OR Parting out 72 GMC K20 4x4 350-TH350

[musclecarfreak]

Hey Tom, if you decide to cannibalize that 4 wheel drive next, keep me in mind! I still need an "intermediate" crossmember just ahead of the rear shock mounts, for my 72 long bed....to go with my other goodies I already got from you! Thanks in advance, Todd

[tll74]

bobvilla67, Front bump stops with brackets on 31.30 shipped.

John,
1. 4x4 V-8 Engine cross member.........................85
2. 4x4 Trans/Transfer cross member....................65
3. 4x4 Front spring/core support brackets ...........70
4. 4x4 Frame shackle mnt. for rear of front spring..50
5. 4x4 Front spring shackles...............................20.00?
6, 4x4 front shock mnts for frame.......................10
7. transfer case support mnt.............................45
8. Front bumper inner/outer brackets..................40.00 71-72 outers. I do not have the 70-down. Inners are the same as your 2wd
Not sure what shipping would be till packaged up. Probably about 75.00. How soon would you need these?

Todd, your up for this when I get it out. I haven't forgotten

Thanks, Tom

[bobvilla67]

I'll take them. Pm sent

[john@thepier]

Cancel the bumper brackets I'll take 1-7 then since I will be putting a 68 front end on this. I am in no hurry when you get to it is fine with me. Also I would prefer no slips with the torch, I can finish removing rivets to insure no extra cuts or torch damage. John

[VDB]

Would you happen to have another front leaf spring front mount? Going on a 68 K10
Thx!

[b.sharp]

Please let me know if you find the other pair of rear frame shock mounts. I need a set for my '64 K20. Thank you.

[tll74]

Originally Posted by bobvilla67

I'll take them. Pm sent

PM returned.

Originally Posted by john@thepier

Cancel the bumper brackets I'll take 1-7 then since I will be putting a 68 front end on this. I am in no hurry when you get to it is fine with me. Also I would prefer no slips with the torch, I can finish removing rivets to insure no extra cuts or torch damage. John

John, Ok..I'll do this truck next. It will be a week or so before I start. Don't worry I cut the rivets off the opposite side.

Originally Posted by VDB

Would you happen to have another front leaf spring front mount? Going on a 68 K10
Thx!

I don't have any 68 mounts. They are different from the 69-72.

Originally Posted by b.sharp

Please let me know if you find the other pair of rear frame shock mounts. I need a set for my '64 K20. Thank you.

The mounts on the next one I part out (71 K20) are available.

Thanks, Tom

[b.sharp]

please let me know and could you send a close up picture to cbmcad99@yahoo.com.
Thank you, I believe they are the same as mine but with a close up I could tell for sure.

[tll74]

pics for Randy.

[tll74]

Originally Posted by b.sharp

please let me know and could you send a close up picture to cbmcad99@yahoo.com.
Thank you, I believe they are the same as mine but with a close up I could tell for sure.

I'll get a pic once I get it in the shop. Thanks, Tom

[1972K20]

In case I didn't see it listed, do you have the locking hubs for the front axle?

[tll74]

Originally Posted by 1972K20

In case I didn't see it listed, do you have the locking hubs for the front axle?

Sorry no K20 locking hubs right now. They were robbed before I got the truck. Thanks, Tom

[MATT SHIELDS]

Tom, did you have a chance to look at those backing plates yet? Thanks for your help, Matt

[tll74]

Originally Posted by MATT SHIELDS

Tom, did you have a chance to look at those backing plates yet? Thanks for your help, Matt

Darn it...I totally spaced it. I do have them and they are off. I'll for sure get it done tomorrow. Thanks, Tom

[Rebo123]

I'm interested in the pair of rear/rear spring hangers. How much shipped to 15377 Pa. If you still have them. It's for my 72 K10 4x4. Thanks

[tll74]

Originally Posted by MATT SHIELDS

Tom, did you have a chance to look at those backing plates yet? Thanks for your help, Matt

Matt, They look good so far. I have them in my hot tank to clean them up nice for a better look.

Originally Posted by Rebo123

I'm interested in the pair of rear/rear spring hangers. How much shipped to 15377 Pa. If you still have them. It's for my 72 K10 4x4. Thanks

These are sold. I'm parting out another 4x4 next week that has them. 50.00 plus shipping. Shipping probably about 20.00.

Thanks, Tom

[MATT SHIELDS]

Originally Posted by tll74

Matt, They look good so far. I have them in my hot tank to clean them up nice for a better look.

These are sold. I'm parting out another 4x4 next week that has them. 50.00 plus shipping. Shipping probably about 20.00.

Thanks, Tom

Thanks Tom, let me know how the look when they are cleaned. If you could post some pics I would appreciate it. Thanks, Matt

[Rebo123]

Thanks Tom. If the rear/rear spring hangers are in good shape ill take them. I'm new to all of this, let me know what I need to do to get the ball rolling.

[tll74]

Originally Posted by MATT SHIELDS

Thanks Tom, let me know how the look when they are cleaned. If you could post some pics I would appreciate it. Thanks, Matt

I should be able to post pics tomorrow night.

Originally Posted by Rebo123

Thanks Tom. If the rear/rear spring hangers are in good shape ill take them. I'm new to all of this, let me know what I need to do to get the ball rolling.

They look to be fine. I will have a thread on that truck and reserve them for you or you could pay for them now and be done. It would be atleast a week before I can ship them. Send me a PM reguarding them.

Thanks, Tom

[lawest]

Tom, PM sent on a 4x4 sb fan shroud if you have one. Thanks, Larry

[Rebo123]

Tom, PM sent for the rear/rear leaf spring hangers. Thanks

[b.sharp]

Tom, If Matt passes on the backing plates. I am looking for a set and spindles to convert my '64 over to disk brakes.

[Douglas]

Do you happen to have any brake booster braces? I need the one thats about an inch wide and bolts to the firewall beneath the booster. It measures about 16" from end to end. The one for the 1/2 ton measures about 14 1/2 ".
I'm upgrading my 1/2 ton brakes and installing a larger booster and need the longer brace. I think the 3/4 and 1 ton have the longer ones. If so price to 71270. Thanks

[tll74]

pics for lawest. The shroud is a nice one with just minor fan rash as the pic shows. It has no cracks or any other damage. It has good color and looks nice. The pulleys are off a 72 350 with factory air.

[tll74]

Pics for MATT SHIELDS, I acid dipped and media blaslted the plates/shields. They have cracks where they are welded to the caliper support which was very common. I can weld them or let you. There is minor pitting from surface rust. 85.00 plus shipping. Thanks, Tom