AZ Cabs for parts/pieces

[t korinek]

djgebert, lets figure $25 shipping on this, if its any less I'll refund the difference.

Elliot949, haven't had a chance to check out a floor section yet.

Tilldogg, here's a pic of the area I was going to cut for you.

72 tutone, here's pics of the pieces I have cut for you, these will not fit in a med flat rate box like I had planned,I can trim them until they do or you can pay another $5 to take them like they are in a large flate rate box.
Thanks,
Tom

[Elliot949]

Originally Posted by t korinek

djgebert, lets figure $25 shipping on this, if its any less I'll refund the difference.

Elliot949, haven't had a chance to check out a floor section yet.

Tilldogg, here's a pic of the area I was going to cut for you.

72 tutone, here's pics of the pieces I have cut for you, these will not fit in a med flat rate box like I had planned,I can trim them until they do or you can pay another $5 to take them like they are in a large flate rate box.
Thanks,
Tom

Ok.. Thanks... I will keep a eye on it...

[djgebert]

Thanks Tom, payment has been sent.

[Tilldogg]

Tom
that looks good to me, great stuff, let me have a total and i will get you paid,

Thank you

[72tutone]

Originally Posted by t korinek

djgebert, lets figure $25 shipping on this, if its any less I'll refund the difference.

Elliot949, haven't had a chance to check out a floor section yet.

Tilldogg, here's a pic of the area I was going to cut for you.

72 tutone, here's pics of the pieces I have cut for you, these will not fit in a med flat rate box like I had planned,I can trim them until they do or you can pay another $5 to take them like they are in a large flate rate box.
Thanks,
Tom

Tom-
Can you cut about an 1/4 up or so from the drip rail? The top part of the cab I dont need so much Would they then fit?

[mjgord51]

Originally Posted by mjgord51

Thanks anyway I have seen same condition here for $35.00 shipped, if you'll do that I'll take it.

Did you forget about me or are you Not interested in my final offer?

[t korinek]

Originally Posted by mjgord51

Did you forget about me or are you Not interested in my final offer?

Hey mjgord51, I think I'll Pass on your offer, this isnt perfect, but I don't get too many usable used ones anymore.

Thanks
Tom
Posted via Mobile Device

[mjgord51]

Under stand, Thanks anyway, mjgord51

[72tutone]

Tom-
Thanks for the cab parts. Received them yesterday.

[Ol 67 C10]

This is the piece that I need. I need the flange left on the front where it welds to the firewall and up on the first ledge where the trans tunnel is. Hopefully that makes since. Lol.

[t korinek]

ol67c10 I have that piece for $33 shipped

Elliot, these are the best inside floor pieces I have,semi solid, but have heavy pitting, in my opinion not worth the time to cut out & pay shipping on. I have the Reproduction extended inner rockers available for $65 ea have you seen them?

[Ol 67 C10]

I'll take it as long as it's still solid. Let me know how you want to get paid. I can send payment tomorrow. Thanks, Wes.

[t korinek]

ol67C10, PM sent, that area is solid, do you need the studs too? if so $3 each.
Thanks,
Tom

[Ol 67 C10]

Let me see how rusted my studs are tomorrow and I'll let you know. Thanks!

[Ol 67 C10]

Payment sent for the floor patch and ( 2 ) ball studs. Thanks, Wes

[t korinek]

ol 67 c10- Please look at pics of panel I have cut out for you, there is heavy pitting in the area of the studs, 3 small holes through, let me know if this piece will work for you, if not i'll refund your payment.
Thanks,
Tom

[Ol 67 C10]

Tom, I think I'll pass on that piece of floor pan. Do you have any other 67 parts you could send instead of refund? Thanks, Wes

[Ol 67 C10]

Sent you a pm with parts I'd be interested in.

[ekgguy]

I am looking for this part of the cab, A pillars and roof



I need about 1 foot back from the front of the drip rail and about 1 foot down both A pillars.

Let me know if that is possible and shipping to 77338

Thanks a bunch...

Matt

[t korinek]

ekkguy I have that patch panel $60 + shipping would probably be around $35

[jasonmiddlebrooks]

I see you are still cutting some off the cabs you have. I have a 70 c10 and I am looking for the driver side rear corner. Here are the pictures. Not really looking for any of the floor just the outside wrapped around the door jamb so I will have plenty of room to cut what I don't need. If it is easier to cut the floor and include it I can deal with whatever I need to trim off. Let me know what you think a price would be and shipping to 30228. Thanks and look forward to hearing from you.

[ekgguy]

Originally Posted by t korinek

ekkguy I have that patch panel $60 + shipping would probably be around $35

Thanks Tom. I am looking into an entire cab right now. I should know by Friday if that isn't to late for you.

Matt

[t korinek]

This is all I have for a gas tank area panel, it was already cut off & may be a little small for what your doing.

[jasonmiddlebrooks]

Yes I believe that does not have the coverage I need. Thanks for the info. Let me know if you come across another one.

[mjgord51]

The heater Control arrived on time and in the shape/description stated, thanks Tom, mjgord51