weld is makes a little Chase for the wiring to go through I think the cowl gasket goes there for the hood. How much would it cost of that. If you need a picture ill get one

10-25-2013, 10:59 AM	#85
Hard_Rain420 Registered User Join Date: Oct 2012 Location: Melbourne FL Posts: 201	Re: Cabs Need any cuts, parts etc?! Here's some panels I need shipped to 32906. I can wait in line if you have other cabs available in the future.

10-25-2013, 03:42 PM	#86
Evaded Registered User Join Date: Apr 2013 Location: San Antonio TX Posts: 424	Re: Cabs Need any cuts, parts etc?! still was needing passenger non rusty cab corner, you never lmk... __________________ If I see a Zombie.. Im runnin it over with my Truck.

10-26-2013, 12:23 AM	#92
kasketrider Registered User Join Date: Jul 2011 Location: san diego california Posts: 22	Re: Cabs Need any cuts, parts etc?! is the dash available? If so how much do you need for it I can pick it up and pay cash in person.

11-02-2013, 06:57 PM	#99
Youey Registered User Join Date: Oct 2013 Location: New Jersey Posts: 222	Re: Cabs Need any cuts, parts etc?! Do you have this section left? Can you send me a price on it if still available



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.