|
06-03-2015, 07:48 PM | #1 |
Registered User
Join Date: Nov 2013
Location: Henderson, NV
Posts: 306
|
Re: My 63 Project
And a view of both sides.
|
09-05-2015, 01:33 AM | #2 |
Registered User
Join Date: Apr 2012
Location: Vegas
Posts: 617
|
Re: My 63 Project
Bad ass build so far, nice attention to detail!
|
09-08-2015, 02:10 PM | #3 |
Registered User
Join Date: Dec 2014
Location: peoria, il
Posts: 112
|
Re: My 63 Project
Great Build! Just read the whole thing! How much clearance do you have on the bottom side of the driveshaft with the flipped crossmember?
|
09-08-2015, 02:23 PM | #4 | |
Registered User
Join Date: Nov 2013
Location: Henderson, NV
Posts: 306
|
Re: My 63 Project
Quote:
Looks to be about an inch and a half. |
|
10-29-2017, 04:50 PM | #5 |
Registered User
Join Date: Apr 2011
Location: .
Posts: 3,104
|
Re: My 63 Project
Thank you for the heads up.
Have had similar dealings with other retailers and it really Kills ones motivation. |
11-13-2019, 09:33 PM | #6 |
Registered User
Join Date: Nov 2013
Location: Henderson, NV
Posts: 306
|
Re: My 63 Project
So having a side fill gas tank.. And I have since replaced this tank as it developed rust holes in less than 4 years. Anyway.. this was my answer to where to install the gas filler....
|
11-13-2019, 10:30 PM | #7 |
Registered User
Join Date: Nov 2013
Location: Henderson, NV
Posts: 306
|
Rusted Tank
So this is the original Red tank that I purchased, painted and installed. While I was installing my SNIPER EFI system, I was installing the new fuel pump when I noticed the blisters in the paint on the bottom of the tank. When I rubbed one of the blisters... GUSHER!!!! And I had just put 15 gallons of 91 octane in the tank.....
Last edited by ZouchaR; 11-14-2019 at 01:28 PM. Reason: It contained nothing... |
11-14-2019, 01:32 PM | #8 |
Registered User
Join Date: Nov 2013
Location: Henderson, NV
Posts: 306
|
Re: My 63 Project
Because I SUCK at tuning carburetors and because I couldn’t really find the right combination for this motor.... I purchased the Holley Sniper EFI system.....
This system is AMAZING!!!! a single O2 sensor... high pressure fuel pump... return line too the tank... couple of wires.... VROOM!!!!! Last edited by ZouchaR; 11-16-2019 at 02:53 AM. |
11-14-2019, 01:42 PM | #9 |
Registered User
Join Date: Nov 2013
Location: Henderson, NV
Posts: 306
|
Re: My 63 Project
This is the video of the first key turn start with the new Sniper EFI... Listen too the motor rev up.. and then immediately slow down too the idle RPM that we set with the handheld unit....
https://youtu.be/IGj-6-vG2eI |
11-15-2019, 03:42 PM | #10 |
Senior Member
Join Date: Aug 2017
Location: Louisville, KY
Posts: 376
|
Re: My 63 Project
Sounding good. I've considered Sniper or going LS for a while.
|
08-12-2020, 11:34 AM | #11 |
Registered User
Join Date: Mar 2015
Location: Washington State
Posts: 1,644
|
Re: My 63 Project
Good Write up, it is a bit older but still a good write up.
Thanks |
08-12-2020, 11:45 AM | #12 |
Registered User
Join Date: Jun 2014
Location: Paul idaho
Posts: 263
|
Re: My 63 Project
Truck looks great man! Good work
__________________
63 C10 |
Bookmarks |
|
|