Project: Bad Bagged '68.5 - Page 6 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

abadsvt · 08-27-2007, 10:52 PM

Looks Sick!!!! These trucks looks so good low like that! I will be watching this build thread for sure!!!

jlaird · 09-17-2007, 05:47 PM

a little progress, actually it looks like I went backwards, because I took the cab off, but had to to chop the trailing arm crossmember. So that is what I finished (except for the exhaust cutouts). She cant go any lower, shes on the ground! Heres some pics. Next up is to make a crossmember that goes between the trailing arm x-member and the axle.

LUV2XCLR8 · 09-17-2007, 06:27 PM

Looking awesome, can't wait to see the body on that frame

jlaird · 09-25-2007, 07:35 PM

Got the driveshaft loop x-member finished as well as the exhaust cutouts almost done. Some pics:

BigShoe24 · 09-26-2007, 01:44 AM

Very nice work, keep it up. How did u determine the drive shaft loop height? Without transmission in.

jlaird · 09-26-2007, 08:24 AM

Quote:

Originally Posted by BigShoe24

Very nice work, keep it up. How did u determine the drive shaft loop height? Without transmission in.

I've got a two piece drive shaft which means it's at a fixed height at the carrier bearing.

72BlckButy · 09-26-2007, 08:29 AM

Nice looking truck!

Frizzle Fry · 09-26-2007, 11:55 AM

Quote:

Originally Posted by jlaird

I've got a two piece drive shaft which means it's at a fixed height at the carrier bearing.

That's good, becuase I was gonna tell you that I had to raise the upper "hoop" on the TA X-Member for my one-piece driveshaft + 8" notch. With that notch you definately would too, but a two pice DS takes care of that! Nice work

What's the dia. on your exhaust cut-outs?

jlaird · 09-26-2007, 12:12 PM

They have a 4" inner diameter, so will be good for something like a 3" exhaust pipe.

impala_631 · 10-02-2007, 03:11 AM

i know its a little bite late but heres a crappy pic of my steering linkage made from 2 astro van linkages

IvelDesigns · 10-02-2007, 11:26 AM

great work man. glad to see some progress.

on the topic of the split drive shaft. Are you concerned at all that the travel of the axle will pull on the carrier bearing? obviously normal up and down is fine, but with the extra travel that you'd get with air bags, i'm curious if the axle will put more preasure on the CB.

in my application (bagged with a split shaft) it didn't seem to put any additional pressure on the CB, but i only have a C-notch, not a step. Also, my bags are mounted on the T-arms, so my travel is not much.

jlaird · 10-02-2007, 11:52 AM

Quote:

Originally Posted by IvelDesigns

great work man. glad to see some progress.

on the topic of the split drive shaft. Are you concerned at all that the travel of the axle will pull on the carrier bearing? obviously normal up and down is fine, but with the extra travel that you'd get with air bags, i'm curious if the axle will put more preasure on the CB.

in my application (bagged with a split shaft) it didn't seem to put any additional pressure on the CB, but i only have a C-notch, not a step. Also, my bags are mounted on the T-arms, so my travel is not much.

I'm really not worried about that at all. I set up the driveshaft and CB to work properly with the frame rails only being 5 inches off the ground. This truck is not going to see a lot of vertical travel(especially at cruising speeds) that will be putting any sort of stress on the CB. I'm not suspension expert, just seems like common sense to me.

SBCustoms · 11-07-2007, 12:22 AM

wheres the progress??????????????????

jlaird · 11-08-2007, 09:00 PM

frame and all the suspension parts are going to the powder coater tomorrow. It will be nice to see something in my garage that is one color! Cant wait....

I will post pictures when I get it back. They said two weeks.

XXL · 11-08-2007, 09:06 PM

Quote:

Originally Posted by jlaird

They said two weeks.

Uh oh... that's a notorious statement. Do you know how many times I've heard "two [more] weeks" from body shops and "body shops?"

Hopefully your powder guys can handle it.

jkade · 11-09-2007, 06:27 PM

Couple questions, how long is your 4 link? How big of a notch did you install? Keep up the good work.

jlaird · 11-09-2007, 10:05 PM

Quote:

Originally Posted by jkade

Couple questions, how long is your 4 link? How big of a notch did you install? Keep up the good work.

If memory serves me correctly (can't go out and measure because everything is at the powdercoaters), the 4link bars are 32 inches long and the notch ended up being about 9-10 inches.

Sweet 85 C10 · 11-24-2007, 01:52 PM

Nice! I havent been up here in a while I must say! Real Clean work!

onetonk5 · 11-24-2007, 10:53 PM

why leave the trailing arm crossmember in if your not using the trailing arms?

jlaird · 11-25-2007, 08:58 AM

Quote:

Originally Posted by onetonk5

why leave the trailing arm crossmember in if your not using the trailing arms?

Two reasons: Strength and holds my two-piece driveshaft bracket.

So I decided to have a local engine builder build me an engine over buying a crate. I think I'm getting a pretty darn good deal. He's building me a mild 350 with vortec heads for a little more than the cost of GM's 290 horse crate. I should have that by end of December.

XXL was right on the money with the damn powder coaters. They said it should be around two weeks. Two weeks was yesterday. Their yet to call me with my final quote. I hate dealing with people like this... I guess I just have to be patient.

XXL · 11-25-2007, 10:17 AM

Quote:

Originally Posted by IvelDesigns

Also, my bags are mounted on the T-arms, so my travel is not much.

Just re-reading this thread and I stumbled on this... you're probably getting MORE travel than jlaird. With his bags coming straight off the rearend, he's getting pretty much 1:1 lift. With yours on the trailing arms (assuming at the stock spring location), you're getting a little leaverage since you're "up the lever" a bit from the rearend.

If you're not getting any carrier bearing issues, he should be just fine.

XXL · 11-25-2007, 10:20 AM

Quote:

Originally Posted by jlaird

They said it should be around two weeks. Two weeks was yesterday. Their yet to call me with my final quote. I hate dealing with people like this... I guess I just have to be patient.

Makes you want to show up with a trailer and load your stuff up... but they've generally got us by the... uh... throat. So we have to put up with stuff like that. One day somebody with a keen sense of customer satisfaction is going to open a shop to do this stuff, and he's going to grab much of the market. Until then

Bastages!

OLDIRON69 · 12-01-2007, 02:37 PM

Very nice build! I love lowered trucks, mine is a worker so laying frame is out of the Q. One day when I retire the truck from working........

AGAIN, GREAT JOB!

SBCustoms · 01-12-2008, 07:17 PM

how bout the powder coating? still havent got it back? any word?

jlaird · 01-13-2008, 05:30 AM

Got it back on wednesday. What a PITA. These guys took their sweet a$$ time with it. They had it for 2 months. And listen to this, they called me Monday at about 10am to say they were going to start it and to confirm I didn't change my mind on anything which was nice. I actually ended up having them do just the frame and blast everything else for me to paint myself.(I wanted to save some $$) They called me back at around 2pm to tell me it was done. They made me wait 2 MONTHS for about 4 hours of work. They have some workflow/timing issues to say the least.

The frame came out good though. I will post pics soon.

08-27-2007, 10:52 PM	#126
abadsvt Senior Member Join Date: Aug 2006 Location: Atascadero, CA Posts: 1,152	Re: progress pics Looks Sick!!!! These trucks looks so good low like that! I will be watching this build thread for sure!!! __________________ (Project truck) 1970 C10 under complete transformation My current build thread http://67-72chevytrucks.com/vboard/s...d.php?t=212871 Other project: C5 corvette swap into 70 c10 http://67-72chevytrucks.com/vboard/s...=1#post2413517 On Hold

09-17-2007, 05:47 PM	#127
jlaird Senior Member Join Date: May 2004 Location: johnstown, NY Posts: 2,393	Re: progress pics a little progress, actually it looks like I went backwards, because I took the cab off, but had to to chop the trailing arm crossmember. So that is what I finished (except for the exhaust cutouts). She cant go any lower, shes on the ground! Heres some pics. Next up is to make a crossmember that goes between the trailing arm x-member and the axle. Last edited by jlaird; 09-17-2007 at 05:48 PM.

09-17-2007, 06:27 PM	#128
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,484	Re: progress pics Looking awesome, can't wait to see the body on that frame __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T

09-25-2007, 07:35 PM	#129
jlaird Senior Member Join Date: May 2004 Location: johnstown, NY Posts: 2,393	Re: progress pics Got the driveshaft loop x-member finished as well as the exhaust cutouts almost done. Some pics:

09-26-2007, 01:44 AM	#130
BigShoe24 True Addiction Join Date: Nov 2005 Location: FTL Posts: 415	Re: progress pics Very nice work, keep it up. How did u determine the drive shaft loop height? Without transmission in.

09-26-2007, 08:29 AM	#132
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: progress pics Nice looking truck! __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package) Last edited by 72BlckButy; 09-26-2007 at 08:29 AM.

09-26-2007, 12:12 PM	#134
jlaird Senior Member Join Date: May 2004 Location: johnstown, NY Posts: 2,393	Re: progress pics They have a 4" inner diameter, so will be good for something like a 3" exhaust pipe.

10-02-2007, 03:11 AM	#135
impala_631 :( BYEBYE :( Join Date: Sep 2007 Location: terre haute indiana Posts: 200	Re: progress pics i know its a little bite late but heres a crappy pic of my steering linkage made from 2 astro van linkages __________________ THE IMPALA 74 C-10 "SNOTTROCKET"BUILD UP http://www.layitlow.com/forums/index...owtopic=370899

10-02-2007, 11:26 AM	#136
IvelDesigns Commander Taco Bello Join Date: Sep 2006 Location: Des Moines, Iowa Posts: 2,232	Re: progress pics great work man. glad to see some progress. on the topic of the split drive shaft. Are you concerned at all that the travel of the axle will pull on the carrier bearing? obviously normal up and down is fine, but with the extra travel that you'd get with air bags, i'm curious if the axle will put more preasure on the CB. in my application (bagged with a split shaft) it didn't seem to put any additional pressure on the CB, but i only have a C-notch, not a step. Also, my bags are mounted on the T-arms, so my travel is not much. __________________ Bagged '50 3600 - Bumper punchin' road kill since 2009... Bagged '69 C10 Longbed - Bumper punchin' road kill since 2007...

11-07-2007, 12:22 AM	#138
SBCustoms Complete Street Customization Join Date: Jan 2007 Location: Knoxville, TN Posts: 103	Re: progress pics wheres the progress?????????????????? __________________ 1968 GMC SWB (Build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=269230) 1998 Chevrolet Silverado Z71 Southern Born Customs Knoxville, TN 865-934-9126

11-08-2007, 09:00 PM	#139
jlaird Senior Member Join Date: May 2004 Location: johnstown, NY Posts: 2,393	Re: progress pics frame and all the suspension parts are going to the powder coater tomorrow. It will be nice to see something in my garage that is one color! Cant wait.... I will post pictures when I get it back. They said two weeks.

11-09-2007, 06:27 PM	#141
jkade Senior Member Join Date: Nov 2005 Location: AL Posts: 2,519	Re: progress pics Couple questions, how long is your 4 link? How big of a notch did you install? Keep up the good work.

11-24-2007, 01:52 PM	#143
Sweet 85 C10 OG Join Date: Sep 2007 Location: Orlando Florida Posts: 146	Re: progress pics Nice! I havent been up here in a while I must say! Real Clean work!

11-24-2007, 10:53 PM	#144
onetonk5 Cereal Killer Join Date: Jan 2006 Location: Montgomery, Alabama Posts: 639	Re: progress pics why leave the trailing arm crossmember in if your not using the trailing arms? __________________ If I dont do it....somebody else will.

12-01-2007, 02:37 PM	#148
OLDIRON69 Registered User Join Date: Mar 2007 Location: Ben Wheeler,Texas Posts: 992	Re: progress pics Very nice build! I love lowered trucks, mine is a worker so laying frame is out of the Q. One day when I retire the truck from working........ AGAIN, GREAT JOB! __________________ 05 2500HD 6.0 excab 69 LWB-Gone but not forgotten! 68 Dodge Charger 383/727 69 Dodge Charger-440/4spd



Register or Log In To remove these advertisements.

01-12-2008, 07:17 PM	#149
SBCustoms Complete Street Customization Join Date: Jan 2007 Location: Knoxville, TN Posts: 103	Re: progress pics how bout the powder coating? still havent got it back? any word? __________________ 1968 GMC SWB (Build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=269230) 1998 Chevrolet Silverado Z71 Southern Born Customs Knoxville, TN 865-934-9126

01-13-2008, 05:30 AM	#150
jlaird Senior Member Join Date: May 2004 Location: johnstown, NY Posts: 2,393	Re: progress pics Got it back on wednesday. What a PITA. These guys took their sweet a$$ time with it. They had it for 2 months. And listen to this, they called me Monday at about 10am to say they were going to start it and to confirm I didn't change my mind on anything which was nice. I actually ended up having them do just the frame and blast everything else for me to paint myself.(I wanted to save some $$) They called me back at around 2pm to tell me it was done. They made me wait 2 MONTHS for about 4 hours of work. They have some workflow/timing issues to say the least. The frame came out good though. I will post pics soon.

Register or Log In To remove these advertisements.