1964-1966 center a/c vent

[argonaut]

I'm ready for a complete assembly once you have them. Are you planning to make any sort on plenum with a duct connection for the back side? I would want one as my application is custom, not using the factory AC system.

[corvettejim1968]

After the first wave of complete units. my intention is to replicate the ductwork behind the vent inside the dash.

[chevyrestoguy]

Originally Posted by corvettejim1968

After the first wave of complete units. my intention is to replicate the ductwork behind the vent inside the dash.

Jim-
If you need an original duct to use as a pattern to make your new one, PM me.

[corvettejim1968]

thank you for the offer. i do have one. this might take some time because its big and im not sure i can even make one yet. the small parts are not so bad.

Jim

[earl84]

corvettejim1968, these things are works of art. You are doing a great job and I sincerely hope you make a lot of money filling this void in the 60-66 Chevy truck market.

[corvettejim1968]

i had no intention of selling the vents raw (not chromed) but if for some reason you wanted them i can sell them at $25 each. or you can wait a couple months for the chromed ones at $50 each.

some seller on ebay said he is spending $75 per vent to have them stripped and rechromed. that sounds like alot to me.

[ChefCy]

so nice!!!

[ms2335]

I am in for two ball vents and the center vent as soon as ready

[corvettejim1968]

i ordered a set of these vents this morning. when the come in i will cut out the center and add in our "correct" truck vent ball center and then cast that part and offer 2 1/2in vent balls for the sides of the dash for that custom but yet look like it came factory look. this is what im doing to my truck someday.
http://nostalgicac.com/2-5-inch-chro...hree-vein.html

[nsb29]

looks like things are moving rite along just wonted to let you know im looking forward to receiving my complete unit DOUG

[aggie91]

Just found this thread. Your work is top notch. Seems like a fair investment and the parts look good. Maybe some day I can get a complete set up from you.

[SFTorange]

Nice work! I'll definitely be watching the progress on these!

[corvettejim1968]

I'm sending off 4 round ball vents and one center vent to be chromed. I was told resin casted parts are harder to Chrome because of the mold release. so I had to soak them in purple power and then spray them off with carburetor cleaner. the chrome guy told me after that then I need to do a test with scotch tape to see how well it sticks. all is good on my end let's see how they turn out. unfortunately it's a five week turnaround but when I get them back I will have one complete ready to sell. after this first test I will make a whole bunch more so everybody gets one I have 11 people on my list so far let me know if you want a complete assembly and I will put you on the list.

[aggie91]

That smaller vent looks good.

I did a little online research on resin casting, just a question for you, what material are you using for the parts and for making the molds?

[corvettejim1968]

Originally Posted by aggie91

That smaller vent looks good.

I did a little online research on resin casting, just a question for you, what material are you using for the parts and for making the molds?

to make the part its a 2 part resin. i dont know the brand

and the silicone is a 2 part also.

[nsb29]

you think heed tell you aggie

[corvettejim1968]

okay got the first small "stock looking" vent ball done a few minutes ago. turned out great. i put one drop of red dye just to mark it as #1



what is was and what it will be

[aggie91]

Originally Posted by nsb29

you think heed tell you aggie

He did tell me in post 125.

[chad64chevy]

the side vents look great! so if the complete center is $300 what is it with the smaller vents? wondering what a total setup is going to cost me!!

[corvettejim1968]

Originally Posted by chad64chevy

the side vents look great! so if the complete center is $300 what is it with the smaller vents? wondering what a total setup is going to cost me!!

im not sure just yet but for a complete set it will be a little cheaper than buying a piece at a time. most of my cost comes from having the parts chromed and the shipping.

[corvettejim1968]

i made the first half of the smaller vent ball mold over the weekend. i should be able to finish up the top half next Sunday.

[ms2335]

LOOKS GREAT!!! Can't wait to get mine. Guess now I need the three vents for the center faceplate and two side vents when available.

[Budman56]

corvettejim1968 I don't know how I miss this thread, But I got to say your the man....... these look great! this does give me some ideals. I do have one question where did you get your vent balls chromed?

[K5 Addiction]

This is awesome! Excellent work. I just shared this link with a friend at Vintage air as this would be an amazing addition to their sure fit kits. I would love to see a complete modern AC kit with the original vent. Fantastic work stepping up & filling the void in the market. I know it will pay off for you.

[aggie91]

That red ball looks kinda neat in the housing. Could you do them in Black to save on getting them chromed if someone whated that option?