The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1960 - 1966 Chevrolet & GMC Pickups Message Board > projects and builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-05-2017, 09:28 PM   #101
LostMy65
But Found Her 25yrs Later!
 
LostMy65's Avatar
 
Join Date: Oct 2010
Location: Oregon City, Oregon
Posts: 10,527
Re: 1966 C1434 SWB Custom Cab

I'll be watching...
__________________
I lost my 65 - Found it 25 years later:
http://67-72chevytrucks.com/vboard/s...d.php?t=426650

66 C20 Service Truck:
http://67-72chevytrucks.com/vboard/s...d.php?t=428035
LostMy65 is offline   Reply With Quote
Old 10-13-2017, 06:38 PM   #102
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Smile Re: 1966 C1434 SWB Custom Cab

Motor mount plates are made and installed. now on to the tranny cross member. I know I'm re- inventing the wheel here but it's more satisfying when you make your own parts
Attached Images
 
CustomCab66 is offline   Reply With Quote
Old 10-14-2017, 08:23 AM   #103
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Angry Re: 1966 C1434 SWB Custom Cab

If I didn't have bad luck I wouldn't have any luck at all. Tapping out one last hole for 3/8-16 and broke the tap. Hope I can weld to it and get it out otherwise I will need to redo that whole plate :/
Attached Images
 
CustomCab66 is offline   Reply With Quote
Old 10-14-2017, 09:04 PM   #104
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Re: 1966 C1434 SWB Custom Cab

So I came across a little luck because was able to remove the broken tap. Happy to say the motor is in there all bolted up. With the hoist out of the way I'll be able to start the tranny mount, oil cooling lines, fuel lines and connections
Attached Images
 
CustomCab66 is offline   Reply With Quote
Old 10-15-2017, 07:25 PM   #105
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Re: 1966 C1434 SWB Custom Cab

Doesn't look like a tranny crossmember yet but I know there's one there somewhere. 👍🏽
Attached Images
 
CustomCab66 is offline   Reply With Quote
Old 10-19-2017, 09:42 PM   #106
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Re: 1966 C1434 SWB Custom Cab

Transmission crossmember taking shape.
Attached Images
 
CustomCab66 is offline   Reply With Quote
Old 10-20-2017, 11:01 AM   #107
scdude37
Registered User
 
Join Date: Oct 2016
Location: Hernando, MS
Posts: 16
Re: 1966 C1434 SWB Custom Cab

love seeing this project. Like seeing the 5.3 coming together and the progress on it. I would like to swap mine out sometime to the same thing you are running.
scdude37 is offline   Reply With Quote
Old 10-23-2017, 09:44 PM   #108
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Re: 1966 C1434 SWB Custom Cab

Thanks, the progress is not quite as fast as I'd hoped but I'll get it evenually
CustomCab66 is offline   Reply With Quote
Old 10-23-2017, 09:49 PM   #109
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Re: 1966 C1434 SWB Custom Cab

I have the center mount tack welded in place right in the middle so time for test fit #1. So far right in track
Attached Images
  
CustomCab66 is offline   Reply With Quote
Old 10-24-2017, 01:50 PM   #110
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Re: 1966 C1434 SWB Custom Cab

I removed the center of the arches and from there I'll Just go straight to the frame. Welding it out now so all I need is about 3 inches of straight pipe on each side. To Be Continued
Attached Images
 
CustomCab66 is offline   Reply With Quote
Old 10-24-2017, 02:01 PM   #111
53chevyforever
Registered User
 
53chevyforever's Avatar
 
Join Date: Jul 2010
Location: texas
Posts: 180
Re: 1966 C1434 SWB Custom Cab

Quote:
Originally Posted by duallyjams View Post
super nice
you can add a vacuum gauge to fill out the gauge panel
Attachment 1303930
Here is mine.
Attached Images
 
53chevyforever is offline   Reply With Quote
Old 10-27-2017, 03:53 PM   #112
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Re: 1966 C1434 SWB Custom Cab

Quote:
Originally Posted by 53chevyforever View Post
Here is mine.
Nice!!! I want a Vac gauge
CustomCab66 is offline   Reply With Quote
Old 10-27-2017, 03:59 PM   #113
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Re: 1966 C1434 SWB Custom Cab

Headers are here and they fit!!!!! Wow impressed with them so far. These are the LS swap header for C-10 trucks from Speed engineering specifically for 60-66. Not bad for headers made for these trucks with an LS.
Attached Images
   

Last edited by CustomCab66; 10-28-2017 at 12:03 PM.
CustomCab66 is offline   Reply With Quote
Old 10-27-2017, 04:14 PM   #114
bj383ss
Registered User
 
bj383ss's Avatar
 
Join Date: Sep 2012
Location: Leander, TX
Posts: 969
Re: 1966 C1434 SWB Custom Cab

Those look really good man!

Bret
__________________
64' Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=586955
bj383ss is offline   Reply With Quote
Old 10-27-2017, 05:54 PM   #115
53chevyforever
Registered User
 
53chevyforever's Avatar
 
Join Date: Jul 2010
Location: texas
Posts: 180
Re: 1966 C1434 SWB Custom Cab

Quote:
Originally Posted by CustomCab66 View Post
Headers are here and they fit!!!!! Wow impressed with them so far.
Awesome headers!
53chevyforever is offline   Reply With Quote
Old 10-28-2017, 04:08 PM   #116
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Talking Re: 1966 C1434 SWB Custom Cab

Now that the headers fit I'm back on the tranny mount, now I have it the width of the frame. Notice I cut the humps off and ran it straight out from there to the frame. It should end up in the center of the frame rail. Frame is 29 inches from the inside of one frame rail to the other. All that's left is to fab the mounting plates that I'm gonna use to secure it to the frame
Attached Images
 
CustomCab66 is offline   Reply With Quote
Old 11-02-2017, 09:49 PM   #117
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Re: 1966 C1434 SWB Custom Cab

No pictures this time. I'm gonna try and run my driveshaft down to scotty's drivetrain and machine here in Austin. Those guys said they would shorten the driveshaft for 89. They tack on more for new u joints and balance job. I'll have them spin it first to see if it is even worth even messing with it or if the tube needs to be replaced.
CustomCab66 is offline   Reply With Quote
Old 11-11-2017, 11:00 AM   #118
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Re: 1966 C1434 SWB Custom Cab

My LS has a drive by wire throttle body. I'm debating where I want the wiring at this point but I mounted the pedal assembly on the floor where the wires feed the tail lamps. I cut the pedal off of the pedal switch and welded a piece of the original pedal fulcrum to it. I pushed the pedal and it moves freely the entire rotation of the throttle switch. I've been warned when welding on items with electronics that the arc surge will cook the electric circuit. Tip is to ground as close to the area that needs to be welded so I used the ground clamp to hold my peices together. Cooled them shortly after in some water to prevent heat damage to the switch. Hope it will work
Attached Images
 
CustomCab66 is offline   Reply With Quote
Old 11-17-2017, 02:19 PM   #119
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Re: 1966 C1434 SWB Custom Cab

He biggest hurdle in this whole swap has been the tranny mount itself. I checked the frame side to side checked the driveline angle over and over. None of the original holes in the frame are square, the driveshaft loop same. Blah blah blah. Over and over. So I eyeballed it so that the mount looks square with the tranny itself with the motor bolted down. I centered the tailshaft of the tranny between the frame rails and boxed the frame in. Drilled the mounting hole and welded nuts inside the boxed section. This will aid in removing the cross member in the future because I will not need a back up wrench. Hope it all works out. If I made it square it would have looked bad out of square. Only time will tell
Attached Images
  

Last edited by CustomCab66; 11-18-2017 at 09:31 AM.
CustomCab66 is offline   Reply With Quote
Old 11-18-2017, 10:21 PM   #120
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Re: 1966 C1434 SWB Custom Cab

Separated the motor from the transmission so I could replace the front and rear main gaskets and seals and the pan gasket. So far so good
Attached Images
 
CustomCab66 is offline   Reply With Quote
Old 11-20-2017, 08:13 PM   #121
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Re: 1966 C1434 SWB Custom Cab

Splashed a fresh coat of VHT black engine paint on the lower portion of the block. I found out that the rear cover had stripped bolt hole bosses on the oil pan flange. Got a NOS part coming from EBay. Do it slow and you know it's right
Attached Images
  
CustomCab66 is offline   Reply With Quote
Old 11-22-2017, 08:01 PM   #122
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Re: 1966 C1434 SWB Custom Cab

My rear cover showed up today so I finished sealing up the motor. Got ahead of myself and before I knew it I had it back in the truck. Time to start with all the small stuff like wiring and plumbing the tranny lines.
Attached Images
 
CustomCab66 is offline   Reply With Quote
Old 11-23-2017, 08:44 AM   #123
northern 85
Registered User
 
northern 85's Avatar
 
Join Date: Mar 2005
Location: Fairfield Maine
Posts: 1,759
Re: 1966 C1434 SWB Custom Cab

Looking good!!!
northern 85 is offline   Reply With Quote
Old 11-25-2017, 10:54 AM   #124
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Re: 1966 C1434 SWB Custom Cab

So wiring day is close. I used the instructional at LS1 Swap.com to convert the original harness to a stand alone harness back when I first bout the LS combo. Yesterday I installed the harness and hooked up all the sensor related stuff in the engine compartment. I ran the harness into the cab using a stock grommet hole for the original engine harness. Time to bust out the soldering iron and shrink wrap
Attached Images
   
CustomCab66 is offline   Reply With Quote
Old 11-25-2017, 11:00 AM   #125
CustomCab66
Senior Member
 
CustomCab66's Avatar
 
Join Date: Aug 2014
Location: Cedar Park, Texas
Posts: 326
Re: 1966 C1434 SWB Custom Cab

Also I have the pre and post fuel filters and necessary fittings on the way from Summit Racing. To Be Continued
CustomCab66 is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:30 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com