What did you do to your truck today? Chapter II - Page 6 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Mike_The_Grad** · 01-31-2014, 12:20 PM

This was 2 days ago. My first successful engine/trans pull. Had a couple buddies with a lot more experience than me, over to help. And I'm very glad they showed up. Saved me from making a very time consuming mistake since I was going to just yank the distributor out without finding tdc on #1 piston! Now begins the fun part! CLEANING! then paint. Also found out my timing chain cover is missing my degree timer. So now I gotta pull balancer and water pump.just one more thing to do... but it needs to be done. Might as well do it while its out in the open. I'm really excited to see how this is all gonna turn out. More pics soon to come

VWNate1 · 01-31-2014, 03:11 PM

Grimy but not really bad , it'll look great when you're finished .

Did you remove the entire front clip as one piece ? .

texjake · 01-31-2014, 09:16 PM

My Flowmasters came in today & got them installed. It sounds so much better now! And yes my interior is still gutted, waiting on parts to come in.

BugzC10 · 01-31-2014, 09:54 PM

Quote:

Originally Posted by texjake

My Flowmasters came in today & got them installed. It sounds so much better now! And yes my interior is still gutted, waiting on parts to come in.

Which one did you get and how bout a sound clip / video.

ole dollor · 01-31-2014, 09:58 PM

Quote:

Originally Posted by texjake

My Flowmasters came in today & got them installed. It sounds so much better now! And yes my interior is still gutted, waiting on parts to come in.

need to drop by and see what you have done so far.....how far away are you from street use ... ole dollor is at the trans shop fixing a small drip right now...took her today and will try and pick her up on Monday..

texjake · 02-01-2014, 02:02 AM

Quote:

Originally Posted by BugzC10

Which one did you get and how bout a sound clip / video.

I got the 40 series & its not as loud as I thought it was going to be. I don't know if it's because I've got a long bed & the fact I'm running them all the way out back & didn't center dump them. I just know they sound better than the Flo-Pro's the PO had installed on the truck. And I don't get any drone in the cab either. In fact I can't really hear them until I step out of the cab & walk back towards the rear of the truck. I'll try to get a sound/video clip tomorrow.

texjake · 02-01-2014, 02:22 AM

Quote:

Originally Posted by ole dollor

need to drop by and see what you have done so far.....how far away are you from street use ... ole dollor is at the trans shop fixing a small drip right now...took her today and will try and pick her up on Monday..

Hey, Ole, I'm still far away from being street ready, since the weather wont co-operate & Ive got my dash & interior gutted out & still waiting on interior parts. I took a big chance today and drove it across town to the muffler shop get my Flowmasters installed. And the weather doesn't look to be any better next week either, I'll sure be glad when Spring gets here.

BugzC10 · 02-01-2014, 08:47 AM

Quote:

Originally Posted by texjake

I got the 40 series & its not as loud as I thought it was going to be. I don't know if it's because I've got a long bed & the fact I'm running them all the way out back & didn't center dump them. I just know they sound better than the Flo-Pro's the PO had installed on the truck. And I don't get any drone in the cab either. In fact I can't really hear them until I step out of the cab & walk back towards the rear of the truck. I'll try to get a sound/video clip tomorrow.

Running them out the back is exactly why they don't sound as loud as dumping them under the bed/axle. I have the 40s dumped under bed. Love the cam sound with the dual exhaust at idle, but wonder if it is going to be annoying while cruising. (haven't driven er much)
Sounds like you might mis that rumble under the truck...

tomshortwide69 · 02-01-2014, 12:49 PM

texjake · 02-01-2014, 03:32 PM

Quote:

Originally Posted by BugzC10

Running them out the back is exactly why they don't sound as loud as dumping them under the bed/axle. I have the 40s dumped under bed. Love the cam sound with the dual exhaust at idle, but wonder if it is going to be annoying while cruising. (haven't driven er much)
Sounds like you might mis that rumble under the truck...

I am sure it will get louder the more I drive it. I'm not sure I'll miss the done or rumble. I plan on taking it on some long road trips & don't want to be droned out by the time I get to my destination. Out here where I live it's a good 45 miles between towns & nothing much in between. So that's a long trip of being constantly droned out on the highway.

Lou Boffa · 02-01-2014, 05:55 PM

couldn't help it. I'm a sucker for truck bling. Installed core support filler plates.

ole dollor · 02-01-2014, 06:38 PM

Quote:

Originally Posted by Lou Boffa

couldn't help it. I'm a sucker for truck bling. Installed core support filler plates.

your bling looks really good...I like it. nice truck also.

Econman · 02-01-2014, 06:54 PM

Haven't worked on it today. The rolling chassis is completed (rebuilt rears, new suspension, all grade 8 stainless hardware, stainless brake lines, stainless fuel lines, everything powder coated including rally wheels.

Engine block, crank, rods/pistons and heads all in the machine shop. Just waiting to get them back to start building the engine back...

I discovered a '72 Super C20 today. Was sold to a recycling center for scrap metal. Complete truck. Quite a bit of rust, but otherwise pretty straight. Camper Special with dual tanks. I'm hoping to buy the door panels out of it - they're in nice condition with wood grain inserts. If it isn't bought soon, I guess it will be crushed. It's been parked adjacent to the crusher awaiting a possible buyer for several months.

Lou Boffa · 02-01-2014, 07:25 PM

Quote:

Originally Posted by ole dollor

your bling looks really good...I like it. nice truck also.

Thanks Dollar. Long steppers rock.

Lanman1972 · 02-01-2014, 08:29 PM

I made a sign to light up the Truck's side of the garage. Laser cut 1/8" aluminum plate, translucent acrylic, with LED backlight. Orange/White/Orange to match the truck.

ole dollor · 02-01-2014, 08:56 PM

Quote:

Originally Posted by Lanman1972

I made a sign to light up the Truck's side of the garage. Laser cut 1/8" aluminum plate, translucent acrylic, with LED backlight. Orange/White/Orange to match the truck.

now that's a cool sign...like it

texjake · 02-01-2014, 10:04 PM

Quote:

Originally Posted by BugzC10

Which one did you get and how bout a sound clip / video.

Here is a video clip. The clip may not be very loud, it's iPhone video quality if you know what I mean. I know it's not super loud but sure sounds a heck of a lot better than what the PO had on there. https://www.youtube.com/watch?v=t8QrWmi9pps

magwakeenercew2jh · 02-01-2014, 10:49 PM

Quote:

Originally Posted by texjake

Here is a video clip. The clip may not be very loud, it's iPhone video quality if you know what I mean. I know it's not super loud but sure sounds a heck of a lot better than what the PO had on there. https://www.youtube.com/watch?v=t8QrWmi9pps

Your sound is amazingly consistent with the 300hp 350, 2.5" pipes into two 40 series Flowmasters that made this sound on the last truck of mine (a '72).

https://www.youtube.com/watch?v=OxRy_sAmJYo

Just because...long story...I'm running 2.25 inch pipes thru the same series Flowmaster mufflers (also all the way out the back) on the current
build, RAT. I don't have a sound clip, but the 350 in RAT is way less cammed up. It makes far less noise. To me, that's unfortunate.

I did use an extremely heavy dose of sound deadener in RAT. So, we'll see what happens to the sound inside the cab with the 2.25" pipes after
the motor work.

texjake · 02-01-2014, 10:56 PM

Quote:

Originally Posted by magwakeenercew2jh

Your sound is amazingly consistent with the 300hp 350, 2.5" pipes into two 40 series Flowmasters that made this sound on the last truck of mine (a '72).

https://www.youtube.com/watch?v=OxRy_sAmJYo

Just because...long story...I'm running 2.25 inch pipes thru the same series Flowmaster mufflers (also all the way out the back) on the current
build, RAT. I don't have a sound clip, but the 350 in RAT is way less cammed up. It makes far less noise. To me, that's unfortunate.

I did use an extremely heavy dose of sound deadener in RAT. So, we'll see what happens to the sound inside the cab with the 2.25" pipes after
the motor work.

The link to your video is set to private and I cannot play it.

magwakeenercew2jh · 02-01-2014, 11:01 PM

Quote:

Originally Posted by texjake

The link to your video is set to private and I cannot play it.

Thanks. Should be fixed now......Sorry.

88fordf150 · 02-02-2014, 12:04 PM

Quote:

Originally Posted by Lanman1972

I made a sign to light up the Truck's side of the garage. Laser cut 1/8" aluminum plate, translucent acrylic, with LED backlight. Orange/White/Orange to match the truck.

Cool project!

Burgie70 · 02-02-2014, 05:26 PM

I put on a new fuel pump. What a pain trying to keep that rod up in there and get the gaskets situated. Required another set of hands from my friend. Now I know why people go with an electric one.

**Bob B.** · 02-02-2014, 06:41 PM

Went for a drive, gassed it up, and washed it!

BugzC10 · 02-02-2014, 07:10 PM

Quote:

Originally Posted by texjake

Here is a video clip. The clip may not be very loud, it's iPhone video quality if you know what I mean. I know it's not super loud but sure sounds a heck of a lot better than what the PO had on there. https://www.youtube.com/watch?v=t8QrWmi9pps

Sounds like a healthy Chevy "BIG" Block....

9teen69 · 02-02-2014, 11:02 PM

About half way done with PS conversion. Pulleys, gearbox, pitman arm installed. Pump painted and rebuilt. I like the way TXfirefighter painted his, wish it was powder coated but rattle can will do. I did have my pulleys power coated 60% gloss.

Sorry keeps flipping photos.

01-31-2014, 12:20 PM	#126
Mike_The_Grad Senior Member Join Date: Oct 2013 Location: Santa Paula, CA Posts: 622	Re: What did you do to your truck today? Chapter II This was 2 days ago. My first successful engine/trans pull. Had a couple buddies with a lot more experience than me, over to help. And I'm very glad they showed up. Saved me from making a very time consuming mistake since I was going to just yank the distributor out without finding tdc on #1 piston! Now begins the fun part! CLEANING! then paint. Also found out my timing chain cover is missing my degree timer. So now I gotta pull balancer and water pump.just one more thing to do... but it needs to be done. Might as well do it while its out in the open. I'm really excited to see how this is all gonna turn out. More pics soon to come Attached Images __________________ 1972 C/10 LWB - Mine 1964 C/10 LWB - My Dad's Instagram: Mike_The_Grad

01-31-2014, 03:11 PM	#127
VWNate1 Registered User Join Date: Feb 2012 Location: So. Cali. Posts: 2,656	Re: What did you do to your truck today? Chapter II Grimy but not really bad , it'll look great when you're finished . Did you remove the entire front clip as one piece ? . __________________ -Nate Geezer '49 3100 235 W/ Muncie SM420 SOLD '69 C/10 shortbed sidemount survivor 250 L6 W/ 350TH

01-31-2014, 09:16 PM	#128
texjake Registered User Join Date: Nov 2013 Location: Lubbock, TX Posts: 283	Re: What did you do to your truck today? Chapter II My Flowmasters came in today & got them installed. It sounds so much better now! And yes my interior is still gutted, waiting on parts to come in. Attached Images __________________ "Now all I need is a shop to go with my shop vac!"

02-01-2014, 12:49 PM	#134
tomshortwide69 Registered User Join Date: Jan 2014 Location: okay.oklahoma Posts: 41	Re: What did you do to your truck today? Chapter II

02-01-2014, 05:55 PM	#136
Lou Boffa Registered User Join Date: Jan 2013 Location: San Antonio, TX Posts: 733	Re: What did you do to your truck today? Chapter II couldn't help it. I'm a sucker for truck bling. Installed core support filler plates. Attached Images __________________ Figure out what you want--then figure out what you are willing to give up to get it.

02-01-2014, 06:54 PM	#138
Econman Registered User Join Date: Feb 2011 Location: Knoxville, TN Posts: 362	Re: What did you do to your truck today? Chapter II Haven't worked on it today. The rolling chassis is completed (rebuilt rears, new suspension, all grade 8 stainless hardware, stainless brake lines, stainless fuel lines, everything powder coated including rally wheels. Engine block, crank, rods/pistons and heads all in the machine shop. Just waiting to get them back to start building the engine back... I discovered a '72 Super C20 today. Was sold to a recycling center for scrap metal. Complete truck. Quite a bit of rust, but otherwise pretty straight. Camper Special with dual tanks. I'm hoping to buy the door panels out of it - they're in nice condition with wood grain inserts. If it isn't bought soon, I guess it will be crushed. It's been parked adjacent to the crusher awaiting a possible buyer for several months.

02-01-2014, 08:29 PM	#140
Lanman1972 Registered User Join Date: Dec 2013 Location: Omaha NE Posts: 620	Re: What did you do to your truck today? Chapter II I made a sign to light up the Truck's side of the garage. Laser cut 1/8" aluminum plate, translucent acrylic, with LED backlight. Orange/White/Orange to match the truck. Attached Images

02-02-2014, 05:26 PM	#147
Burgie70 Registered User Join Date: Jun 2013 Location: Grants Pass, Oregon Posts: 59	Re: What did you do to your truck today? Chapter II I put on a new fuel pump. What a pain trying to keep that rod up in there and get the gaskets situated. Required another set of hands from my friend. Now I know why people go with an electric one. __________________ 1970 C-10 350, 350 trans, ps,pb

02-02-2014, 06:41 PM	#148
Bob B. Senior Member Join Date: Aug 2005 Location: Los Angeles Posts: 1,348	Re: What did you do to your truck today? Chapter II Went for a drive, gassed it up, and washed it! __________________ 1967 GMC CM-2500 Camper Cruiser, 351E V-6, NP 435 4 speed, Dana 60, and factory A/C. 2012 GMC K-3500 WT regular cab, 6.0L Vortec, 6L90.

02-02-2014, 11:02 PM	#150
9teen69 Registered User Join Date: Sep 2002 Location: Austin, Texas Posts: 1,048	Re: What did you do to your truck today? Chapter II About half way done with PS conversion. Pulleys, gearbox, pitman arm installed. Pump painted and rebuilt. I like the way TXfirefighter painted his, wish it was powder coated but rattle can will do. I did have my pulleys power coated 60% gloss. Sorry keeps flipping photos. Attached Images __________________ 72 Cheyenne SWB C10 (daily driver) (Super fake cause I just love the glovebox emblem) 70 Camaro RS (frame-off in pieces) 70 Camaro RS (daily driver backup) 69 Custom LWB C10 (son now drives)



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.