slik ricks 67 short wide CST

[67chevy1series]

thanks jeremy!!!!!i got my parts today it wasnt just a shift linkage and engine harness! there was also some really cool spark plug wire holders! 2 groove water pump pullie and another wire(s) that i have no clue where they go i will take pics in a sec!

[jbclassix]

The plug wire holders are factory since you are going that way. They go on the back of the engine. The odd wire should be for your TH350 reverse light... I think. The pulley was the one off my 70... I think I remember you saying you needed one

[67chevy1series]

yes i did need it do you have any pics of where the wirte and those plug holders go? i am going to sand the pullie and the plug holders down an dpaint them i am going to upload the pics now........

i think you gave me 4wd automatic 350 shift linkage is there a difference?

[67chevy1series]

here are pics

[jbclassix]

Well that sucks! I had a different short WP. And you can see that the INNER groove is what the 69-7? alt belt rode on.



I posted a picture of the outside of the frame where the bracket bolts to.

I had to turn the pivot bolt 180 to get the rod to fit in the tube.

Not 100% sure, but if you look in the upper left corner, between the heater box and firewall tunnel, I think that connector goes on that switch


I'm gonna have to dig further and see what i can find in my pictures. I'm getting ready for Church right now, so it will be later.

Super bummer on the parts!!!

Edit: The single hole one was on the left rear intake manifold bolt the 2 hole one was on the right rear 2 intake manifold bolts

[JasonBird]

looking good there Rick!

[67chevy1series]

Originally Posted by jbclassix

Well that sucks! I had a different short WP. And you can see that the INNER groove is what the 69-7? alt belt rode on.



I posted a picture of the outside of the frame where the bracket bolts to.

I had to turn the pivot bolt 180 to get the rod to fit in the tube.

Not 100% sure, but if you look in the upper left corner, between the heater box and firewall tunnel, I think that connector goes on that switch


I'm gonna have to dig further and see what i can find in my pictures. I'm getting ready for Church right now, so it will be later.

Super bummer on the parts!!!

Edit: The single hole one was on the left rear intake manifold bolt the 2 hole one was on the right rear 2 intake manifold bolts

its okay at least i can still use most of the parts! i need to figure out where the spark plug wire holders go i cleaned them and painted them black.... that extra wire that connects on the firewall .... i dont have that switch on the fire wall .... remember i have a 67 and the fire wall is different right there

Originally Posted by JasonBird

looking good there Rick!

thanks jason! i need to get a couple more things and i sholud be ready for my first start up!

[67chevy1series]

UPDATE i finally decided to take the driver bucket out and get the rewst of the old rivets off and put my adjuster lever on for the first time ..... and i had forgotten about tha surface rust that was on the tracks so i got the buffer out and buffed them down to really nice metal and whaala! primer......paint.........install! it works!






any body know where i can get a ball with threads ? i have a 1/2 inch thick round stock and i want to thread the end of it and screw the ball on so if any body knows where i can get one LMK

[usmcchevy]

Originally Posted by 67chevy1series

any body know where i can get a ball with threads ? i have a 1/2 inch thick round stock and i want to thread the end of it and screw the ball on so if any body knows where i can get one LMK

http://www.mcmaster.com/#ball-knobs/=b0bsen

[67chevy1series]

thanks i wonder if there are any local shops that i can deal with

[2manyprojects]

Originally Posted by 67chevy1series

UPDATE i finally decided to take the driver bucket out and get the rewst of the old rivets off and put my adjuster lever on for the first time ..... and i had forgotten about tha surface rust that was on the tracks so i got the buffer out and buffed them down to really nice metal and whaala! primer......paint.........install! it works!






any body know where i can get a ball with threads ? i have a 1/2 inch thick round stock and i want to thread the end of it and screw the ball on so if any body knows where i can get one LMK

You might try a hydraulic supply store control levers usually have small knobs.

I sent you a PM the other day about the parts if you haven't seen it.

[67chevy1series]

hmmmm let me check my pms....

[67chevy1series]

Originally Posted by 2manyprojects

You might try a hydraulic supply store control levers usually have small knobs.

I sent you a PM the other day about the parts if you haven't seen it.

thats a good idea what about a tractor supply co.?

[jbclassix]

Sorry, thats what my edit was... the single hole wire loom goes on the left rear intake manifold bolt. the 2 hole one goes on the two right rear intake manifold bolts.

[67chevy1series]

oh ok thanks i am going to need to get some longer bolts then......

[2manyprojects]

Originally Posted by 67chevy1series

thats a good idea what about a tractor supply co.?

Tractor Supply might have something. Or if you have a heavy equipment shop close they might have something laying around or can tell you where to go. I used to have a drawer full of them I just threw away.

[67chevy1series]

haha thats just my luck! i dont have any major equip. shops but i do have a local tractor supply co.

[project 67 sub]

here is a question for you. whats going on with all of those washers stacked under the front bolts of your wiper cowl, did it not line up right without them lol.???

[67chevy1series]

hmmm....oh yea it was a test to see if i could get it to go higher to met the hood ....its pretty ''ghetto'' but you gotta give me some credit, if you cant make the hood meet the cowl panel then make the cowl panel come up a little to meet the hood! but i enede up taking them out and i need to do some adj to the hood still.... any more questions from any body?

[project 67 sub]

haha nope lol was just making sure

[67chevy1series]

oh alrighty then eric

[oldblue1968chevy]

Ya trying to make a knob? Once I drilled a golf ball and used it for a suicide shifter..lol

[67chevy1series]

hahaha thats funny. well today i will get some pics for you guy, and me and my dad are gonna change his head gate his is completely rusted through in the middle where it bends, so we have one that is perfect and it wil go on instead

[Newtz67]

Hey Rick, for that threaded ball you might try N&S tractor supply. They used to be out off of 59 past the fairgrounds. I think there are a couple others out there too, not 100% percent sure but it may be worth a shot. Good luck!

[67chevy1series]

thanks newtz!