What did you do to your truck today part III - Page 52 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Pappyx3! · 07-07-2015, 09:16 PM

Finally! Got the engine in on the 62. Planning to fire it up on Thursday evening.

TJ's Chevy · 07-07-2015, 09:21 PM

Quote:

Originally Posted by Pappyx3!

Finally! Got the engine in on the 62. Planning to fire it up on Thursday evening.

Lugnutz65 · 07-07-2015, 09:58 PM

Repaired the pitted and rusted portion of the bed rear cross sill.

HappyHooligan · 07-08-2015, 09:44 AM

Replaced Speedo Driven gear, watched needle bounce around and then slowly down to nothing.

Rebuilt Rag Joint on steering shaft..... twice.
First try Steering wheel was upside down

Replaced fuel sending unit Float. brass one was cracked. Checked ohms on sending unit and continuity to dash and ground. No movement on guage

Drank beer and contemplated my mechanical skills

Hooligan

iceship · 07-08-2015, 10:06 AM

Love that steering wheel

**1971 GMC SHORTY** · 07-08-2015, 12:45 PM

Scored These Rare commercial Plates I Buddy has Had Them Hanging up For Years

**1971 GMC SHORTY** · 07-08-2015, 07:49 PM

Got The V8 Helping A Buddy Out

**1971 GMC SHORTY** · 07-08-2015, 07:53 PM

Quote:

Originally Posted by 1971 GMC SHORTY

Got The V8 Helping A Buddy Out

Here it is Love working on Stuff that PO 1/2 Assed Ever THING

jbgroby · 07-11-2015, 01:36 PM

Got the engine block to cab grounds mounted this morning. I have to remove the heater assembly to get to a hole. I must be getting better as I only smashed one finger.

LVPhotos · 07-11-2015, 02:17 PM

Making a mess! Pulled motor in hopes to attach and install transmission. Cleaning cab and firewall. Some touch up. Truck was originally Omaha orange but green primer? Keeps popping up on the lower cab.

OldChevy61 · 07-11-2015, 05:40 PM

Took the 12 bolt to the welding shop to get the new Captainfab mounting perches welded on and pan hard mount moved over.

scottco · 07-11-2015, 10:46 PM

Finished the disc brake 5 hole conversion. Cragar's are on and life is good !! lol

schpeen · 07-11-2015, 10:48 PM

Quote:

Originally Posted by scottco

Finished the disc brake 5 hole conversion. Cragar's are on and life is good !! lol

Keep wax on them. Looks perfect

LVPhotos · 07-11-2015, 10:50 PM

Quote:

Originally Posted by scottco

Finished the disc brake 5 hole conversion. Cragar's are on and life is good !! lol

Dig it! Like stockish stance. Hot Wheel red stripe tires would be cool.

LVPhotos · 07-12-2015, 06:22 PM

One step closer! McLeod hydraulic bearing installed because the 2466HKR Hooker Competition Headers don't work with stock arm and bellhouse. Had to clearance driver side bellhouse to clear.

mjh1965 · 07-12-2015, 06:34 PM

Well I went and removed and collected a new motor a 350 SBC for my truck today

jonzcustomshop · 07-13-2015, 02:13 AM

today I found the left front hubcap for my daily!
they are doing construction on a road I drive on to work, and it was extra rough yesterday. when I got to work I noticed the left front hubcap was missing

I drove home, scanning the route, but did not see it... but then today I drove even slower, and out of the corner of my eye noticed it next to a fence , laying upside down and full of rain water!!
so happy I don't have to bang out and paint up another one!

**Palf70Step** · 07-13-2015, 05:35 AM

LVPhotos · 07-13-2015, 05:11 PM

Back together! Short of one bolt on motor mount all went smoothly. The fab of the trans crossmember will be tomorrow. Still sitting on stands.

Lugnutz65 · 07-13-2015, 06:03 PM

Quote:

Originally Posted by LVPhotos

Back together! Short of one bolt on motor mount all went smoothly. The fab of the trans crossmember will be tomorrow. Still sitting on stands.

Nice work. So what setup do you have for the hydraulic clutch MC and pedal? Please include pics if you can.

schpeen · 07-13-2015, 06:08 PM

Finally got my steel smoothies to balance after trying 4 sets

LVPhotos · 07-13-2015, 07:39 PM

I used a Captainfab firewall bracket, CPP all in one master, Wilwood hydraulic clutch cylinder, McLeod hydraulic bearing. The chrome booster came from Tuckers Trucks either s10 or Nova base 7".
The 2466 HKR Hooker Compatition headers didn't work with arm and had to knock down driver side bellhouse to clear flange. This is why th hydraulic bearing over arm.
Stock pedal. Big feet can hit all 3 if you try!

Lugnutz65 · 07-13-2015, 10:28 PM

Quote:

Originally Posted by LVPhotos

I used a Captainfab firewall bracket, CPP all in one master, Wilwood hydraulic clutch cylinder, McLeod hydraulic bearing. The chrome booster came from Tuckers Trucks either s10 or Nova base 7".
The 2466 HKR Hooker Compatition headers didn't work with arm and had to knock down driver side bellhouse to clear flange. This is why th hydraulic bearing over arm.
Stock pedal. Big feet can hit all 3 if you try!

OK, you showed brake stuff too. Didn't need that but it's useful to other readers.

So the clutch MC is Wilwood. Model#? Mounting info? Heim joint and pushrod from the pedal connection?

LVPhotos · 07-13-2015, 11:00 PM

All the parts came with Captainfab kit. The firewall kit has a spot to drill for Wilwood and all hardware and rods came with kit.
http://www.67-72chevytrucks.com/vboa...d.php?t=362375

LVPhotos · 07-13-2015, 11:05 PM

Under dash... not mine.

07-07-2015, 09:16 PM	#1276
Pappyx3! Registered User Join Date: Feb 2014 Location: Stephens City, VA Posts: 326	Re: What did you do to your truck today part III Finally! Got the engine in on the 62. Planning to fire it up on Thursday evening. Attached Images __________________ 1962 Chevy C-10 Stepside 383 Stroker, Turbo 400 1966 Chevy C-10 Stepside 250 6Cyl, 3OTT- Daily Driver John 3:16

07-07-2015, 09:58 PM	#1278
Lugnutz65 Registered User Join Date: Jan 2013 Location: Columbia, SC Posts: 1,927	Re: What did you do to your truck today part III Repaired the pitted and rusted portion of the bed rear cross sill. Attached Images __________________ My 65 C10 build: www.lugnutz65chevystepside.weebly.com Want to know more about T5 transmissions? My website has a T5 Info Page and a Step by Step T5 rebuild.

07-08-2015, 09:44 AM	#1279
HappyHooligan Registered User Join Date: Apr 2015 Location: Welsh, LA Posts: 63	Re: What did you do to your truck today part III Replaced Speedo Driven gear, watched needle bounce around and then slowly down to nothing. Rebuilt Rag Joint on steering shaft..... twice. First try Steering wheel was upside down Replaced fuel sending unit Float. brass one was cracked. Checked ohms on sending unit and continuity to dash and ground. No movement on guage Drank beer and contemplated my mechanical skills Hooligan __________________ The Green Hornet 1960 Apache 10 Long Fleet - Driver and Work In Progress The Death Star 2006 Vstar 1100 - Chopped, Bobbed, Riding the Dark Side

07-08-2015, 10:06 AM	#1280
iceship Registered User Join Date: Apr 2011 Location: bowling green, ky Posts: 439	Re: What did you do to your truck today part III Love that steering wheel

07-08-2015, 12:45 PM	#1281
1971 GMC SHORTY Senior Member Join Date: Apr 2009 Location: SAN FERNANDO VALLE SOL CAL Posts: 1,064	Re: What did you do to your truck today part III Scored These Rare commercial Plates I Buddy has Had Them Hanging up For Years Attached Images __________________ 1966 GMC K25 V6 351E Original Utility Truck 2000 C3500 Hot Rod Utility Truck 2003 ROAD KING 100th 124ci 6 Speed 145CI M/P Pro Street FXR 2002 FXDP 2007 2500HD DURAMAX. DD Studio Teamsters / Mechanic Retired GM Master Tech 20 Years Retired Ford Tech 15 Years

07-08-2015, 07:49 PM	#1282
1971 GMC SHORTY Senior Member Join Date: Apr 2009 Location: SAN FERNANDO VALLE SOL CAL Posts: 1,064	Re: What did you do to your truck today part III Got The V8 Helping A Buddy Out Attached Images __________________ 1966 GMC K25 V6 351E Original Utility Truck 2000 C3500 Hot Rod Utility Truck 2003 ROAD KING 100th 124ci 6 Speed 145CI M/P Pro Street FXR 2002 FXDP 2007 2500HD DURAMAX. DD Studio Teamsters / Mechanic Retired GM Master Tech 20 Years Retired Ford Tech 15 Years

07-11-2015, 01:36 PM	#1284
jbgroby Registered User Join Date: Nov 2008 Location: Lacombe, LA Posts: 2,772	Re: What did you do to your truck today part III Got the engine block to cab grounds mounted this morning. I have to remove the heater assembly to get to a hole. I must be getting better as I only smashed one finger. Attached Images __________________ http://s1299.photobucket.com/user/jb...23904108567829

07-11-2015, 02:17 PM	#1285
LVPhotos Registered User Join Date: Jan 2013 Location: Las Vegas, NV Posts: 1,857	Re: What did you do to your truck today part III Making a mess! Pulled motor in hopes to attach and install transmission. Cleaning cab and firewall. Some touch up. Truck was originally Omaha orange but green primer? Keeps popping up on the lower cab. Attached Images __________________ 1962 shortbed 408cui small block, TKO 600 5-speed, bagged Porterbuilt suspension. 18" Salt Flats http://www.cardomain.com/ride/332579...t-c-k-pick-up/ http://67-72chevytrucks.com/vboard/s...d.php?t=560081

07-11-2015, 05:40 PM	#1286
OldChevy61 Registered User Join Date: Apr 2015 Location: NICHOLS SC Posts: 435	Re: What did you do to your truck today part III Took the 12 bolt to the welding shop to get the new Captainfab mounting perches welded on and pan hard mount moved over.

07-11-2015, 10:46 PM	#1287
scottco Registered User Join Date: Aug 2002 Location: Texas Posts: 198	Re: What did you do to your truck today part III Finished the disc brake 5 hole conversion. Cragar's are on and life is good !! lol Attached Images __________________ 1964 C10 SWB original 1970 SS El Camino 1964 Impala SS http://67-72chevytrucks.com/vboard/s...d.php?t=649951

07-12-2015, 06:22 PM	#1290
LVPhotos Registered User Join Date: Jan 2013 Location: Las Vegas, NV Posts: 1,857	Re: What did you do to your truck today part III One step closer! McLeod hydraulic bearing installed because the 2466HKR Hooker Competition Headers don't work with stock arm and bellhouse. Had to clearance driver side bellhouse to clear. Attached Images __________________ 1962 shortbed 408cui small block, TKO 600 5-speed, bagged Porterbuilt suspension. 18" Salt Flats http://www.cardomain.com/ride/332579...t-c-k-pick-up/ http://67-72chevytrucks.com/vboard/s...d.php?t=560081

07-12-2015, 06:34 PM	#1291
mjh1965 Registered User Join Date: Sep 2013 Location: Kent England Posts: 1,025	Re: What did you do to your truck today part III Well I went and removed and collected a new motor a 350 SBC for my truck today __________________ FINALLY PUTTING IT BACK TOGETHER AT LONG LAST MY BUILD THREAD: http://67-72chevytrucks.com/vboard/s...d.php?t=611614

07-13-2015, 02:13 AM	#1292
jonzcustomshop 1961 crewcab Join Date: Dec 2007 Location: missoula, mt Posts: 6,164	Re: What did you do to your truck today part III today I found the left front hubcap for my daily! they are doing construction on a road I drive on to work, and it was extra rough yesterday. when I got to work I noticed the left front hubcap was missing I drove home, scanning the route, but did not see it... but then today I drove even slower, and out of the corner of my eye noticed it next to a fence , laying upside down and full of rain water!! so happy I don't have to bang out and paint up another one! __________________ 60 build: http://67-72chevytrucks.com/vboard/s...d.php?t=280904 61 crew build: http://67-72chevytrucks.com/vboard/s...d.php?t=646830 63 build: http://67-72chevytrucks.com/vboard/s...d.php?t=336537 64 'burb build: http://67-72chevytrucks.com/vboard/s...d.php?t=448681 65 'burb build: http://67-72chevytrucks.com/vboard/s...d.php?t=590715 65 build: http://67-72chevytrucks.com/vboard/s...d.php?t=281955

07-13-2015, 05:35 AM	#1293
Palf70Step State of Confusion! Join Date: Jul 2002 Location: Gulfport, MS USA Posts: 47,082	Re: What did you do to your truck today part III __________________ Bill 1970 Chevy Custom/10 LWB Fleetside 2010 Toyota Tacoma PreRunner SR5 Double Cab - DD Member of Louisiana Classic Truck Club (LCTC) Bill's Gallery Life isn't tied with a bow, but it's still a gift. Live simply. Love generously. Care deeply. Speak kindly. Leave the rest to God!

07-13-2015, 05:11 PM	#1294
LVPhotos Registered User Join Date: Jan 2013 Location: Las Vegas, NV Posts: 1,857	Re: What did you do to your truck today part III Back together! Short of one bolt on motor mount all went smoothly. The fab of the trans crossmember will be tomorrow. Still sitting on stands. Attached Images __________________ 1962 shortbed 408cui small block, TKO 600 5-speed, bagged Porterbuilt suspension. 18" Salt Flats http://www.cardomain.com/ride/332579...t-c-k-pick-up/ http://67-72chevytrucks.com/vboard/s...d.php?t=560081



Register or Log In To remove these advertisements.

07-13-2015, 06:08 PM	#1296
schpeen Registered User Join Date: Jun 2014 Location: fort lauderdale, florida Posts: 511	Re: What did you do to your truck today part III Finally got my steel smoothies to balance after trying 4 sets

07-13-2015, 07:39 PM	#1297
LVPhotos Registered User Join Date: Jan 2013 Location: Las Vegas, NV Posts: 1,857	Re: What did you do to your truck today part III I used a Captainfab firewall bracket, CPP all in one master, Wilwood hydraulic clutch cylinder, McLeod hydraulic bearing. The chrome booster came from Tuckers Trucks either s10 or Nova base 7". The 2466 HKR Hooker Compatition headers didn't work with arm and had to knock down driver side bellhouse to clear flange. This is why th hydraulic bearing over arm. Stock pedal. Big feet can hit all 3 if you try! Attached Images __________________ 1962 shortbed 408cui small block, TKO 600 5-speed, bagged Porterbuilt suspension. 18" Salt Flats http://www.cardomain.com/ride/332579...t-c-k-pick-up/ http://67-72chevytrucks.com/vboard/s...d.php?t=560081 Last edited by LVPhotos; 07-13-2015 at 07:45 PM.

07-13-2015, 11:00 PM	#1299
LVPhotos Registered User Join Date: Jan 2013 Location: Las Vegas, NV Posts: 1,857	Re: What did you do to your truck today part III All the parts came with Captainfab kit. The firewall kit has a spot to drill for Wilwood and all hardware and rods came with kit. http://www.67-72chevytrucks.com/vboa...d.php?t=362375 __________________ 1962 shortbed 408cui small block, TKO 600 5-speed, bagged Porterbuilt suspension. 18" Salt Flats http://www.cardomain.com/ride/332579...t-c-k-pick-up/ http://67-72chevytrucks.com/vboard/s...d.php?t=560081

07-13-2015, 11:05 PM	#1300
LVPhotos Registered User Join Date: Jan 2013 Location: Las Vegas, NV Posts: 1,857	Re: What did you do to your truck today part III Under dash... not mine. __________________ 1962 shortbed 408cui small block, TKO 600 5-speed, bagged Porterbuilt suspension. 18" Salt Flats http://www.cardomain.com/ride/332579...t-c-k-pick-up/ http://67-72chevytrucks.com/vboard/s...d.php?t=560081

Register or Log In To remove these advertisements.