|
09-12-2011, 06:55 PM | #1 |
Registered User
Join Date: Mar 2010
Location: a t w a t e r cali 95301
Posts: 10,713
|
Re: 67 cheby's Dropmember build thread
looking good.
|
09-12-2011, 10:22 PM | #2 |
low n' slo
Join Date: Mar 2009
Location: rosenberg, texas
Posts: 5,170
|
Re: 67 cheby's Dropmember build thread
nice!
i think i can see your light at the end of the tunnel all the way down in here texas lol
__________________
67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____|__|__\__ ,.,,,.,.,,.,|_O _______ O_] |
09-13-2011, 09:53 AM | #3 |
Registered User
Join Date: Sep 2008
Location: Spring TX
Posts: 67
|
Re: 67 cheby's Dropmember build thread
What is the backspacing on the rear wheels? I really like how close the wheel/tire is to the bedside. Really looks clean that way.
|
09-13-2011, 09:58 AM | #4 |
67cheby
Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: 67 cheby's Dropmember build thread
the back wheels are 22x10's with 7 1/2 inches of backspacing, but i am running a billet spacer with a 69 up rearend , i couldnt see spending the BIG BUCKS....that it takes to get these kind of wheels custom made to exactly what i wanted so i made these work with the setup i have , bought them on this board in the for sale section...THANKS VA72c10 once again, I LOVE my wheels
|
09-13-2011, 10:40 AM | #5 |
Senior Member
Join Date: Mar 2011
Location: West Plains, Missouri
Posts: 7,559
|
Re: 67 cheby's Dropmember build thread
I take off one day and you add two pages to the build, way to go. Love the tubs and the truck looks great, nice job.....Jim
__________________
my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br /> |
09-13-2011, 10:44 AM | #6 |
67cheby
Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: 67 cheby's Dropmember build thread
trying to make up for 6 months of adding NOTHING !!
|
09-14-2011, 09:24 AM | #7 |
67cheby
Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: 67 cheby's Dropmember build thread
did i mention how much i love having my truck at home ..... only had about 1 hour to work on it last night but i started with the used Painless wiring i got from a board member, and stripped all of the tape and loom off it, stripped the wires i didnt need from the engine compartment, and started temporarily routing the wires so i can figure out lengths and routing paths !! It was great if i can get just 1 hour of stuff done a day ...it is MOVING FORWARD !!
|
09-14-2011, 10:37 AM | #8 | |
Still plays with trucks
Join Date: Jul 2009
Location: Spokane, WA
Posts: 3,556
|
Re: 67 cheby's Dropmember build thread
Quote:
The panel could cover the whole vent opening to seal it off too.
__________________
miSSed opportunity - ground up creation of an AWD 1994 454 SS that never was http://67-72chevytrucks.com/vboard/s...d.php?t=795577 69 C10 shortbed stepside 400 small block - built like what a super sport truck could have been 69 K20 lwb TBI 350 4L60E NP208 14-bolt Dana-44 w/disc 68 Camaro SS / RS 500hp 439 inch roller cam big block 4L80E 79 Malibu TPI 350 4L60 w/ Z28 steering & sway bars |
|
09-14-2011, 11:32 AM | #9 |
67cheby
Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: 67 cheby's Dropmember build thread
yes i am building a panel that bolts in and out of the vent hole, and then covering in with , custom made speaker kick panels
|
09-14-2011, 09:13 PM | #10 |
Tot Roddin'
Join Date: Apr 2005
Location: Mid-MO
Posts: 24,461
|
Re: 67 cheby's Dropmember build thread
Lookin' good!
Glad to see it's back home for some regular (ahem,... daily) updates.
__________________
-Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package) |
09-15-2011, 05:23 PM | #11 |
67cheby
Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: 67 cheby's Dropmember build thread
LOL...yep, gonna get all of my wiring routed for mock up !!
|
09-15-2011, 07:17 PM | #12 |
PROJECT 7DEUCE
Join Date: Dec 2002
Location: GRANTS PASS OR
Posts: 21,608
|
Re: 67 cheby's Dropmember build thread
Please tell me your gonna run that wire under the core support????
__________________
GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P.. |
09-15-2011, 09:58 PM | #13 |
67cheby
Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: 67 cheby's Dropmember build thread
no it will run through it, completely concealed !! all wire except for the ones running to the absolute necessary stuff will be hidden, along with ac and heater hoses
|
09-16-2011, 08:56 AM | #14 |
PROJECT 7DEUCE
Join Date: Dec 2002
Location: GRANTS PASS OR
Posts: 21,608
|
Re: 67 cheby's Dropmember build thread
Hell yes I was hoping you were gonna say that..
__________________
GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P.. |
09-16-2011, 09:11 AM | #15 |
67cheby
Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: 67 cheby's Dropmember build thread
yeterday i stopped by a swap meet the first pic is what i couldnt pass up for $10 buckaroos, mocking up my vintage air so i can figure out where to put my computer brain, and where to run my fuel injection wiring out of the firewall (i am thinking in the middle right behind the distributor), then got the box put back in working on getting everything set so i can start stretching the fleece on it to make all of the contours ! oh brought the painless wiring to work with me today to start cleaning it up and checking all of the wires on it !
|
09-16-2011, 12:08 PM | #16 |
67cheby
Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: 67 cheby's Dropmember build thread
i am thinking about going to GoodGuys on Oct 1st if i can get a couple orders for SLOSH TUBZ, to take and deliver, give me a shout if anyone is interested ! FREE DELIVERY !!
|
09-16-2011, 12:45 PM | #17 | |
Still plays with trucks
Join Date: Jul 2009
Location: Spokane, WA
Posts: 3,556
|
Re: 67 cheby's Dropmember build thread
Quote:
The speaker box looks great.
__________________
miSSed opportunity - ground up creation of an AWD 1994 454 SS that never was http://67-72chevytrucks.com/vboard/s...d.php?t=795577 69 C10 shortbed stepside 400 small block - built like what a super sport truck could have been 69 K20 lwb TBI 350 4L60E NP208 14-bolt Dana-44 w/disc 68 Camaro SS / RS 500hp 439 inch roller cam big block 4L80E 79 Malibu TPI 350 4L60 w/ Z28 steering & sway bars |
|
09-16-2011, 01:08 PM | #18 |
67cheby
Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: 67 cheby's Dropmember build thread
thanks..i just cant pass them up i love these valve covers...the box will look alot better once i start stretching the fleece on it , it will really contour nicely then !!
|
09-16-2011, 01:12 PM | #19 | |
Registered User
Join Date: Dec 2008
Location: Berryville, AR
Posts: 792
|
Re: 67 cheby's Dropmember build thread
Quote:
BTW what engine are you looking putting in?
__________________
Rex |
|
09-16-2011, 11:53 PM | #20 |
Registered User
Join Date: Jun 2008
Location: pensacola fl
Posts: 3,073
|
Re: 67 cheby's Dropmember build thread
Then the kid comes out and ask "why is your truck STILL broken daddy" lol
Now you have to stare at it some more. Posted via Mobile Device
__________________
68 BB burb build thread Scott's super slam front/rear http://67-72chevytrucks.com/vboard/s...d.php?t=378084 |
09-17-2011, 12:12 AM | #21 |
Sofa King Crazy!!
Join Date: Oct 2008
Location: Houston, TX
Posts: 3,090
|
Re: 67 cheby's Dropmember build thread
Great score on the valve covers, I love em........then again I am biased!!
__________________
You found the Tater. My Blazer Build (New) - http://67-72chevytrucks.com/vboard/s...d.php?t=654650 My 67 Build - http://67-72chevytrucks.com/vboard/s...d.php?t=335650 67 Chevy LWB big window a/c AKA TOTALLED BY A JACKASS. 1972 2wd Blazer "Porterbuilt and Sloshed" |
09-17-2011, 09:33 AM | #22 |
67cheby
Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: 67 cheby's Dropmember build thread
me to i just need to figure out a way to fill mine with oil and make them breath...... maybe like HAZEL, but i still have to figure out how to fill it with oil ??
|
09-17-2011, 09:38 AM | #23 |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,009
|
Re: 67 cheby's Dropmember build thread
Valve covers unbolt..... How often do you plan to fill it w/oil?
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
09-17-2011, 09:41 AM | #24 |
67cheby
Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: 67 cheby's Dropmember build thread
LOL....that never even crossed my mind !!
|
09-17-2011, 09:40 AM | #25 |
67cheby
Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: 67 cheby's Dropmember build thread
figured out how to mount my computer brain and fuse block last night, next step will be making trim panels to hide it all....geez there is not very much space behind these dashes !!
|
Bookmarks |
Tags |
fiberglass inner fenders, pb hood hinges ", w/pb 4 link |
|
|