What did you do to your truck today.The 3rd chapter

[OregonNed]

close up

[KMC3420]

Finished making my patch panels for where the firewall and floor meet. Need to weld these in before pulling the old floor out.

Drivers side


Passenger side

[72c20customcamper]

My wife says I have a problem .

[KMC3420]

Originally Posted by 72c20customcamper

My wife says I have a problem .

A problem maybe, but I see you found a solution as well!

[FRCvette]

I installed my new chrome bumper from Cooper Restorations today.

[67C10Step]

72C20 - Yeah, but as my wife says: At least I don't have to go from bar to bar looking for you. I know right where you are when you disappear.

KMC3420 - I would like to know more about the patch panels. I need to do this exact same repair only my truck and was looking at it over the weekend trying to come up with a plan.

[Davidf]

Removed about 3/8" of body filler on the corner of my hood only to find poorly repaired previous damage. The bondo sculptor was not very good as the corner was way different than the other side. So, I opened her up to get some of the metal back to normal. Notice the single vertical cut and how far it opened up to get the metal close to where it belongs. Any suggestions on making a (compound curve) patch panel? A patch panel would sure come in handy if any has one available.

[BugzC10]

Finally got a spare and had the garage floor coated for her

[KQQL IT]

New key and tumbler for old blue.
The other key could come out and be turned off with anything and occasionally didn't need a key at all.

[72c20customcamper]

Did the drip rail today SEM self leveling seam sealer tried to get the truck as level as possible but it still puddled up in the front . Roof is now in high build primer plan is to paint the white this week

[KMC3420]

Originally Posted by 67C10Step

72C20 - Yeah, but as my wife says: At least I don't have to go from bar to bar looking for you. I know right where you are when you disappear.

KMC3420 - I would like to know more about the patch panels. I need to do this exact same repair only my truck and was looking at it over the weekend trying to come up with a plan.

I started out by cutting out the old to use as a template and then measured the template. From there I put my measurements on a flat piece of sheet metal. I use a bender I made for my shop press to bend up to 90 degrees. For cutting I use my right and left hand tin snips. Just take it nice and slow and sneak up on your final fitment.

Template


Template


Bender

[KMC3420]

Snips


Press

[Old_Gold]

Nice forming attachment for your press!

Jim

[3757chevy]

Originally Posted by Old_Gold

Nice forming attachment for your press!

Jim

[67C10Step]

KMC3420,
Nice, thanks for that information and the photos. I think I may have everything in my shop to build one of those breaks for my press except the black iron Tee. Like I need an excuse to go to the hardware store!

[KMC3420]

Thanks guys, it works pretty good for simply bending sheet metal, intended job. I often see attachments for a press (online), and gotta at least try to make the online $100 part for $10 worth of scrap metal and some welding wire.

[Boog]

If only the repro parts vendors would try something similar.

[KMC3420]

Originally Posted by Boog

If only the repro parts vendors would try something similar.

You got it! Wouldn't that be something, if successful they could dominate the market..

[A1971Blazer]

disassembled the power steering gear....
cleaned and painted the case.....
ready to re-assemble

[basketcase]

Originally Posted by Davidf

Removed about 3/8" of body filler on the corner of my hood only to find poorly repaired previous damage. The bondo sculptor was not very good as the corner was way different than the other side. So, I opened her up to get some of the metal back to normal. Notice the single vertical cut and how far it opened up to get the metal close to where it belongs. Any suggestions on making a (compound curve) patch panel? A patch panel would sure come in handy if any has one available.

I would make 3 maybe 4 small pieces which would be easier than trying to do that complicated form all in one piece. Tack them together and work with them until you are close enough to hammer and dolly and get by with just a skim coat of filler. Make cardboard templates from the good side for a guide.


Tom

[ohboy321]

Put the first coat of black paint on the steering wheel I'm restoring. This is my first attempt at making a part as smooth as possible before paint is applied and so far it is coming out pretty good.

[72c20customcamper]

Painted the firewall this am . Going away for the weekend but I plan on painting ths roof monday . Going with 562 off white eventhough it's not original to the truck .

Should start taking pictures with my good camera . Phone sucks

[jimijam00]

Drove it across the state for the long holiday weekend. 250 miles in the 90+ degree heat, 75 mph air conditioning, and had to stop for gas twice. That's leaving home with a full tank too. So two tanks, and then a little more to get me the 250 miles.

[fourspeedwagon]

It’s time to put the engine in my ‘71. I pulled the driveshaft and greased the Ujoints, painted the inner fenders, core support, hood hinges, etc.
Got the engine and trans lowered into place and bolted up. Got all the exhaust bolts wire brushed and found the half moon tangs the go on the exhaust bolts and cleaned them up too. New exhaust manifold gaskets, I spaced getting new heater hose so I need to go grab that. I’m sure I’ll find some more things missing but hoping to hook the wires all up and light the fire on Saturday.
It’ll be fun- I got the truck with no engine so I’ve not driven it yet.

[fourspeedwagon]

In the daylight it looks like it could use a shampooing- but still well worth the price paid!


Edit- oops, put this in the wrong thread. Anyway, this is a freebie seat I got last night.