''Project '64 SYT Super Yenko Truck"

[scotts62]

Man thats looking good! I like the fuel cell mount
And your floor is spotless compared to mine after a day of working on the truck..

[jgh64pkup]

it had about ten pounds of bondo

but its gone now

[jgh64pkup]

Originally Posted by scotts62

Man thats looking good! I like the fuel cell mount
And your floor is spotless compared to mine after a day of working on the truck..

thanks
its been worse but it was pretty bad then

[jgh64pkup]

this is what i did last night and this morning
i pulled the brake booster off
i also put a new master cylinder on it
the brake booster didnt work and the firewall was hacked up so i made an aluminum panel that covers the brake booster holes
then i polished it
the first pic is before and the others are after

[jgh64pkup]

no i dont like primer the things in primer are whats going to get a coat of sunburst orange
more pics

[jason65]

Nice work vato.

[jgh64pkup]

gracias hombre

[protrash64]

Good job on the ms/cyl. I was wondering if your fenders are solid without the inners installed?

[jgh64pkup]

yeah theyre fine i wouldnt sit on them but good enough to hold the frontend up
i want some porterbuilt inners which consist of two mounts and a tube
i will need them because im thinking about fiberglass fenders

[jgh64pkup]

i went to o'reillys yesterday and picked up some exhaust tips
my neighbor took me to the store and we messed with the idiot working at the counter i used to work at the real parts store down the street but oreillys is the only one who had exhaust tips
here are some pics

[1964C10]

Nice job on the M/C!

[jgh64pkup]

thanks i still have to paint it and bend the lines

[jgh64pkup]

i made a gas pedal last night out of aluminum
should i polish this or just leave how it is
sort of a brushed look
i have to make the brake pedal pad when i get some more aluminum
i need some ideas of how to mount it
heres some pics

[1964C10]

If you have one of those little portable sand blasters then that always gives it a nice "rough" finish that leaves future scratches somewhat hidden.

[Captainfab]

Originally Posted by 1964C10

If you have one of those little portable sand blasters then that always gives it a nice "rough" finish that leaves future scratches somewhat hidden.

I agree....plus you don't want the pedals too slippery.....especially the brake pedal

Might be a good place to add some flares to those holes if you have a way to do that......flared up of course.

[protrash64]

I wouldnt bother polishing your pedal, unless you wear fuzzy slippers when you drive. I'm sure your shoes will unpolish it pretty fast.

[jgh64pkup]

i have a sandblaster do you think that would look good
so any ideas on the brake pedal

[1964C10]

I am sure you have a little piece left over from what you made the pedals from, give it a shot and see if you like the look. Or do it on the back of the pedal that way if you dont like it none will see it.

[jgh64pkup]

thanks but no i dont have any left that is the same size peice i found laying outside
my dad has to redo the way he mounted his swamp cooler(in the window with about a 30''x15'' peice of aluminum)
im going to use that aluminum to make a switch panel gauge cluster and brake pedal

[Inverter]

Hit that pedal w/a vibrating sander and a 220 grit pad and call it done.

[jgh64pkup]

Originally Posted by Inverter

Hit that pedal w/a vibrating sander and a 220 grit pad and call it done.

thats actually what i did at first and didnt like
thanks though


ok the person that had this truck before obviously didnt know what they were doing and instead of recessing the dished in power steering box mount in the frame they just welded a chunk of another frame onto the original flat one
im changing over to manual steering but im going to go ahead and put the power steering mount on the frame just in case i change my mind later on
i still have to weld it in
i will get the welder back that i was using,tomorrow my neighbor loaned it to me (thanks Neil)
its a little hobart 140 MIG and works great
alright now for the pics
1st pic is before and the others are after
i thought the last 2 pics looked cool

[jgh64pkup]

alright im done
heres the pics
its got a lot of little fuzzy things in the paint
crappy towels
i just did a qiuck rattle can job on it

[Frizzle Fry]

Looks factory!

[jgh64pkup]

up close you can tell its not
well i cant because i did it
and stupid me welded up the holes to the core support mount
i was trying to make it look cleaner and didnt realize what i was welding up

[joe231]

what did that frame section come from?
It looks nice!!
good work!!