1963 C-10 in NC

[1963c-10]

Originally Posted by Eric15chevys

Looks like you have been busy. I have my stuff being picked up this week and headed back down this weekend. I would love for my boys to get to see your trucks and parts sometime soon. They both love old chevys, but William likes square bodies better.

Anytime Eric....just give me a call and your welcome to come by. Bring the boys....I have enough land for them to run around on too. Maybe I can get my buddy Austin to bring his 79 square body down too!! Also.....will get the tailgate pulled for you this week.

Did your buddy decide what he wanted to do with the 230?

[WhippinSaw]

great idea for the staple replacement, keep us posted Thanks

[1963c-10]

Got a day behind on the fender closing panels. And correction on the wire gauge....its a 12 gauge aluminum wire that I use to remount the new seals to them. I drilled the staple holes out last night and hit them with one more coat of undercoating, so I can install the new rubbers and staples tonight. Will get some pics tonight.

[1963c-10]

Originally Posted by WhippinSaw

great idea for the staple replacement, keep us posted Thanks

No problem....would have been done, but my 9/64" drill bit broke day before yesterday. Got a new pack of them yesterday so all holes are enlarged and with them hanging as we speak should be good and dry by tonight. I'll use a 1/8"drill bit on the rubber so its a little tighter on the wire. Saves having to use any glue in case you have to replace the rubbers down the road. The undercoating is added protection since they always seem to have rust issues....hopefully that will eliminate the issue.

[1963c-10]

Ok, here is the rest of the closing panel resto pics....
1st thing to do is make sure the holes are large enough to except what size wire your working with. Then I measure the distance between the two holes, cut off around 2" worth of wire and make two 90* bends so you create your replacement staple. Make sure to mark and drill the two holes in the gasket also for the staple to go through. Install the staple through the gasket and then through the metal, trim to length and fold over the two tabs on the back and repeat until done. Not hard and makes a big difference.

[1963c-10]

Last of the closing panels with new seals and 2 coats of undercoating and new 12ga aluminum staples. Should last quite a long time.

[1963c-10]

Got the inner fenders prepped and undercoated also....They look kinda spotty in the pics, but the undercoating is still drying in the pics.

[1963c-10]

Got a bunch of the frame and firewall coated also this weekend in undercoating. Frames really staring to pull together. Will start frame trimming tonight or tomorrow depending on work schedule.

And my other goal for the week is to get the new seals on the inner fenders (I already have all the seals to complete the front end). They are stapled like the rest of the engine bay seals, but these are some that I will glue on since they wrap the fenders and aren't just attached on one side.

[bj383ss]

Looks good man! What brand undercoat did you use?

[1963c-10]

Originally Posted by bj383ss

Looks good man! What brand undercoat did you use?

$5.49 a can at harbor freight and it lays down great. You can adjust the texture by how close you spray. Been using it for few weeks now and real satisfied with the results. Picked up on it in one of the Jeep forums....came highly recommended.

[61K10]

Nice!!

[1963c-10]

Originally Posted by 61K10

Nice!!

Thanks...especially after seeing the job that your doing with your truck!!

[1963c-10]

Been a few weeks of off and on with both trucks. Spent a few hours yesterday in the stepside and got the interior gutted and cleaned out. Will need to do inner rockers, forward floor pans, cab corners and outer rockers. Driver side will need the cab supports also. So its time to start cutting up my donar cab and getting some metal worked in. I'll get some pics up later of whats ahead of me.

[chevy6guy9]

Doing a great job, looking good.

[61K10]

1963c-10---you are doing things top notch--every little detail is perfect. well me, i'am not quite in your zone, close maybe. Unless you do the rebuild yourself you can't splane it to others. there is a lot of exceptional people doing this here, and you are one my man!

[TJ's Chevy]

Nice work bud!

[1963c-10]

Originally Posted by chevy6guy9

Doing a great job, looking good.

Thanks bud!!

[1963c-10]

Originally Posted by 61K10

1963c-10---you are doing things top notch--every little detail is perfect. well me, i'am not quite in your zone, close maybe. Unless you do the rebuild yourself you can't splane it to others. there is a lot of exceptional people doing this here, and you are one my man!

Thank a bunch. Its going slower than I'd like, but I have a 5 day weekend starting July 4. Goal is front sheet metal off, crossmember swapped and engine set in. Should be a progressive weekend if the weather holds. I have all the parts on hand, so its just a timeline now.

[1963c-10]

Originally Posted by T.J. MCCAULEY

Nice work bud!

Thanks TJ.

[1963c-10]

Started the Captainfab hydraulic clutch / brake master conversion. Got the firewall plate undercoated, plate installed and mounted up. Just need to bore out the 1 1/2" access hole for the clutch mc. I did notch the plate so I can access the center bolt on the steering column outer clamp. Will get the rest installed after engine in this weekend. No sense risking damage to a couple of new master cylinders if I don't have to.

Thanks to Captainfab for a great product and had no fitment issues!!!!

[1963c-10]

Still trying to decide if I want to grind off the old 3 speed shift mechs from the lower column.....part of me says leave them so if I ever want to go back to a column shift I can......

[1963c-10]

Couple of pics of the floor. The rust issues are obvious, but not bad. I have definitely seen worse, but that's what I bought a welder for.

[WhippinSaw]

Thanks for the nice write up on the closing panels, I plan on doing mine this winter. The rust should be no problem, like you said "I have definitely seen worse" its also a good place to start with the new welder, on the floor under the mat, keep up the good work and keep the pictures coming, I also need to do a drivers side rocker

[1963c-10]

Originally Posted by WhippinSaw

Thanks for the nice write up on the closing panels, I plan on doing mine this winter. The rust should be no problem, like you said "I have definitely seen worse" its also a good place to start with the new welder, on the floor under the mat, keep up the good work and keep the pictures coming, I also need to do a drivers side rocker

No problem on the write up. Gives me something to do in between dry times. Also working on a write up on the other build for the conversion from manual vent to cable pull vents. A great upgrade that's not bad at all.

I agree on the welding. I have to admit, its been 15 years since I had to even turn a welder on, but I'll get back into it. I'd also rather start on the floor pans since they'll likely never be seen. I think I'll go with the full length inner rocker that has the cab corner floor on it. The tops of the inner rockers are good, but the bottom back sides are shot. It's all going to need to be cut out for floor pans and cab supports anyways. A lot of it will come from the 61 donar cab, but some of the lines that won't match up I'll order from Top Banana. I'd rather let someone who can use the OEM 61 cab floor parts on a 60-62 cab so their metal will line up. But I can use the outer rocker, maybe the inner and the cab corners.

[TheBlueBomber]

Let me know. I'm on orders down here so one night when I get off or sometime before I go home this weekend I can come over and help.