New member with a 1960

[forestb]

I can't wait to see how these turn out. How do they deal with the notch in the window opening where the vent window post used to go?

Originally Posted by The1960APE

My windows arrived from classic truck glass. They too are very nice, the lower tracks are pre fastened to the glass. So far I am VERY pleased with the quality of the kit!

[The1960APE]

Originally Posted by forestb

I can't wait to see how these turn out. How do they deal with the notch in the window opening where the vent window post used to go?

There is no notch in my doors it's all flush.

[The1960APE]

A little progress

[The1960APE]

We are making a little bit of progress, the machine work is finished, the engine should be together in the next 2 weeks, transmission is finished... Now if we can get the patch panels finished up it will be time to do some mockup!

[DPowers]

Looks good.

[The1960APE]

Originally Posted by DPowers

Looks good.

Thank you sir!

[The1960APE]

Things are still creeping right along!

[flashed]

Nice seats and a very cool table too.

[The1960APE]

I never realized how small the cab is on these trucks, being 6'4 this is going to be a challenge, I am going to have to order another steering wheel with less offset, and I am considering cutting the "roll" out from under the rear window...

[The1960APE]

Well, the seats pictured are gone, I am going another route! We are slowly working on replacing the missing metal...LOL, The engine is coming right along, tranny is finished, and I am about to jump on the power window install!

[forestb]

What type of leather on those seats?

[The1960APE]

Originally Posted by forestb

What type of leather on those seats?

Chyenne Stirrup from Carrol leather

[DPowers]

Quite the engine there- nice

[The1960APE]

Thank you, I am having one heck of a time finding the parts to install this into my 61, I cannot seem to get a straight answer from anywhere!

[62CiscoKid]

The info is around but it seems we'll have to dig it up...unfortunately T-Bar trucks have different frames than the later trucks that do have mounts made for them. Our frames are narrower and have shorter C channels. In some cases like my GMC the frame is boxed and possibly thicker.

Some have gotten away with notching the frame with later model mounts and other have simply had to spacer the top of the mounts. I'm currently having issues with my POL mounts, but when I get it figured out, I'll post what I come up with.

There doesn't seem to be a "bolt on" solution.

Header clearance is another issue and since I'm not building a race truck the long tube and big diameter headers don't interest me. That might be the case for your motor though. Lookin damn fine BTW.

-Joe

[Captainfab]

The closest fitting factory engine mount brackets for the '60-'62 frames are the '67-'72 small block engine mount brackets. Although some say they had to add a .250" spacer on top of the frame. Then you will need the '63-'72 engine mounts and an adapter plate for the LSx engine. Other than those, I do not know of any off the shelf engine mount solutions. Depending on just what you are wanting, the engine mounts might just have to be custom fabricated.

This is one of the reasons I don't care for the '60-'62 frames.

Originally Posted by The1960APE

Thank you, I am having one heck of a time finding the parts to install this into my 61, I cannot seem to get a straight answer from anywhere!

[The1960APE]

Originally Posted by Captainfab

The closest fitting factory engine mount brackets for the '60-'62 frames are the '67-'72 small block engine mount brackets. Although some say they had to add a .250" spacer on top of the frame. Then you will need the '63-'72 engine mounts and an adapter plate for the LSx engine. Other than those, I do not know of any off the shelf engine mount solutions. Depending on just what you are wanting, the engine mounts might just have to be custom fabricated.

This is one of the reasons I don't care for the '60-'62 frames.

Thanks for the advice, that's exactly what we ended up doing.....

[The1960APE]

I really like POR-15 but wasn't happy with the firewall finish using POR-15, I took it down to the metal, primed it, sanded and shot it with a Jet black acrylic enamel. I'm much happier, once it cures I will wet sand and buff it out.
My 65 Olds project is about to come to a close, so its full steam ahead on the Apache....

[The1960APE]

Originally Posted by Captainfab

The closest fitting factory engine mount brackets for the '60-'62 frames are the '67-'72 small block engine mount brackets. Although some say they had to add a .250" spacer on top of the frame. Then you will need the '63-'72 engine mounts and an adapter plate for the LSx engine. Other than those, I do not know of any off the shelf engine mount solutions. Depending on just what you are wanting, the engine mounts might just have to be custom fabricated.

This is one of the reasons I don't care for the '60-'62 frames.

We ended up modifying the mounts sent by CPP, I didn't like how their mount kit had the engine sitting, it was way to high for my taste! So we did use them just made some adjustments and lowered the engine down a bit!

[mb63Chevy]

WOW Some ruff tough trucks here - Mine and Org 63 Like to know what it may sell for?
63 Calf Black tags new paint work all org 283V8 3 speed with OD Custom.[IMG]C:\Users\burbom\Pictures\Back G Photos[/IMG]

[DPowers]

Very nice.
You going down to the Maggie Valley show next weeK?

[The1960APE]

Originally Posted by DPowers

Very nice.
You going down to the Maggie Valley show next weeK?

Yes Sir,
I will defiantly be there! Are you going? What are you taking?

[DPowers]

Quite a bit of stuff.
64-66 and 60-63 doors, GMC Hood and Chevy 64-66 Hood, complete dashs for '62, 64-66 and a GMC. Barn and Clamshell doors. Rat Rod step bed as well as some other goodies.

[The1960APE]

I'd love to find some nice chrome turn signal bezels...

[The1960APE]

The front windshield and wheel tubs came in today, I ordered Mobsteel (Detroit steel) wheels today, 20x11 & 20x8 and tires Nitto 245/40/20 & 315/35/20.
The engine has been mocked up and will be in place soon! We are having to cut and modify the Torsion bar cross member for clearance of the 4L80E but its all working out nicely!