My build thread.. 63 LS powered C10 - Page 6 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

noonzor · 03-31-2012, 01:16 PM

what kind of numbers are you hoping for from the new 418? i know a 12 bolt can be built up to handle high hp, just the 9" seems to be the more trusted route. not that im questioning your methods, just curious.

Super73 · 03-31-2012, 07:50 PM

Hoping to go 10.7x-10.8x on motor next time out and get it down to 10.5x in the near future. On the unit, hoping to go 9.9x and work it down to at least a 9.5x. For all I know, the rear could last 10 years or 1 pass. I don't look forward to having to build the 9", but when the 12 bolt goes, the 9" will get built. Maybe before.

*Vortecpro* · 03-31-2012, 10:46 PM

Quote:

Originally Posted by Super73

Hoping to go 10.7x-10.8x on motor next time out and get it down to 10.5x in the near future. On the unit, hoping to go 9.9x and work it down to at least a 9.5x. For all I know, the rear could last 10 years or 1 pass. I don't look forward to having to build the 9", but when the 12 bolt goes, the 9" will get built. Maybe before.

Ck out the rear end 69 GMC 910 had built.

djracer · 04-01-2012, 08:28 AM

That Tig Welding is so Sexy!

Super73 · 04-08-2012, 11:31 PM

Ok, went by again to see the truck late last week. Had another set of headers to try and fit. Let's just say they did not work with the new 6 bolt heads

But here are some pics of the wishbone.

Super73 · 04-08-2012, 11:33 PM

I was uploading the above pics when I got a plesant suprise via text I believe this means all the welding on the chassis is done. Well, minus the bottle brackers, Mounting the cell and the fuel pump.. Oh, and removing the existing cross member that held the LCA's in place and putting in a new cross member with driveshaft loop.

LSPWRD67CHEVY · 04-09-2012, 08:11 AM

How are you going to do the bed? just curious..

Super73 · 04-09-2012, 09:31 AM

Unbolt the front panel, put it in place and bolt the panel back in. The 60-66 beds can be completely unbolted.

LSPWRD67CHEVY · 04-09-2012, 09:41 AM

Quote:

Originally Posted by Super73

Unbolt the front panel, put it in place and bolt the panel back in. The 60-66 beds can be completely unbolted.

Right. I should have been more clear. I was wondering more about the inside, like are you going to put tubs in it or a floor or a bed cover, stuff like that?

Super73 · 04-09-2012, 12:17 PM

Thinking of doing an alum bed cover. I don't run a gate most the time, if I do it is down. I have also thought about skinning the bottom of the truck, similar to how the newer betts are done.
Posted via Mobile Device

djracer · 04-09-2012, 10:28 PM

I have thought about running a wishbone with trailing arms.

**Captainfab** · 04-10-2012, 12:02 AM

That's interesting. I'm used to seeing the wishbone above the axle.

Truck is looking very nice.

noonzor · 04-10-2012, 12:34 AM

so very very sweet. gettin close man you must be happy, id be ear to ear grinnin with that craftsmanship!

Super73 · 04-16-2012, 12:48 AM

Joe cut the front panel today and we set the bed on the frame. Notice we left two holes per side. It helped keep it from being floppy with the little bit of shear strength in the sheet metal (upper aera you can see a slight triangle).

Super73 · 04-16-2012, 12:51 AM

Couple more from today.

Super73 · 04-24-2012, 09:15 PM

Joe sent me these couple pics today. We discussed lowering the truck a little more in the rear. It is now about 2" lower.

He also mounted the N20 bottle.

Got a bunch of stuff in the mail today from Summit. I am making some changes to the fuel system to run E85. Fuel system will look like this:

5/8 (-10) hard line from cell to Weldon 2035-A
Splitting to dual 1/2 (-8) before the rails
Off the other end of the rails is a -4 T fitting
One 1/4 (-4) goes to the N20 noids (one on each side, 2-stage) the other goes to the Aeromotive A1000 regulator
1/2 (-8) return back to the cell

Things left for Joe to do before I get it back and start working on the fuels system:

Mount the batterey
Mount the fuel cell
Drain plug in radiator
Rod end radiator mounts from the front bars cage bars to the radiator
Map out 4-link for ICG

I have a race coming up May 19/20 that I am hoping to be running by.

bigboybodry · 04-24-2012, 10:16 PM

Looking good brother mines next
Posted via Mobile Device

team39763 · 05-01-2012, 03:17 PM

Your truck is getting serious man. Come a long way since I first seen it a few years ago.

Super73 · 05-01-2012, 10:27 PM

Yup, it's a money pit.. Good news is it is coming home on Friday. Then on to getting the fuel system back together and a rear brake line. Should hopefully be racing the 19th and 20th. Just 1/8 mile with no track prep or timers, but will give me some seat time

1Bad62Pro/Street · 05-01-2012, 10:43 PM

Shakedown run
What do you think your 60ft time will be with all the new goodies on her now?
Maybe you can have someone to video you launching out of the hole and down the track to see the difference now.

Super73 · 05-05-2012, 11:36 PM

It is home....
Posted via Mobile Device

68 C-10 KID · 05-06-2012, 12:28 PM

Super congrats on your progress. Looks like a jr promod tuck in the making. Only thing I see missing is your wheelie bars.lol Best of luck at the track in a few weeks. Wheels up and have some fun. Keep us posted.
Posted via Mobile Device

Marv D · 05-06-2012, 02:22 PM

no other word comes to mind.. just "WOW"!!!

dbmx66 · 05-06-2012, 04:12 PM

truck is looking nice, lots a great fabrication work for sure

bigboybodry · 05-07-2012, 07:22 AM

Awesome!!! sums it up in a nut shell
Posted via Mobile Device

03-31-2012, 01:16 PM	#126
noonzor Registered User Join Date: Aug 2009 Location: Edmonton, Alberta Posts: 818	Re: My build thread.. 63 LS powered C10 what kind of numbers are you hoping for from the new 418? i know a 12 bolt can be built up to handle high hp, just the 9" seems to be the more trusted route. not that im questioning your methods, just curious. __________________ 69 c10 Shortbox Build http://67-72chevytrucks.com/vboard/s...d.php?t=360622

03-31-2012, 07:50 PM	#127
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: My build thread.. 63 LS powered C10 Hoping to go 10.7x-10.8x on motor next time out and get it down to 10.5x in the near future. On the unit, hoping to go 9.9x and work it down to at least a 9.5x. For all I know, the rear could last 10 years or 1 pass. I don't look forward to having to build the 9", but when the 12 bolt goes, the 9" will get built. Maybe before. __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49

04-01-2012, 08:28 AM	#129
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,891	Re: My build thread.. 63 LS powered C10 That Tig Welding is so Sexy! __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

04-08-2012, 11:31 PM	#130
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: My build thread.. 63 LS powered C10 Ok, went by again to see the truck late last week. Had another set of headers to try and fit. Let's just say they did not work with the new 6 bolt heads But here are some pics of the wishbone. Attached Images __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49

04-08-2012, 11:33 PM	#131
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: My build thread.. 63 LS powered C10 I was uploading the above pics when I got a plesant suprise via text I believe this means all the welding on the chassis is done. Well, minus the bottle brackers, Mounting the cell and the fuel pump.. Oh, and removing the existing cross member that held the LCA's in place and putting in a new cross member with driveshaft loop. Attached Images __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49

04-09-2012, 08:11 AM	#132
LSPWRD67CHEVY Registered User Join Date: Aug 2009 Location: Shawnee, OK Posts: 106	Re: My build thread.. 63 LS powered C10 How are you going to do the bed? just curious.. __________________ 1967 C-10 (project) 1964 Pontiac Lemans (Treasure lol) 2009 GMC Denali Truck (DD)

04-09-2012, 09:31 AM	#133
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: My build thread.. 63 LS powered C10 Unbolt the front panel, put it in place and bolt the panel back in. The 60-66 beds can be completely unbolted. __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49

04-09-2012, 12:17 PM	#135
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: My build thread.. 63 LS powered C10 Thinking of doing an alum bed cover. I don't run a gate most the time, if I do it is down. I have also thought about skinning the bottom of the truck, similar to how the newer betts are done. Posted via Mobile Device __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49

04-09-2012, 10:28 PM	#136
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,891	Re: My build thread.. 63 LS powered C10 I have thought about running a wishbone with trailing arms. __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

04-10-2012, 12:02 AM	#137
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,251	Re: My build thread.. 63 LS powered C10 That's interesting. I'm used to seeing the wishbone above the axle. Truck is looking very nice. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

04-10-2012, 12:34 AM	#138
noonzor Registered User Join Date: Aug 2009 Location: Edmonton, Alberta Posts: 818	Re: My build thread.. 63 LS powered C10 so very very sweet. gettin close man you must be happy, id be ear to ear grinnin with that craftsmanship! __________________ 69 c10 Shortbox Build http://67-72chevytrucks.com/vboard/s...d.php?t=360622

04-16-2012, 12:48 AM	#139
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: My build thread.. 63 LS powered C10 Joe cut the front panel today and we set the bed on the frame. Notice we left two holes per side. It helped keep it from being floppy with the little bit of shear strength in the sheet metal (upper aera you can see a slight triangle). Attached Images __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49 Last edited by Super73; 04-16-2012 at 12:54 AM.

04-16-2012, 12:51 AM	#140
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: My build thread.. 63 LS powered C10 Couple more from today. Attached Images __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49

04-24-2012, 09:15 PM	#141
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: My build thread.. 63 LS powered C10 Joe sent me these couple pics today. We discussed lowering the truck a little more in the rear. It is now about 2" lower. He also mounted the N20 bottle. Got a bunch of stuff in the mail today from Summit. I am making some changes to the fuel system to run E85. Fuel system will look like this: 5/8 (-10) hard line from cell to Weldon 2035-A Splitting to dual 1/2 (-8) before the rails Off the other end of the rails is a -4 T fitting One 1/4 (-4) goes to the N20 noids (one on each side, 2-stage) the other goes to the Aeromotive A1000 regulator 1/2 (-8) return back to the cell Things left for Joe to do before I get it back and start working on the fuels system: Mount the batterey Mount the fuel cell Drain plug in radiator Rod end radiator mounts from the front bars cage bars to the radiator Map out 4-link for ICG I have a race coming up May 19/20 that I am hoping to be running by. Attached Images __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49

04-24-2012, 10:16 PM	#142
bigboybodry Registered User Join Date: Jul 2009 Location: Florence,Mississippi Posts: 301	Re: My build thread.. 63 LS powered C10 Looking good brother mines next Posted via Mobile Device __________________ first track pass with the new motor on motor http://youtu.be/YgrJaEF_TaQ



Register or Log In To remove these advertisements.

05-01-2012, 03:17 PM	#143
team39763 Registered User Join Date: Feb 2007 Location: Texas Posts: 469	Re: My build thread.. 63 LS powered C10 Your truck is getting serious man. Come a long way since I first seen it a few years ago. __________________ 1982 Silverado - SBE, cleaned up GM heads, small cam, TH350, 850 Demon, 4.56 gears, and caltracs. Best time so far 11.8@XXXMPH

05-01-2012, 10:27 PM	#144
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: My build thread.. 63 LS powered C10 Yup, it's a money pit.. Good news is it is coming home on Friday. Then on to getting the fuel system back together and a rear brake line. Should hopefully be racing the 19th and 20th. Just 1/8 mile with no track prep or timers, but will give me some seat time __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49

05-01-2012, 10:43 PM	#145
1Bad62Pro/Street "Where were you in '62?" Join Date: Jul 2004 Location: Cleveland County, North Cackalacky Posts: 5,013	Re: My build thread.. 63 LS powered C10 Shakedown run What do you think your 60ft time will be with all the new goodies on her now? Maybe you can have someone to video you launching out of the hole and down the track to see the difference now. __________________ PROJECT: "FULL METAL YELLOW JACKET" 1962 Chevy C-10 Stepside Shortbed Nostalgia Pro/Street Pickup Truck PROJECT: "FULL METAL YELLOW JACKET Build Thread What Are You Workin' On? - 1Bad62ChevyPickup PROJECT: "TYRANNORAMBLER REX" 1969 AMC Rambler American Nostalgia Pro/Street Youtube Channel: Father Son Projects Youtube Channel: 2TIMOTHY2FITHTEEN "North and South Carolina Folks Click Here!" (((( ~ I have Parts For Sale & Miscellaneous Stuff ~ )))) "Well being as there's no other place around the place, I reckon this must be the place, I reckon...Nyuk Nyuk Nyuk" -Curly Howard Ph.D.

05-05-2012, 11:36 PM	#146
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: My build thread.. 63 LS powered C10 It is home.... Posted via Mobile Device __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49

05-06-2012, 12:28 PM	#147
68 C-10 KID Mean Green Join Date: Sep 2007 Location: Portland, OR Posts: 522	Re: My build thread.. 63 LS powered C10 Super congrats on your progress. Looks like a jr promod tuck in the making. Only thing I see missing is your wheelie bars.lol Best of luck at the track in a few weeks. Wheels up and have some fun. Keep us posted. Posted via Mobile Device __________________ 427 SBC 683HP & 590ftlbsTRQ @ fly wheel. 60'-1.38 1/4-10.43 MPH-124.6 New ET current 4/2019 AKA MEAN GREEN.

05-06-2012, 02:22 PM	#148
Marv D Registered Truck Offender Join Date: May 2008 Location: hells training ground (aka Ariz) Posts: 3,118	Re: My build thread.. 63 LS powered C10 no other word comes to mind.. just "WOW"!!! __________________ Still playin with trucks, even at my age! When you're dead, it's only a problem for the people around you, because you don't know you're dead. .....It's kinda the same when your STUPID. I just did my taxes and reviewed my SS statement. Thanks to the current administration it looks like I will only have to work till noon on the day of my funeral.

05-06-2012, 04:12 PM	#149
dbmx66 Registered User Join Date: Aug 2009 Location: PA Posts: 883	Re: My build thread.. 63 LS powered C10 truck is looking nice, lots a great fabrication work for sure

05-07-2012, 07:22 AM	#150
bigboybodry Registered User Join Date: Jul 2009 Location: Florence,Mississippi Posts: 301	Re: My build thread.. 63 LS powered C10 Awesome!!! sums it up in a nut shell Posted via Mobile Device __________________ first track pass with the new motor on motor http://youtu.be/YgrJaEF_TaQ

Register or Log In To remove these advertisements.