85 GMC Sierra "Scarlett"

[N2TRUX]

Last night I made a little progress. I spent time designing mounting points for the Kicker Hideaway cover. I decided to use Velcro strips so I made blocks to place the hook and loop pads on. Each one had to be sanded to fit before gluing in and clamped in place.

While the glue was drying I fine tuned the fit and finish section at a time. Each screw hole was counter sunk and a piece of a wooden toothpick was dropped in with a dab of wood glue. This gives the screw a lot more bite and allows you to get a tighter fit.

[mcbassin]

Very nice clean work on the enclosure Ken! I'd like to get a pair of small ones for my truck when you're done

[N2TRUX]

Originally Posted by mcbassin

Very nice clean work on the enclosure Ken! I'd like to get a pair of small ones for my truck when you're done

Mike what are you looking for exactly?

[mcbassin]

Originally Posted by N2TRUX

Mike what are you looking for exactly?

I'd like to have some slim enclosures to slip behind my buckets. I'm not huge on premium audio at all but right now all I have is my kick panel speakers.

[N2TRUX]

Originally Posted by mcbassin

I'd like to have some slim enclosures to slip behind my buckets. I'm not huge on premium audio at all but right now all I have is my kick panel speakers.

Message me your number so we can share some pics. I have a couple of options you might like.

[N2TRUX]

Since my plans for adding lighted acrylic on the perimeter didnt work out, I opted to go with direct LED lighting. I plan to run it around the Hideaway sub and inside the storage trays for ambience lighting. It will be hidden so the light will be a soft red glow.

[N2TRUX]

Chris and did the final fitment on the storage box. We mocked up the LED light strips and assembled once again. .
We installed the @kickeraudio
#hideaway sub back in the cab and bolted it in place. I built a raised platform that was bolted through the floor. These bolts extended through the box where the #kmc20 processor is stored. We used the mounting stud as a ground point.
All the system wires are routed around the perimeter and along the trans tunnel. They are held in place and protected by duct tape.
It's slowly going back together. I can't wait to test fire the system.

[carboncrew]

Looks great though! That box is perfect

[N2TRUX]

Originally Posted by carboncrew

Looks great though! That box is perfect

Thanks buddy, its finally taking shape.

[N2TRUX]

You would think since I mock things up in cardboard and assemble, then reassemble multiple times I wouldnt have to make serious adjustments late in the game. Unfortunately all my planning for the 6x9 boxes was off by an inch. The original design that I mocked up in cardboard was going to be very difficult to wrap and secure properly so I redesigned it a bit.

Unfortunately the new design requires me to add another inch to the box, which means subtracting an inch from each end of the Kicker Hideaway storage box. Once again, I disassembled the main box and made the necessary modifications. Now I can move forward with the Kicker 6x9 coaxial boxes.

Heres my progress from this weeks shop sessions.

[Precision Parts]

Looking great Ken!!

Did you ever get those vent assemblies re-seated?

- Derek

[N2TRUX]

Originally Posted by Precision Parts

Looking great Ken!!

Did you ever get those vent assemblies re-seated?

- Derek

Derek I have not made it to the doors yet. I have an issue with one of the rods jumping off the clip that I need to address as well. I will do a full photo coverage when I install the seals correctly.

[N2TRUX]

Saturday was another day of design changes. From my previous build, I knew the corners were difficult due to the angles and curves. I tried my best to simplify this design but it was a battle.
I ended up with a better design only to discover the trim ring and grill stuck out to far and hit the seat back. I left the shop feeling defeated.

Chris came over Sunday and finished wiring the system. I made another new front for the 6x9 enclosure. With version 4.0 I found a way to lower the speaker and recess it in the enclosure. These mods allowed the seat to clear.

Chris triple checked his work and we reconnected the battery. No sign of smoke and the #kmc20 display came to life. Even though the rear speakers arent in place Chris started the tuning process.
Big smiles and fist bumps were abundant. The Kicker Audio install was finally live and sounded fantastic already.

[aggie91]

Looks good!

[N2TRUX]

Originally Posted by aggie91

Looks good!

Thank you sir. It's starting to take shape.

[N2TRUX]

I worked late last night so shop time was limited. I spent some time gathering materials to make the passenger side enclosure for the 6x9. Tonight I get started on the construction of the box.

[N2TRUX]

Wednesday night was lay out night. I measured and cut all the pieces to build the second 6x9 box. Normally I try to cut duplicate pieces at the same when I build one side. Due to so many design changes along the way I opted to wait. With all the pieces cut, I can start assembly tonight.

[N2TRUX]

Friday night I got the second box assembled. I double checked all my measurements and couldnt understand why some of my dimensions were off. I decided to measure the back of the cab and check the angles. Can you believe that the cabs on these trucks aren't square? I know, I know, it was a huge surprise to me too. Now that I know what Im dealing with I can compensate and move on.

With the adjustments made I replaced the affected pieces and started assembly. This time the process went much quicker. I still need to refine the filler pieces, but the main structure is complete.

[Bears63]

You have some serious building talent. If I tried something like that I would just have a giant mess on my hands

[N2TRUX]

Originally Posted by Bears63

You have some serious building talent. If I tried something like that I would just have a giant mess on my hands

Trust me, my scrap pile is sometimes bigger than my keep pile. I have found that what I lack in talent, I can overcome with persistence.

[LT7A]

Originally Posted by N2TRUX

I have found that what I lack in talent, I can overcome with persistence.

Amen, brother.

[rustytruck50]

Looking great as usual....wish I could see & hear in person

[N2TRUX]

Originally Posted by rustytruck50

Looking great as usual....wish I could see & hear in person

Thanks.

[N2TRUX]

The final stage of construction on the Kicker Audio install is complete. I finished the last 6x9 #coaxial box and test fit a the pieces together.
Now it's time to sand everything smooth and prepare for wrapping them in vinyl.

[ultrahd4me]

Looks great Ken. I may have missed it, but how are mounting the speakers boxes after you wrap them. Thanks bud