OR Parting out 72 Suburban C10 402 TH400

[tll74]

Originally Posted by Gary 70 Jimmy

I will take it if it looks good after you acid dip it.

It is off and will go in dip tank tonight.

Originally Posted by Pmarti69

Do you still have the 71-72 gas pedal assy with TH400 switch and wiring to engine harness. If so can you post a picture of it. Thanks again, I was able to find TH400 locally. Thanks Paul

Same reply as the seat belt tread. Pic to come when I get home.

Originally Posted by restart42

post 12 shows headliner bows, do you have the
three bows with the clips ?
shipped to 10462 ?

Thanks,,,Pat

Pat, 23.00 shipping

Thanks, Tom

[tll74]

Originally Posted by notsolo

Hey Tom I could use rt side door hinges for 72 blazer and left window regulator. (Hoping its the same as what you have) inside door handles and winder handles both sides. Cost with shipping to 21863 .... Thanks... Ed

Ed, nice original hinges dipped (I have tons of these) and ready for paint 35.00, 72 only RH window reg. good rollers 25.00, 8.00 for all four inner handles. I'll pick out the best four out of my stash. Shipping 14.00 Thanks, Tom

[tll74]

pic of the gas pedal.

[restart42]

Originally Posted by tll74

.
Pat, 23.00 shipping

Thanks, Tom

Before you pack'em up, do you have the screw on clamp that
holds the spare tire in the 67-72 Suburbans ? (sort of looks like a bow tie)
If so PM me total for all ,including shipping.

Thanks ,,Pat

[notsolo]

Originally Posted by tll74

Ed, nice original hinges dipped (I have tons of these) and ready for paint 35.00, 72 only RH window reg. good rollers 25.00, 8.00 for all four inner handles. I'll pick out the best four out of my stash. Shipping 14.00 Thanks, Tom

Thanks Tom... Payment sent,Looking forward to ready to paint parts...Ed

[tll74]

Originally Posted by restart42

Before you pack'em up, do you have the screw on clamp that
holds the spare tire in the 67-72 Suburbans ? (sort of looks like a bow tie)
If so PM me total for all ,including shipping.

Thanks ,,Pat

Pat, look at post #15 4th pic down in the center towards the top. I believe this is what your after. That one is sold but I have one in the 72 white C10 which is next to take apart. I sell the wing nut/stud and plate together for 20.00. PM sent

[restart42]

Originally Posted by tll74

Pat, look at post #15 4th pic down in the center towards the top. I believe this is what your after. That one is sold but I have one in the 72 white C10 which is next to take apart. I sell the wing nut/stud and plate together for 20.00. PM sent

Yep,,that's it,, will PM the PayPal total $73

Thanks again,,,Pat

[LockDoc]

-
Hey Tom, any chance you could take pictures of the Parchment front seat belt set laid out flat? How bad are they stained?

Thanks.
LockDoc

[tll74]

Originally Posted by LockDoc

-
Hey Tom, any chance you could take pictures of the Parchment front seat belt set laid out flat? How bad are they stained?

Thanks.
LockDoc

Will do. Oh yea I'll get a update of the key blanks I need. Kinda forgot.
Thanks, Tom

[tll74]

Originally Posted by Gary 70 Jimmy

I will take it if it looks good after you acid dip it.

Gary, pics of the heat stove. If you hold it up in the light you can see some pin holes. Pic four, the extension on the LH on the LH edge as a small spot that is rusted away. Over all if this was to be sealed up and painted it would display nicely. LMK
Thanks, Tom

[LockDoc]

Originally Posted by tll74

Will do. Oh yea I'll get a update of the key blanks I need. Kinda forgot.
Thanks, Tom

Sounds good. Thanks.

LockDoc

[DINS 1]

do you still have the body around looking for a upper rear door panel as marked price with shipping. the body part not the liftgate

[haskell]

I will take the cover plates for the rear doors if still available. Will take the wing nut and retainer for spare if still available.

Also do you have the splash shield that mounts behind the driver side rear tire? Condition and price if you do please.

Shipping would be to 46240

[1lo67]

Here's a pic of the section i'm needing from both sides. just let me know what you come up with....37860
Thanks

[wrwelton]

Iam looking for the legs and tracks for a bench seat. I have a seat but no hardware underneath

[tll74]

Seat belt pics. There is some stains in the center belts they are hard to see in the pics. The male buckles have some rust as the pics shows and the female halfs have some discoloration. The outer plastic covers are nice and one retractor is a bit lazy.

[tll74]

more belt pics

[tll74]

Originally Posted by DINS 1

do you still have the body around looking for a upper rear door panel as marked price with shipping. the body part not the liftgate

I have this cut off another 72 that I just drug home last night. How far forward from the drip rail and how far down the post?

Originally Posted by haskell

I will take the cover plates for the rear doors if still available. Will take the wing nut and retainer for spare if still available.

Also do you have the splash shield that mounts behind the driver side rear tire? Condition and price if you do please.

Shipping would be to 46240

The spare parts are sold. I have all the covers still and also have the splash shield. 25.00 on the shield. 35.00 if I hot tank and acid dip it. Shipping on all of it would run about 15.00

Originally Posted by 1lo67

Here's a pic of the section i'm needing from both sides. just let me know what you come up with....37860
Thanks

That's what I thought from your description. I'm thinking 225.00 for the cuts plus shipping. If interested I can get a shipping cost.

Originally Posted by wrwelton

Iam looking for the legs and tracks for a bench seat. I have a seat but no hardware underneath

40.00 for the seat tracks complete. plus shipping

Thanks to all, Tom

[LockDoc]

Originally Posted by tll74

more belt pics

I will take the Parchment seat belts and body plugs in the other thread if you want to do some trading on the key blanks and door lock gaskets you want.

PM sent.

LockDoc

[DINS 1]

Is the one you have cut off from a lift gate truck? I would need The roof cur behind the rear door frame and down the post about 4 inches in to the side window. cuts would be in green. price and shipping to 50595

[tll74]

Originally Posted by LockDoc

I will take the Parchment seat belts and body plugs in the other thread if you want to do some trading on the key blanks and door lock gaskets you want.

PM sent.

LockDoc

Sure, that sounds fine. I'll answer your PM in a bit.

Originally Posted by DINS 1

Is the one you have cut off from a lift gate truck? I would need The roof cur behind the rear door frame and down the post about 4 inches in to the side window. cuts would be in green. price and shipping to 50595

I don't have this cut already cut off. I do have it on a complete 72 that I have not touched yet. It is a lift gate truck. 125.00 on the cut. I will have to measure it up and get a shipping cost in the morning.

Thanks, Tom

[haskell]

I will take the cover plates for the rear doors if still available. Will take the wing nut and retainer for spare if still available.

Also do you have the splash shield that mounts behind the driver side rear tire? Condition and price if you do please.

Shipping would be to 46240
The spare parts are sold. I have all the covers still and also have the splash shield. 25.00 on the shield. 35.00 if I hot tank and acid dip it. Shipping on all of it would run about 15.00

I will take the covers and splash shield. Go ahead an hot tank and dip. Shipping to 46240. Please pm payment details. Do you just want $15 for shipping or will that be priced when packed?

Tim

[tll74]

Tim, It will take a few days for the process of the splash shield. 15.00 will work fine for shipping. I'll PM the payment info. Thanks, Tom

[tll74]

Pics for budnikguy

[DINS 1]

i will pass on the upper door cut found one locally