58 GMC Project - Page 7 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

CAL 58 GMC · 04-07-2006, 01:24 PM

Hey Jebb, I used Energy Suspension polyurethane on everything encluding motor & transmission mounts. Just make sure you know the year your clip is. I thought mine was a 1979 and then found out it was a 1980 after trying to install the bushings. They are not the same. Also I'm sending you a PM.

Jebb1978 · 04-07-2006, 01:48 PM

I noticed this may be a problem looking for parts yesterday. I remember the parts car well as it was a shame to carve it up. It was a 1975, has a heavy factory sway bar that I just may use. I have one more question for you. Sorry it never ends I know. As I was looking at the pics of your radiator support brackets I couldn't figure out where they are suppose to go on my truck. That's when I realized that you have square stock welded to the front of your subframe to make it straight like the stock frame and long enough to mount a bumper to. Look at where the steering box mounts to mine in comparison to yours. Yours looks so clean you really have to look to tell they did it. Can you measure from your A-arm to the tip of your frame for me so I can compare and lengthen mine as well?

CAL 58 GMC · 04-07-2006, 07:32 PM

Jebb, it’s never a problem asking question and anything I can do to help let me know, so ask away. I believe what was done on mine was the front of the original frame was cut off and welded back on the Camaro clip. I measured 23.75 inches from the upper A-arm mounting point. The best way to do it would be to put the fenders back on the radiator support and then put it back on the truck so you can see were the radiator support bracket needs to be welded on the frame. I hope that helps.

CAL 58 GMC · 04-07-2006, 07:55 PM

I had my truck towed to the muffler shop today and had the exhaust installed. Once I get the bed all done I will have the rest done with tips coming out from under the step on the bed.

dwcsr · 04-07-2006, 08:59 PM

You need to put a plexiglass floor in that truck. It a shame to cover up all that nice work

Jebb1978 · 04-07-2006, 09:35 PM

Wuff! Looks Hot!

Thanks for the info once again buddy!

CAL 58 GMC · 04-07-2006, 11:28 PM

Thanks again guys! And your welcome Jebb, glade to help.

55ChevyPU · 04-08-2006, 12:55 AM

Lookin sweet, I had the exhaust tips coming out from under the steps before I tore mine down, its definately going back together that way. Did you get those taillight buckets?

CAL 58 GMC · 04-08-2006, 09:59 AM

Thanks 55ChevyPU, I saw a 55 Chevy truck with them like that at a car show. They used the flat tips like the one's used on the newer Z-28 Camaro's. I haven’t got the taillight buckets yet, I've been real busy and just haven’t had the time to order them yet. Hows your coming along?

55ChevyPU · 04-08-2006, 10:24 PM

my trucks been sitting, ive needed a little time off. Today was my birthday so all I can say is windshield!

Igotachevyor2 · 04-08-2006, 11:53 PM

Quote:

Originally Posted by CAL 58 GMC

I had my truck towed to the muffler shop today and had the exhaust installed. Once I get the bed all done I will have the rest done with tips coming out from under the step on the bed.

your ride is coming together nice

CAL 58 GMC · 04-15-2006, 06:28 PM

Quote:

Originally Posted by Igotachevyor2

your ride is coming together nice

Thanks Igotachevyor2.

CAL 58 GMC · 04-15-2006, 06:35 PM

Hey 55ChevyPU, I know what you mean by needing a break. I've been working on my truck during the week and every weekend for the last 3 months and really needed a break myself. So Took this last week off and my wife and I went on a 7 day cruise to Mexico, which was a blast! Now it's time to get back to work on the truck again.

Jebb1978 · 04-16-2006, 03:52 AM

Welcome back!I trust you kids had fun. HAPPY EASTER!

55ChevyPU · 04-16-2006, 05:44 AM

Quote:

Originally Posted by CAL 58 GMC

Hey 55ChevyPU, I know what you mean by needing a break. I've been working on my truck during the week and every weekend for the last 3 months and really needed a break myself. So Took this last week off and my wife and I went on a 7 day cruise to Mexico, which was a blast! Now it's time to get back to work on the truck again.

Ive been busy lately between school, truck, and what not lately I guess it could still be considered a break though. Oh btw I wish I could go to mexico

.

Kabwe · 05-02-2006, 07:35 PM

Hey Cal55GMC,

I went by my brothers house the other day and he still has not developed those pics of the 55 Panel truck. But remember the chopper I was telling you about? I took pics of that and man it is a nice bike (you know I had to get my 55 210 in the pic also.lol)

If you want to see pics of the chopper go to my 55 210 site below

CAL 58 GMC · 05-02-2006, 08:50 PM

Hey kabwe,

I like the springer up front, it gives it classic chopper look. Is the bike a true ridget or a soft tail?

Jebb1978 · 05-03-2006, 07:52 PM

You doing okay Cali? Did you beat that flu bug? I haven't seen an update in a little bit. Hopeing it's just break time and all is well with you.

Southedisto · 05-03-2006, 07:56 PM

I dont know how I have missed this post this long, but that is a nice truck!

CAL 58 GMC · 05-03-2006, 08:44 PM

Thanks for the concern. The flu lasted 5 day's but it's finally gone. I have just been finishing up some small details on my truck, nothing really worth posting. This Saturday I am going to tow the chassis down to the body shop. The guy wants to mount the body on the frame and line up the gaps on the panels. It's an extra expense having to tow it down but it should be worth it.

The truck you picked up looks clean!

CAL 58 GMC · 05-03-2006, 08:59 PM

Thanks, Southedisto. It's been a lot of work and the folks here on the board have been really supportive. When a person such as you gives a thumbs up, it makes all of the hard work worth it! 55ChevyPU has a really nice project too. Jebb1978 is just getting started and has made some great progress in the short time since he started. Dwcsr has done some trick mods on his frame and suspension. Kabwe, Jebb1978, Igotachevyor2, 55Chevy and many others have given me some great inspiration along with making some good friends.

Thanks for checking out my project and keep coming back.

Jebb1978 · 05-03-2006, 11:42 PM

Glad to hear your doing well buddy! I can't wait to see that cab back on the frame. Thanks for the compliment, I really like that old rig. it was a lot of fun driving it out on the open road. I got people checking it out almost everytime I stopped.

CAL 58 GMC · 05-04-2006, 10:18 AM

It really sounds like you had a good road trip. Are the plans the same for the truck?

Jebb1978 · 05-04-2006, 11:19 AM

Quote:

Originally Posted by CAL 58 GMC

It really sounds like you had a good road trip. Are the plans the same for the truck?

Pretty much, I do have a bit more of a budget now that I sold my 78 so I am going to do more than I had planned to. Basically I want to do all the frame mods (as much like yours as I can

) and I am going to get all new suspension, brakes, driver train. I can afford to do more up grades than before but still won't be able to paint yet. That's what I am looking at.

Kabwe · 05-04-2006, 11:58 AM

58 GMC,

I glad you like the bike and it is a true ridget. I don't ride anymore I grew up and old enough now to where it hurts when I fall.lol

Can't wait to see that cab back on the frame.

04-07-2006, 01:24 PM	#151
CAL 58 GMC Senior Member Join Date: Jun 2005 Location: Clovis Ca. Posts: 3,311	Re: 58 GMC Project Hey Jebb, I used Energy Suspension polyurethane on everything encluding motor & transmission mounts. Just make sure you know the year your clip is. I thought mine was a 1979 and then found out it was a 1980 after trying to install the bushings. They are not the same. Also I'm sending you a PM.

04-07-2006, 01:48 PM	#152
Jebb1978 Senior Member Join Date: Aug 2005 Location: Mesa,Az Posts: 3,713	Re: 58 GMC Project I noticed this may be a problem looking for parts yesterday. I remember the parts car well as it was a shame to carve it up. It was a 1975, has a heavy factory sway bar that I just may use. I have one more question for you. Sorry it never ends I know. As I was looking at the pics of your radiator support brackets I couldn't figure out where they are suppose to go on my truck. That's when I realized that you have square stock welded to the front of your subframe to make it straight like the stock frame and long enough to mount a bumper to. Look at where the steering box mounts to mine in comparison to yours. Yours looks so clean you really have to look to tell they did it. Can you measure from your A-arm to the tip of your frame for me so I can compare and lengthen mine as well? __________________ 1959 GMC project

04-07-2006, 07:32 PM	#153
CAL 58 GMC Senior Member Join Date: Jun 2005 Location: Clovis Ca. Posts: 3,311	Re: 58 GMC Project Jebb, it’s never a problem asking question and anything I can do to help let me know, so ask away. I believe what was done on mine was the front of the original frame was cut off and welded back on the Camaro clip. I measured 23.75 inches from the upper A-arm mounting point. The best way to do it would be to put the fenders back on the radiator support and then put it back on the truck so you can see were the radiator support bracket needs to be welded on the frame. I hope that helps.

04-07-2006, 07:55 PM	#154
CAL 58 GMC Senior Member Join Date: Jun 2005 Location: Clovis Ca. Posts: 3,311	Re: 58 GMC Project I had my truck towed to the muffler shop today and had the exhaust installed. Once I get the bed all done I will have the rest done with tips coming out from under the step on the bed. Attached Images Last edited by CAL 58 GMC; 04-07-2006 at 07:57 PM.

04-07-2006, 08:59 PM	#155
dwcsr Hollister Road Co. Join Date: Apr 2005 Location: Houston Posts: 6,134	Re: 58 GMC Project You need to put a plexiglass floor in that truck. It a shame to cover up all that nice work Last edited by dwcsr; 04-07-2006 at 10:48 PM.

04-07-2006, 09:35 PM	#156
Jebb1978 Senior Member Join Date: Aug 2005 Location: Mesa,Az Posts: 3,713	Re: 58 GMC Project Wuff! Looks Hot! Thanks for the info once again buddy! __________________ 1959 GMC project Last edited by Jebb1978; 04-07-2006 at 09:35 PM.

04-07-2006, 11:28 PM	#157
CAL 58 GMC Senior Member Join Date: Jun 2005 Location: Clovis Ca. Posts: 3,311	Re: 58 GMC Project Thanks again guys! And your welcome Jebb, glade to help. Last edited by CAL 58 GMC; 04-07-2006 at 11:29 PM.

04-08-2006, 12:55 AM	#158
55ChevyPU Registered User Join Date: Jan 2006 Location: Riverside, California Posts: 282	Re: 58 GMC Project Lookin sweet, I had the exhaust tips coming out from under the steps before I tore mine down, its definately going back together that way. Did you get those taillight buckets? __________________ 55' Chevy Pickup Project Thread '55 chevy pics

04-08-2006, 09:59 AM	#159
CAL 58 GMC Senior Member Join Date: Jun 2005 Location: Clovis Ca. Posts: 3,311	Re: 58 GMC Project Thanks 55ChevyPU, I saw a 55 Chevy truck with them like that at a car show. They used the flat tips like the one's used on the newer Z-28 Camaro's. I haven’t got the taillight buckets yet, I've been real busy and just haven’t had the time to order them yet. Hows your coming along? Last edited by CAL 58 GMC; 04-08-2006 at 09:59 AM.

04-08-2006, 10:24 PM	#160
55ChevyPU Registered User Join Date: Jan 2006 Location: Riverside, California Posts: 282	Re: 58 GMC Project my trucks been sitting, ive needed a little time off. Today was my birthday so all I can say is windshield! __________________ 55' Chevy Pickup Project Thread '55 chevy pics

04-15-2006, 06:35 PM	#163
CAL 58 GMC Senior Member Join Date: Jun 2005 Location: Clovis Ca. Posts: 3,311	Re: 58 GMC Project Hey 55ChevyPU, I know what you mean by needing a break. I've been working on my truck during the week and every weekend for the last 3 months and really needed a break myself. So Took this last week off and my wife and I went on a 7 day cruise to Mexico, which was a blast! Now it's time to get back to work on the truck again.

04-16-2006, 03:52 AM	#164
Jebb1978 Senior Member Join Date: Aug 2005 Location: Mesa,Az Posts: 3,713	Re: 58 GMC Project Welcome back!I trust you kids had fun. HAPPY EASTER! __________________ 1959 GMC project Last edited by Jebb1978; 04-16-2006 at 04:33 AM.

05-02-2006, 07:35 PM	#166
Kabwe Certified Car Nut Join Date: Jan 2005 Location: Inglewood, California Posts: 3,118	Re: 58 GMC Project Hey Cal55GMC, I went by my brothers house the other day and he still has not developed those pics of the 55 Panel truck. But remember the chopper I was telling you about? I took pics of that and man it is a nice bike (you know I had to get my 55 210 in the pic also.lol) If you want to see pics of the chopper go to my 55 210 site below Last edited by Kabwe; 05-02-2006 at 07:36 PM.

05-02-2006, 08:50 PM	#167
CAL 58 GMC Senior Member Join Date: Jun 2005 Location: Clovis Ca. Posts: 3,311	Re: 58 GMC Project Hey kabwe, I like the springer up front, it gives it classic chopper look. Is the bike a true ridget or a soft tail? Last edited by CAL 58 GMC; 05-02-2006 at 08:50 PM.

05-03-2006, 07:52 PM	#168
Jebb1978 Senior Member Join Date: Aug 2005 Location: Mesa,Az Posts: 3,713	Re: 58 GMC Project You doing okay Cali? Did you beat that flu bug? I haven't seen an update in a little bit. Hopeing it's just break time and all is well with you. __________________ 1959 GMC project



Register or Log In To remove these advertisements.

05-03-2006, 07:56 PM	#169
Southedisto River life...... Join Date: Oct 2005 Location: Soldotna AK Posts: 1,078	Re: 58 GMC Project I dont know how I have missed this post this long, but that is a nice truck! __________________ I like wheelin in Dixie!

05-03-2006, 08:44 PM	#170
CAL 58 GMC Senior Member Join Date: Jun 2005 Location: Clovis Ca. Posts: 3,311	Re: 58 GMC Project Thanks for the concern. The flu lasted 5 day's but it's finally gone. I have just been finishing up some small details on my truck, nothing really worth posting. This Saturday I am going to tow the chassis down to the body shop. The guy wants to mount the body on the frame and line up the gaps on the panels. It's an extra expense having to tow it down but it should be worth it. The truck you picked up looks clean! Last edited by CAL 58 GMC; 05-03-2006 at 08:45 PM.

05-03-2006, 08:59 PM	#171
CAL 58 GMC Senior Member Join Date: Jun 2005 Location: Clovis Ca. Posts: 3,311	Re: 58 GMC Project Thanks, Southedisto. It's been a lot of work and the folks here on the board have been really supportive. When a person such as you gives a thumbs up, it makes all of the hard work worth it! 55ChevyPU has a really nice project too. Jebb1978 is just getting started and has made some great progress in the short time since he started. Dwcsr has done some trick mods on his frame and suspension. Kabwe, Jebb1978, Igotachevyor2, 55Chevy and many others have given me some great inspiration along with making some good friends. Thanks for checking out my project and keep coming back. Last edited by CAL 58 GMC; 05-03-2006 at 08:59 PM.

05-03-2006, 11:42 PM	#172
Jebb1978 Senior Member Join Date: Aug 2005 Location: Mesa,Az Posts: 3,713	Re: 58 GMC Project Glad to hear your doing well buddy! I can't wait to see that cab back on the frame. Thanks for the compliment, I really like that old rig. it was a lot of fun driving it out on the open road. I got people checking it out almost everytime I stopped. __________________ 1959 GMC project

05-04-2006, 10:18 AM	#173
CAL 58 GMC Senior Member Join Date: Jun 2005 Location: Clovis Ca. Posts: 3,311	Re: 58 GMC Project It really sounds like you had a good road trip. Are the plans the same for the truck? __________________ Classic Trucks Link http://www.classictrucks.com/feature...uck/index.html 1958 GMC.Project Build http://67-72chevytrucks.com/vboard/s...d.php?t=162816 1966 Chevelle Build http://67-72chevytrucks.com/vboard/s...d.php?t=443576 Video http://www.youtube.com/watch?v=prrNKo8F7Zw#GU5U2spHI_4

05-04-2006, 11:58 AM	#175
Kabwe Certified Car Nut Join Date: Jan 2005 Location: Inglewood, California Posts: 3,118	Re: 58 GMC Project 58 GMC, I glad you like the bike and it is a true ridget. I don't ride anymore I grew up and old enough now to where it hurts when I fall.lol Can't wait to see that cab back on the frame.

Register or Log In To remove these advertisements.