Al's 71C10 Rebuild - Page 44 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

big_al_71 · 12-21-2011, 12:45 PM

Well I got up early today and went over to a local place called parker store. I bought some air line and fittings. Went to the house and fixed my left front air line and the truck is ready to go. I have to get my exhaust redone which may have to wait till january because of the holidays. we need to install the E3 leveling sensors as the wires were ran already is just a matter of mounting the sensors. I left to work earlier today but took some parting shots before I left....

Man I am so happy that this truck is off the jackstands.....

I can not Thank Raul enough for everything he did to make my truck come out the way that I always wanted........

big_al_71 · 12-21-2011, 12:52 PM

Quote:

Originally Posted by lolife99

Al,... I ran both my front air lines down the passenger side frame rail.
I connected to the passenger side bag routing the line thru the crossmember.
The drivers bag I also routed thru the crossmember under the engine.

Any time I run air line thru sheetmetal or the frame,... I run it thru a rubber grommet.
I also wrap the air line is some sleeving made by Painless Performance Products.
It helps protect the tubing from chafing.
http://www.jegs.com/webapp/wcs/store...Id=10002&Nty=0

How did you cut the air line tubing?

Keith

We were adjusting the proportioning valve and while driving around my neighborhood we went thru a lazy left turn the line just went boom we thought that the line came off the bag as the way it sounded. We looked and could not figure out how or why it got a hole on it. we are thinking that maybe we left too much slag on the line and as we were turning it got pinched so this time we made it a bit tighter. I am waiting for Raul to come back into town so that he could go over all the lines as it "SUCKED" being stuck not able to move I had to call my wife to come get me then I had to come back with a floor jack and put the hard aluminum bump so I was able to drive it back home but if that happened on the road it would not be good.
thanks for your explanation. what I am thinking is driving it to my shop and putting it on my aligment rach so that I can see what the suspension does and determine if there may be an issue when aired out or while driving.

thor · 12-21-2011, 01:38 PM

Wheels look great! I love how the fender lip comes just even with the top of the wheel. Perfect stance!

**superflysteiny** · 12-21-2011, 01:43 PM

Al you can see the line running up behind the shock tower in the first picture. I put a piece of rubber hose over it so it would not wear on the bracket.

In the last pics you can see I drilled a hole in the back of the airbag bracket put a piece of fuel line hose through the bracket and ran the airline through the hole. In to the 90 degree adapter in the bag. So the line runs from the back of the truck on the inside of the frame. Goes through the old upper shock mount hole. Behind the porter built shock bracket and throught the center of the upper bag mount to the bag. At every point that I went around a bend or through the frame I put fuel line around the airline so that it would not wear a hole in the airline. Hope this helps.

**superflysteiny** · 12-21-2011, 01:44 PM

Sorry made one mistake ran the line through old emergency cable hole not old shock mount hole. Sorry

CC69Rat · 12-21-2011, 02:05 PM

So, what's next ??

You need 'Tweety' now. A drop membered / body dropped 68, in Lambo yellow maybe ?

big_al_71 · 12-21-2011, 03:49 PM

Quote:

Originally Posted by thor

Wheels look great! I love how the fender lip comes just even with the top of the wheel. Perfect stance!

Thank you...

Quote:

Originally Posted by superflysteiny

Sorry made one mistake ran the line through old emergency cable hole not old shock mount hole. Sorry

Eric thanks for the pictures..I will use them as reference to compare to how we ran mine....

Quote:

Originally Posted by CC69Rat

So, what's next ??

You need 'Tweety' now. A drop membered / body dropped 68, in Lambo yellow maybe ?

Not a bad idea...Next project will be a "porterbuilt" body drop for sure..

class01 · 12-21-2011, 05:21 PM

Bada$$!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

dmwphoto · 12-21-2011, 06:26 PM

looks fantastic and I bet it is a blast to drive.
one small nit... that back bumper looks bent?

big_al_71 · 12-21-2011, 06:37 PM

Quote:

Originally Posted by dmwphoto

looks fantastic and I bet it is a blast to drive.
one small nit... that back bumper looks bent?

It is the picture the way it looks it is the reflection from the chrome

Quote:

Originally Posted by class01

Bada$$!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Thank you!!
Posted via Mobile Device

dmwphoto · 12-21-2011, 06:39 PM

glad to hear that. Sweet dang truck build there

crappiewrangler · 12-21-2011, 06:45 PM

Man....That is one sweet ride. It never ceases to amaze me what a set of wheels will do for the looks of a truck..Very good selection...

raull · 12-21-2011, 07:05 PM

zup bud , i got all your pix , im glad your happy , sorry i missed all the exitement on the arrival of wheels !!! im back in town so ill stop by tonite !!!

**lolife99** · 12-21-2011, 07:12 PM

Congrats again for doing a quality "make over".
I bet most would be surprised by the amount of money you layed down to do these mods.
The RideTech suspension parts, RideTech air management with the leveling system, RideTech tubular a-arms and their PRICEY MuscleBar sway bar.
Then add 20" Billet Specialties billet wheels and steering wheel.
Almost forgot the 4-wheel disc brake mods.

You did your home work and spent your money ($$$) wisely.
The results are stunning!

big_al_71 · 12-21-2011, 10:07 PM

Quote:

Originally Posted by crappiewrangler

Man....That is one sweet ride. It never ceases to amaze me what a set of wheels will do for the looks of a truck..Very good selection...

100% for sure wheels and stance make up a truck/car or it can kill it..

Quote:

Originally Posted by raull

zup bud , i got all your pix , im glad your happy , sorry i missed all the exitement on the arrival of wheels !!! im back in town so ill stop by tonite !!!

Zup brother man I am glad you came by and help me figure out why the line went last night. I am sure that now we are all set and ready to go.

Quote:

Originally Posted by lolife99

Congrats again for doing a quality "make over".
I bet most would be surprised by the amount of money you layed down to do these mods.
The RideTech suspension parts, RideTech air management with the leveling system, RideTech tubular a-arms and their PRICEY MuscleBar sway bar.
Then add 20" Billet Specialties billet wheels and steering wheel.
Almost forgot the 4-wheel disc brake mods.

You did your home work and spent your money ($$$) wisely.
The results are stunning!

Keith thanks for all your help as usual..I definetly spent a great chunk on $$$ this time around let alone in the whole truck since we started in 2008 and remember that 90% of all the labor was done in house by friends and I so I saved alot of $$ on labor..

I am still not done as I have many misc items that i want to replace just because of wear and not up to the standards of what i want to accomplish.

I AM EXTREMELY GRATEFUL TO MY BUDDY HARRY, JOHNNY AND RAUL WITHOUT THESE GUYS THIS TRUCK WOULD NOT HAD BEEN BUILT.

HarrySmith · 12-21-2011, 10:15 PM

Looks awesome man! Thats what we should have done from the start!
Glad I was a part of it, wish I was there for this!

msgross · 12-21-2011, 10:15 PM

I likey...

bobshotrodblazer · 12-21-2011, 10:16 PM

Truck rocks Al, Good job.

hayhauler71 · 12-21-2011, 10:25 PM

Looks great Al a job well done

big_al_71 · 12-21-2011, 10:31 PM

Quote:

Originally Posted by HarrySmith

Looks awesome man! Thats what we should have done from the start!
Glad I was a part of it, wish I was there for this!

This has gone thru my head a thousand times I should had listened to you out of the gate. As you know that I am super grateful to you for EVERYTHING you did for me.
Thanks bro!!!!

Quote:

Originally Posted by msgross

I likey...

Thanks Big Mike!!!

Quote:

Originally Posted by bobshotrodblazer

Truck rocks Al, Good job.

thanks Bob!!!!!

Quote:

Originally Posted by hayhauler71

Looks great Al a job well done

thanks Fuzzy....

**N2TRUX** · 12-21-2011, 11:48 PM

Dude your truck looked "good" before, and now it freakin rocks. Your investment paid big dividends.....

big_al_71 · 12-22-2011, 12:24 AM

Quote:

Originally Posted by N2TRUX

Dude your truck looked "good" before, and now it freakin rocks. Your investment paid big dividends.....

Thank you Ken!!!!!!!!

PTS · 12-22-2011, 12:24 AM

Hey Al,

Did you find the shank lugs? Also I am looking for a swb fleetside bed only for a 67-72. Let me know on the lugs and the bed when you get a chance. Also did you post pictures of your truck on Pro Touring?

Regards,

Perry
PTS

big_al_71 · 12-22-2011, 12:30 AM

Quote:

Originally Posted by PTS

Hey Al,

Did you find the shank lugs? Also I am looking for a swb fleetside bed only for a 67-72. Let me know on the lugs and the bed when you get a chance. Also did you post pictures of your truck on Pro Touring?

Regards,

Perry
PTS

Hey Perry
Yes I found the lugs at wheel world down the road from my shop and I already installed them.
also take a look at this link

http://www.pro-touring.com/showthrea...529#post865529

Thanks for everything I will keep an eye out for a swb bed for you....

nibs · 12-22-2011, 02:59 AM

Hey Al, Im curious about the wheel clearances on your fronts. Im talking to Perry about some Intros and Id love to hear some feedback from how much room you have with yours...

An Im amazed at the drastic change your truck has made! I know how you feel about how much was spent and the changes it gives you. I just bought a front dropmember and some rear goodies from Nate. All that money that nobody will be able to see! LOL

Keep up the good work

12-21-2011, 12:45 PM	#1076
big_al_71 Registered User Join Date: Jun 2008 Location: South Florida Posts: 11,375	Re: Al's 71C10 Rebuild Well I got up early today and went over to a local place called parker store. I bought some air line and fittings. Went to the house and fixed my left front air line and the truck is ready to go. I have to get my exhaust redone which may have to wait till january because of the holidays. we need to install the E3 leveling sensors as the wires were ran already is just a matter of mounting the sensors. I left to work earlier today but took some parting shots before I left.... Man I am so happy that this truck is off the jackstands..... I can not Thank Raul enough for everything he did to make my truck come out the way that I always wanted........ Attached Images __________________ Get your facts first, and then you can distort them as much as you please!!!!!. Sylvester's build thread >>>http://67-72chevytrucks.com/vboard/s...ht=big+rebuild

12-21-2011, 01:38 PM	#1078
thor Registered User Join Date: Apr 2008 Location: Redmond, WA Posts: 679	Re: Al's 71C10 Rebuild Wheels look great! I love how the fender lip comes just even with the top of the wheel. Perfect stance! __________________ 1972 Chevy Blazer CST.....Project: Polished Turd

12-21-2011, 01:43 PM	#1079
superflysteiny Senior Member Join Date: Nov 2008 Location: orangevale ca Posts: 4,630	Re: Al's 71C10 Rebuild Al you can see the line running up behind the shock tower in the first picture. I put a piece of rubber hose over it so it would not wear on the bracket. In the last pics you can see I drilled a hole in the back of the airbag bracket put a piece of fuel line hose through the bracket and ran the airline through the hole. In to the 90 degree adapter in the bag. So the line runs from the back of the truck on the inside of the frame. Goes through the old upper shock mount hole. Behind the porter built shock bracket and throught the center of the upper bag mount to the bag. At every point that I went around a bend or through the frame I put fuel line around the airline so that it would not wear a hole in the airline. Hope this helps. __________________ Tootsie build T Shirts (Supporting Colon Cancer research) Tootsie- a truck for my mother Pops 72 Cheyenne Dropmember build 67 Second Chance project from hell

12-21-2011, 01:44 PM	#1080
superflysteiny Senior Member Join Date: Nov 2008 Location: orangevale ca Posts: 4,630	Re: Al's 71C10 Rebuild Sorry made one mistake ran the line through old emergency cable hole not old shock mount hole. Sorry __________________ Tootsie build T Shirts (Supporting Colon Cancer research) Tootsie- a truck for my mother Pops 72 Cheyenne Dropmember build 67 Second Chance project from hell

12-21-2011, 02:05 PM	#1081
CC69Rat Registered User Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,212	Re: Al's 71C10 Rebuild So, what's next ?? You need 'Tweety' now. A drop membered / body dropped 68, in Lambo yellow maybe ? __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

12-21-2011, 05:21 PM	#1083
class01 Registered User Join Date: Jul 2007 Location: Utah Posts: 295	Re: Al's 71C10 Rebuild Bada$$!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

12-21-2011, 06:26 PM	#1084
dmwphoto Registered User Join Date: Sep 2010 Location: Richmond, Va Posts: 573	Re: Al's 71C10 Rebuild looks fantastic and I bet it is a blast to drive. one small nit... that back bumper looks bent?

12-21-2011, 06:39 PM	#1086
dmwphoto Registered User Join Date: Sep 2010 Location: Richmond, Va Posts: 573	Re: Al's 71C10 Rebuild glad to hear that. Sweet dang truck build there

12-21-2011, 06:45 PM	#1087
crappiewrangler Registered User Join Date: Jul 2011 Location: Athens, AL Posts: 42	Re: Al's 71C10 Rebuild Man....That is one sweet ride. It never ceases to amaze me what a set of wheels will do for the looks of a truck..Very good selection...

12-21-2011, 07:05 PM	#1088
raull Registered User Join Date: Mar 2009 Location: miramar florida Posts: 1,232	Re: Al's 71C10 Rebuild zup bud , i got all your pix , im glad your happy , sorry i missed all the exitement on the arrival of wheels !!! im back in town so ill stop by tonite !!! __________________ check out my build thread 71 c/10 step side 5.3 twin turbo http://67-72chevytrucks.com/vboard/s...d.php?t=485320 raul

12-21-2011, 07:12 PM	#1089
lolife99 67-72 parts collector,… Join Date: Nov 2002 Location: Mid-MO Posts: 22,700	Re: Al's 71C10 Rebuild Congrats again for doing a quality "make over". I bet most would be surprised by the amount of money you layed down to do these mods. The RideTech suspension parts, RideTech air management with the leveling system, RideTech tubular a-arms and their PRICEY MuscleBar sway bar. Then add 20" Billet Specialties billet wheels and steering wheel. Almost forgot the 4-wheel disc brake mods. You did your home work and spent your money ($$$) wisely. The results are stunning! __________________ Keith Convert to disc brakes. http://67-72chevytrucks.com/vboard/s...d.php?t=444823

12-21-2011, 10:15 PM	#1091
HarrySmith Registered User Join Date: Nov 2011 Location: Coral Springs, FL Posts: 22	Re: Al's 71C10 Rebuild Looks awesome man! Thats what we should have done from the start! Glad I was a part of it, wish I was there for this!

12-21-2011, 10:15 PM	#1092
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: Al's 71C10 Rebuild I likey... __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer"

12-21-2011, 10:16 PM	#1093
bobshotrodblazer BigBlockBobby Join Date: Mar 2004 Location: Lake Worth, Florida Posts: 740	Re: Al's 71C10 Rebuild Truck rocks Al, Good job. __________________ Bob

12-21-2011, 10:25 PM	#1094
hayhauler71 Registered User Join Date: Aug 2009 Location: St. Paul MN. Posts: 1,996	Re: Al's 71C10 Rebuild Looks great Al a job well done __________________ Fuzzy



Register or Log In To remove these advertisements.

12-21-2011, 11:48 PM	#1096
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,023	Re: Al's 71C10 Rebuild Dude your truck looked "good" before, and now it freakin rocks. Your investment paid big dividends..... __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

12-22-2011, 12:24 AM	#1098
PTS Junior Member Join Date: Nov 2005 Location: Roswell, N.M. Posts: 241	Re: Al's 71C10 Rebuild Hey Al, Did you find the shank lugs? Also I am looking for a swb fleetside bed only for a 67-72. Let me know on the lugs and the bed when you get a chance. Also did you post pictures of your truck on Pro Touring? Regards, Perry PTS __________________ Great Deals for 67-72 members on Billet Specialties, Intro Wheels, and Ridetech! Toll Free 1-855-353-7885

12-22-2011, 02:59 AM	#1100
nibs JRods Garage Join Date: Dec 2009 Location: East Highland, CA Posts: 1,098	Re: Al's 71C10 Rebuild Hey Al, Im curious about the wheel clearances on your fronts. Im talking to Perry about some Intros and Id love to hear some feedback from how much room you have with yours... An Im amazed at the drastic change your truck has made! I know how you feel about how much was spent and the changes it gives you. I just bought a front dropmember and some rear goodies from Nate. All that money that nobody will be able to see! LOL Keep up the good work __________________ Orange Julius-My dropmember'd, LS'd, SWB street machine...

Register or Log In To remove these advertisements.