1967 C10 Urban Retro - Page 7 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

VA72C10 · 03-23-2011, 08:07 PM

very nice!!!

spike38 · 03-23-2011, 08:10 PM

Looks sharp!!

Spike

Orangetonicclicc · 04-02-2011, 08:34 PM

Finally got my Red Oak Wood back and finally got some time to test fit it before staining. Made my marks for my holes that I'm going to have to drill. Not allthese aftermarket part hole are lining up. Going to have to drill some, on the front bed panels and the rear cross sills. The four coner boards are a pain. Also have my marks for my gas tank filler. hope fully I will have it complete by next week and installed.

**Hart_Rod** · 04-02-2011, 10:01 PM

Nice truck!

VA72C10 · 04-02-2011, 10:29 PM

bed looks good!!!

FRENCHBLUE72 · 04-03-2011, 09:24 AM

That bedwood is very nice red oak will look good for years..

Orangetonicclicc · 04-12-2011, 11:08 PM

The first step you see is the marine varnish that I applied to the underside of my wood floor. I let that dry over night. Next I sanded the top side with 320 grit sand paper. I then applied the wood conditioner to get a full and consistant stain. Leave on for 5 minutes wipe with cloth towel wrapped over a paint roller and wiped. Immediately I applied my red mahogany stain. Leaving on for 5-10 minutes. Then i wiped the excess.

Orangetonicclicc · 04-12-2011, 11:12 PM

I then let the wood dry for 24 hours re-sanded with 320 grit and stained again!

Orangetonicclicc · 04-12-2011, 11:15 PM

I also drilled my additional holes and had my gas tank filler hole done. I will give it a few days to dry and I will apply the mirror coat epoxy finish. (HOPEFULLY)

VA72C10 · 04-12-2011, 11:16 PM

Looking good!!!

Orangetonicclicc · 04-12-2011, 11:19 PM

Quote:

Originally Posted by VA72C10

Looking good!!!

Thanks!!!!!

spike38 · 04-13-2011, 03:47 AM

That's looking great!!!

Spike

Pop's C-10 · 04-13-2011, 07:03 AM

That came out nice

**67cheby** · 04-13-2011, 09:13 AM

That is looking great !!

Orangetonicclicc · 04-13-2011, 10:16 AM

Thanks guys! The most crucial step is coming up!! The dreaded Mirror Coat Clear Epoxy!!!! I will keep you posted! I actually video taped each step, I haven't learned how to attach videos yet... I may just post it on YouTube!!
Posted via Mobile Device

**67cheby** · 04-13-2011, 11:57 AM

most people neglect the step of doing the underneath side.... i think that is why you see alot of bad, bed wood...NICE WORK

Orangetonicclicc · 04-13-2011, 01:27 PM

Quote:

Originally Posted by 67cheby

most people neglect the step of doing the underneath side.... i think that is why you see alot of bad, bed wood...NICE WORK

Thanks, my whole purpose was and is to help the next guy when they get to this point. I've never did anything like this and so far so good. The Epoxy will be the tell all.
Posted via Mobile Device

fast50ranger · 04-13-2011, 02:22 PM

Very nice work

heeroyue2002 · 04-13-2011, 03:48 PM

Quote:

Originally Posted by Orangetonicclicc

Thanks guys! The most crucial step is coming up!! The dreaded Mirror Coat Clear Epoxy!!!! I will keep you posted! I actually video taped each step, I haven't learned how to attach videos yet... I may just post it on YouTube!!
Posted via Mobile Device

youtube will give you a link after u upload the video. click the one that says for message boards and paste it here and your good to go.

Orangetonicclicc · 04-18-2011, 09:44 PM

I wanted to wait and show you the finish job with it in my truck, but I didnt know when I was going to have time to install it. The pictures arent the best. First coat created fish eye, which at first had me concerned, The second coat fixed 95%. It came out great! The pictures dont do it justice!!

VA72C10 · 04-18-2011, 09:50 PM

Looks great!

Orangetonicclicc · 04-18-2011, 10:00 PM

Quote:

Originally Posted by VA72C10

Looks great!

Thanks I can always count on you to encourage me!!!!

spike38 · 04-19-2011, 12:13 AM

Man! That looks great!

Can't wait to get back on my truck

Spike

Orangetonicclicc · 04-19-2011, 12:23 AM

Quote:

Originally Posted by spike38

Man! That looks great!

Can't wait to get back on my truck

Spike

My rims will be here Wednesday!!! Here's afew more shots!!! Hey you will get it done. This has been a 5 year projectandI'm not expecting to be done until next summer. I'm taking a month off to finish a room in my house. (maybe)

tantrumpipeline · 04-19-2011, 12:48 PM

Looks great, that finish looks amazing, keep up the great work
Posted via Mobile Device

03-23-2011, 08:07 PM	#151
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: 1967 C10 Urban Retro very nice!!! __________________ Looking for a 67-72 swb or blazer project in or around VA.

03-23-2011, 08:10 PM	#152
spike38 Registered User Join Date: Jun 2010 Location: Leesburg GA Posts: 547	Re: 1967 C10 Urban Retro Looks sharp!! Spike __________________ 68 stepside http://67-72chevytrucks.com/vboard/s...0&goto=newpost

04-02-2011, 08:34 PM	#153
Orangetonicclicc Registered User Join Date: Feb 2011 Location: Oklahoma Posts: 744	Re: 1967 C10 Urban Retro Finally got my Red Oak Wood back and finally got some time to test fit it before staining. Made my marks for my holes that I'm going to have to drill. Not allthese aftermarket part hole are lining up. Going to have to drill some, on the front bed panels and the rear cross sills. The four coner boards are a pain. Also have my marks for my gas tank filler. hope fully I will have it complete by next week and installed. Attached Images __________________ http://67-72chevytrucks.com/vboard/s...ban+Retro:fro:

04-02-2011, 10:01 PM	#154
Hart_Rod ************* Join Date: Apr 2005 Location: Pensacola, FL Posts: 17,860	Re: 1967 C10 Urban Retro Nice truck! __________________ Rob - https://www.instagram.com/hart_rod_c10 As Iron Sharpens Iron, So One Man Sharpens Another. Proverbs 27:17 FOR SALE: DBW pedal bracket - http://67-72chevytrucks.com/vboard/s...d.php?t=651123 FOR SALE: Hood Brackets http://67-72chevytrucks.com/vboard/s...d.php?t=679945 1987 Silverado SWB - 34.5K original miles http://67-72chevytrucks.com/vboard/s...d.php?t=801834 1969 SuperBurb - http://67-72chevytrucks.com/vboard/s...d.php?t=200387 1968 Farm truck - http://67-72chevytrucks.com/vboard/s...d.php?t=358692 1968 SWB - http://67-72chevytrucks.com/vboard/s...d.php?t=551258 1948 Chevy - http://67-72chevytrucks.com/vboard/s...=122164&page=3

04-02-2011, 10:29 PM	#155
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: 1967 C10 Urban Retro bed looks good!!! __________________ Looking for a 67-72 swb or blazer project in or around VA.

04-03-2011, 09:24 AM	#156
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,608	Re: 1967 C10 Urban Retro That bedwood is very nice red oak will look good for years.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

04-12-2011, 11:08 PM	#157
Orangetonicclicc Registered User Join Date: Feb 2011 Location: Oklahoma Posts: 744	Re: 1967 C10 Urban Retro The first step you see is the marine varnish that I applied to the underside of my wood floor. I let that dry over night. Next I sanded the top side with 320 grit sand paper. I then applied the wood conditioner to get a full and consistant stain. Leave on for 5 minutes wipe with cloth towel wrapped over a paint roller and wiped. Immediately I applied my red mahogany stain. Leaving on for 5-10 minutes. Then i wiped the excess. Attached Images __________________ http://67-72chevytrucks.com/vboard/s...ban+Retro:fro:

04-12-2011, 11:12 PM	#158
Orangetonicclicc Registered User Join Date: Feb 2011 Location: Oklahoma Posts: 744	Re: 1967 C10 Urban Retro I then let the wood dry for 24 hours re-sanded with 320 grit and stained again! Attached Images __________________ http://67-72chevytrucks.com/vboard/s...ban+Retro:fro:

04-12-2011, 11:15 PM	#159
Orangetonicclicc Registered User Join Date: Feb 2011 Location: Oklahoma Posts: 744	Re: 1967 C10 Urban Retro I also drilled my additional holes and had my gas tank filler hole done. I will give it a few days to dry and I will apply the mirror coat epoxy finish. (HOPEFULLY) Attached Images __________________ http://67-72chevytrucks.com/vboard/s...ban+Retro:fro:

04-12-2011, 11:16 PM	#160
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: 1967 C10 Urban Retro Looking good!!! __________________ Looking for a 67-72 swb or blazer project in or around VA.

04-13-2011, 03:47 AM	#162
spike38 Registered User Join Date: Jun 2010 Location: Leesburg GA Posts: 547	Re: 1967 C10 Urban Retro That's looking great!!! Spike __________________ 68 stepside http://67-72chevytrucks.com/vboard/s...0&goto=newpost

04-13-2011, 07:03 AM	#163
Pop's C-10 Registered User Join Date: Jul 2010 Location: memphis Posts: 2,537	Re: 1967 C10 Urban Retro That came out nice __________________ 1981 C-10 (Pop's) 1978 Camaro 2006 Lacrosse

04-13-2011, 09:13 AM	#164
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: 1967 C10 Urban Retro That is looking great !! __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

04-13-2011, 10:16 AM	#165
Orangetonicclicc Registered User Join Date: Feb 2011 Location: Oklahoma Posts: 744	Re: 1967 C10 Urban Retro Thanks guys! The most crucial step is coming up!! The dreaded Mirror Coat Clear Epoxy!!!! I will keep you posted! I actually video taped each step, I haven't learned how to attach videos yet... I may just post it on YouTube!! Posted via Mobile Device __________________ http://67-72chevytrucks.com/vboard/s...ban+Retro:fro:

04-13-2011, 11:57 AM	#166
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: 1967 C10 Urban Retro most people neglect the step of doing the underneath side.... i think that is why you see alot of bad, bed wood...NICE WORK __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172



Register or Log In To remove these advertisements.

04-13-2011, 02:22 PM	#168
fast50ranger Registered User Join Date: Mar 2007 Location: Marbury, Alabama Posts: 195	Re: 1967 C10 Urban Retro Very nice work

04-18-2011, 09:44 PM	#170
Orangetonicclicc Registered User Join Date: Feb 2011 Location: Oklahoma Posts: 744	Re: 1967 C10 Urban Retro I wanted to wait and show you the finish job with it in my truck, but I didnt know when I was going to have time to install it. The pictures arent the best. First coat created fish eye, which at first had me concerned, The second coat fixed 95%. It came out great! The pictures dont do it justice!! Attached Images __________________ http://67-72chevytrucks.com/vboard/s...ban+Retro:fro:

04-18-2011, 09:50 PM	#171
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: 1967 C10 Urban Retro Looks great! __________________ Looking for a 67-72 swb or blazer project in or around VA.

04-19-2011, 12:13 AM	#173
spike38 Registered User Join Date: Jun 2010 Location: Leesburg GA Posts: 547	Re: 1967 C10 Urban Retro Man! That looks great! Can't wait to get back on my truck Spike __________________ 68 stepside http://67-72chevytrucks.com/vboard/s...0&goto=newpost

04-19-2011, 12:48 PM	#175
tantrumpipeline Master Procrastinator Join Date: Sep 2009 Location: Grande Prairie AB Canada Posts: 1,128	Re: 1967 C10 Urban Retro Looks great, that finish looks amazing, keep up the great work Posted via Mobile Device __________________ My Buildhttp://67-72chevytrucks.com/vboard/s...d.php?t=395506 20 Duramax tow pig 68 2wd short stepper project 77 2wd short fleet beater 52 short project

Register or Log In To remove these advertisements.