PO has me PO'd - Page 66 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**jaros44sr** · 11-25-2018, 06:00 PM

Epic fail, part #2, 1A

still scrunky, used 3/4" wire care and it slips under corrugated , with bushing taped in. Marked with paint stick to keep it aligned. Now has support

**zicc1835** · 12-08-2018, 09:38 AM

that cleaned up real nice Jim whats it lok like on the engine side ?

**jaros44sr** · 12-08-2018, 12:12 PM

Quote:

Originally Posted by zicc1835

that cleaned up real nice Jim whats it lok like on the engine side ?

Shorten wire, reattach connecters, repin wires, seals, study schmatic
I guess you could say that was a test fit....
probably pull runner, to gain access

My head hurts just thinking about it.

[url=https://flic.kr/p/PF9V1a]20181208_102117

**jaros44sr** · 12-08-2018, 07:23 PM

Zicc, thanks for the interest, but I may get my oil pan back up first, since the oil has drained out of the engine, I want to prime it back up thru the new oil filter and lines I installed, see what the gauge reads, and then rotate crank shaft, it seems a bit solid. Maybe put something down the bores

any work on your project or are you still traveling alot?

**zicc1835** · 12-08-2018, 07:59 PM

Quote:

Originally Posted by jaros44sr

Zicc, thanks for the interest, but I may get my oil pan back up first, since the oil has drained out of the engine, I want to prime it back up thru the new oil filter and lines I installed, see what the gauge reads, and then rotate crank shaft, it seems a bit solid. Maybe put something down the bores

any work on your project or are you still traveling alot?

Been travling alot Jim, with the fires in NorCal and acquisitions across the US the company is doing, been a busy year and will continue at least thru Q-1. only getting some of the plumbing, brakelines almost complete, exhaust next cab on for fitment hope i can do all that this winter....i been following your progress

thanks Merry Christmas
Jess

**jaros44sr** · 12-08-2018, 09:35 PM

I gotta say I miss the fires I used to put out for the companies I worked for over the years(sometimes) then I work on my truck and forget it. But, I do miss the money

Maybe we can get together over the holidays, bring wifey

want to buy a bore scope, see what's going on in the chambers

CJM72 · 01-06-2019, 10:04 AM

Jaros, I just want to say I appreciate your consistency. As a guy that works in fits and starts, I love seeing people making regular progress! How far are you from running and driving this rig?

**jaros44sr** · 01-07-2019, 05:02 PM

Quote:

Originally Posted by CJM72

Jaros, I just want to say I appreciate your consistency. As a guy that works in fits and starts, I love seeing people making regular progress! How far are you from running and driving this rig?

First off, thank you! It is a labor of love, but being retired it is also a great way to keep my mind and hands busy...

Secondly, I have no idea or plans for that outcome, other then a anniversary coming up in June20th for a celebration of the brand in Harrisburg, Pa. Hope I don't have to trailer it there, EMBARRISING, but, I do want to install a dry sump system, next on the list of to dos

Fits and starts should be my montra

Just walked out of court, beat a speeding ticket for 55mph in a 25mph work zone, pulled the marine corp card and he said" sempre fi"

**jaros44sr** · 01-08-2019, 03:42 PM

[url=https://flic.kr/p/23u9Kfg]20190108_113522

[url=https://flic.kr/p/2cZz3sj]20190108_113545

secret santa was my daughter in law

**jaros44sr** · 01-12-2019, 07:54 AM

[url=https://flic.kr/p/23yjDy2]20190112_064458

sorta ol school....reminds me of my sun tach mount in the '62 chevy

[url=https://flic.kr/p/2cLVkzV]20190112_064550

Never heard of a 1/2-150, so looked it up on the www, seems to be a schedule 40 pipe

**jaros44sr** · 01-18-2019, 09:54 AM

still searching for the right position to mount gauge. using the heater control mount screw (1/4-20) I put a hex drive stud in it with a flange nut.

DON'T use slotted screws that come with the mounting kit, the screw driver will slip and gouge the mount or worse yet your dash

I think I will try to use the other mounting screw for the heater control, since this location looks like it may cause problems with my shifter

[url=https://flic.kr/p/2egy1VX]20190117_102220

Lokin4AReason · 01-28-2019, 01:25 PM

boy that truck is getting some serious love .... nice job in getting it together

**jaros44sr** · 01-29-2019, 08:54 AM

Quote:

Originally Posted by Lokin4AReason

boy that truck is getting some serious love .... nice job in getting it together

Thanks, up to this time, everything was just a mock up, now, problems have to be solved and final fitment needs to happen. Soooo, that is what is taking place, wish me luck going forward

**jaros44sr** · 01-30-2019, 10:36 AM

as you can see the angle of the sport buckets have the angle wrong, so it will have to be the utility seat bracket, the keeper bracket is not on the ps, and when done will raise the seat up about 1 1/2"

[url=https://flic.kr/p/2dnVHef]20190129_103844

[url=https://flic.kr/p/23SvT4D]20190129_103358

**jaros44sr** · 01-30-2019, 10:41 AM

[url=https://flic.kr/p/2dmRq3A]20190128_093452

PS

**jaros44sr** · 01-30-2019, 11:41 AM

[url=https://flic.kr/p/23TtUdk]20190130_101754

[url=https://flic.kr/p/23TusBP]20190130_103005

taking bolts out, 2 snapped sounds like they may break, so put studs in, will reinstall with lock tite, easy enough to put a torch up there to break bond if need be

X is where the fitting goes, pretty big cavity in trans

[url=https://flic.kr/p/SmNpbA]20190130_102840

backing plate,

**richard2717** · 01-30-2019, 12:18 PM

They look like McMaster packages

**jaros44sr** · 01-30-2019, 06:15 PM

Quote:

Originally Posted by richard2717

They look like McMaster packages

They're great aren't they, one day to my door, if it is in stock. any fastner I can think of! probably should have gotten 12 point, oh well next order

**jaros44sr** · 01-30-2019, 09:38 PM

Whiskey :30

[url=https://flic.kr/p/SnefNo]20190130_203541

**jaros44sr** · 02-01-2019, 11:00 AM

I like to use a live center when tapping, keeps the threads in proper alignment

[url=https://flic.kr/p/2d8Ugv8]20190201_084147
while raceting tap
Also, I like to use a rachet tap handle,
pulling down on the quill , and rotate cw with tap

[url=https://flic.kr/p/2d8Ugv8]20190201_084147

**jaros44sr** · 02-01-2019, 12:12 PM

[url=https://flic.kr/p/2d8Ww5e]20190201_093600

[url=https://flic.kr/p/QLqQc2]20190201_093518

**zicc1835** · 02-04-2019, 09:52 PM

Bottoms up..Jim

**jaros44sr** · 02-06-2019, 05:17 PM

Thanks Jesse
Decided to put on the seat backs, ss#10x 3/4" screws, I hate phillip head screws, ordered some square drive today from Mcmaster Carr

I watch a show on Utube and he says to wax paint and rusty metal with tolette bowl wax(new) ring . So for 6.00 , I thought I would try it on my seat backs. Keeps the patina I was looking for, but protects the metal from further rust

[url=https://flic.kr/p/2dvKjEu]20190206_085314

pics don't want to load

**jaros44sr** · 02-06-2019, 07:13 PM

[url=https://flic.kr/p/2exajDJ]20190206_085341

**jaros44sr** · 02-07-2019, 10:59 AM

[url=https://flic.kr/p/2dvSYJG]20190206_112501

It's in , very easy to match up studs with feet

12-08-2018, 07:23 PM	#4
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,704	Re: PO has me PO'd Zicc, thanks for the interest, but I may get my oil pan back up first, since the oil has drained out of the engine, I want to prime it back up thru the new oil filter and lines I installed, see what the gauge reads, and then rotate crank shaft, it seems a bit solid. Maybe put something down the bores any work on your project or are you still traveling alot? __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

12-08-2018, 09:35 PM	#6
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,704	Re: PO has me PO'd I gotta say I miss the fires I used to put out for the companies I worked for over the years(sometimes) then I work on my truck and forget it. But, I do miss the money Maybe we can get together over the holidays, bring wifey want to buy a bore scope, see what's going on in the chambers __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

01-06-2019, 10:04 AM	#7
CJM72 Registered User Join Date: Aug 2015 Location: Raynham, MA Posts: 222	Re: PO has me PO'd Jaros, I just want to say I appreciate your consistency. As a guy that works in fits and starts, I love seeing people making regular progress! How far are you from running and driving this rig? __________________ My LS Swap: http://67-72chevytrucks.com/vboard/s...d.php?t=718573

01-08-2019, 03:42 PM	#9
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,704	Re: PO has me PO'd [url=https://flic.kr/p/23u9Kfg]20190108_113522 [url=https://flic.kr/p/2cZz3sj]20190108_113545 secret santa was my daughter in law __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

01-18-2019, 09:54 AM	#11
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,704	Re: PO has me PO'd still searching for the right position to mount gauge. using the heater control mount screw (1/4-20) I put a hex drive stud in it with a flange nut. DON'T use slotted screws that come with the mounting kit, the screw driver will slip and gouge the mount or worse yet your dash I think I will try to use the other mounting screw for the heater control, since this location looks like it may cause problems with my shifter [url=https://flic.kr/p/2egy1VX]20190117_102220 __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

11-25-2018, 06:00 PM	#1
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,704	Re: PO has me PO'd Epic fail, part #2, 1A still scrunky, used 3/4" wire care and it slips under corrugated , with bushing taped in. Marked with paint stick to keep it aligned. Now has support __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 11-25-2018 at 08:22 PM.

12-08-2018, 09:38 AM	#2
zicc1835 Senior Member Join Date: Mar 2011 Location: Hanover NJ Posts: 4,252	Re: PO has me PO'd that cleaned up real nice Jim whats it lok like on the engine side ? __________________ Doc & Kim build http://67-72chevytrucks.com/vboard/s...d.php?t=722288 I am from the desert http://67-72chevytrucks.com/vboard/s...d.php?t=650332 basket case build SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=648557

01-12-2019, 07:54 AM	#10
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,704	Re: PO has me PO'd [url=https://flic.kr/p/23yjDy2]20190112_064458 sorta ol school....reminds me of my sun tach mount in the '62 chevy [url=https://flic.kr/p/2cLVkzV]20190112_064550 Never heard of a 1/2-150, so looked it up on the www, seems to be a schedule 40 pipe __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

01-28-2019, 01:25 PM	#12
Lokin4AReason Registered User Join Date: Oct 2014 Location: somewhere . . . Posts: 969	Re: PO has me PO'd boy that truck is getting some serious love .... nice job in getting it together __________________ dont want to hear excuses, i want to hear solution(s)

01-30-2019, 10:36 AM	#14
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,704	Re: PO has me PO'd as you can see the angle of the sport buckets have the angle wrong, so it will have to be the utility seat bracket, the keeper bracket is not on the ps, and when done will raise the seat up about 1 1/2" [url=https://flic.kr/p/2dnVHef]20190129_103844 [url=https://flic.kr/p/23SvT4D]20190129_103358 __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

01-30-2019, 10:41 AM	#15
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,704	Re: PO has me PO'd [url=https://flic.kr/p/2dmRq3A]20190128_093452 PS __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

01-30-2019, 11:41 AM	#16
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,704	Re: PO has me PO'd [url=https://flic.kr/p/23TtUdk]20190130_101754 [url=https://flic.kr/p/23TusBP]20190130_103005 taking bolts out, 2 snapped sounds like they may break, so put studs in, will reinstall with lock tite, easy enough to put a torch up there to break bond if need be X is where the fitting goes, pretty big cavity in trans [url=https://flic.kr/p/SmNpbA]20190130_102840 backing plate, __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 01-30-2019 at 11:49 AM.

01-30-2019, 12:18 PM	#17
richard2717 Equal opportunity joke ofender Join Date: Oct 2011 Location: Eastern Shore of MD Posts: 10,091	Re: PO has me PO'd They look like McMaster packages __________________ Members I have met. Dually Jams, OlBlue60, ScottH, Tommyboy24, Dujobo, Warbucket, 2003 Silverado, Notsolo, my90k5, 6t727t2, Special-K ,Jack_71C10, tabarcus,72blazer_mud_bogger,pwdcougar,RSavage,EricSean,1Rippen6,invicta455,tennaragtop71,arks, Kendal,Bennett68C10, Perpendicular, Chainsawman, McGeesCustomMinis,ShortbedClayton,longblue72,6768chevylover,Tim71,Travisarmenta,Ol' Drippy,fleetmitch,georgieb51,Dave,bcnya2,Dadsburb https://paypal.me/6772GMtruckparts Most women like the strong, silent type… Fortunately for me, my wife prefers the out-of-shape, mouthy type.

01-30-2019, 09:38 PM	#19
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,704	Re: PO has me PO'd Whiskey :30 [url=https://flic.kr/p/SnefNo]20190130_203541 __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

02-01-2019, 11:00 AM	#20
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,704	Re: PO has me PO'd I like to use a live center when tapping, keeps the threads in proper alignment [url=https://flic.kr/p/2d8Ugv8]20190201_084147 while raceting tap Also, I like to use a rachet tap handle, pulling down on the quill , and rotate cw with tap [url=https://flic.kr/p/2d8Ugv8]20190201_084147 __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 02-01-2019 at 12:09 PM.



Register or Log In To remove these advertisements.

02-01-2019, 12:12 PM	#21
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,704	Re: PO has me PO'd [url=https://flic.kr/p/2d8Ww5e]20190201_093600 [url=https://flic.kr/p/QLqQc2]20190201_093518 __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

02-04-2019, 09:52 PM	#22
zicc1835 Senior Member Join Date: Mar 2011 Location: Hanover NJ Posts: 4,252	Re: PO has me PO'd Bottoms up..Jim __________________ Doc & Kim build http://67-72chevytrucks.com/vboard/s...d.php?t=722288 I am from the desert http://67-72chevytrucks.com/vboard/s...d.php?t=650332 basket case build SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=648557

02-06-2019, 05:17 PM	#23
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,704	Re: PO has me PO'd Thanks Jesse Decided to put on the seat backs, ss#10x 3/4" screws, I hate phillip head screws, ordered some square drive today from Mcmaster Carr I watch a show on Utube and he says to wax paint and rusty metal with tolette bowl wax(new) ring . So for 6.00 , I thought I would try it on my seat backs. Keeps the patina I was looking for, but protects the metal from further rust [url=https://flic.kr/p/2dvKjEu]20190206_085314 pics don't want to load __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 02-06-2019 at 05:34 PM.

02-06-2019, 07:13 PM	#24
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,704	Re: PO has me PO'd [url=https://flic.kr/p/2exajDJ]20190206_085341 __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

02-07-2019, 10:59 AM	#25
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,704	Re: PO has me PO'd [url=https://flic.kr/p/2dvSYJG]20190206_112501 It's in , very easy to match up studs with feet __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

Register or Log In To remove these advertisements.