1963 C-10 in NC

[1963c-10]

Originally Posted by 61K10

I always liked to break in an engine, first start up with mufflers, just in case the is a noise you can't here with open exhaust. have done it without also lol. I also do not run a thermostat and use just water and have a temp gauge hooked up. you probably know all of this stuff so happy brake-in.

I can finish the exhaust....would just set me back a day or so. I have all the dash complete, so full gauges hooked up. And didn't know about the thermostat. That's an easy fix too since its an o ring compression style. Thanks!!!

[61K10]

forgot, i always fill the block at the thermostat opening, then put the housing/hose back on. no air pockets in the block this way.

[1963c-10]

Eric showed up shortly after lunch. We got the brakes bled, still need some minor adjusting, but won't take much.

We also worked on the hydraulic clutch. Will need just a touch more adjusting there also. Slave still feels a little spongy, so still has some air in it. Doing all this around a big block and long tube headers is fun if you've never had the experience.

Later in the evening we switched gears to the engine. Got the covers swapped, #1 set to TDC, distributor pulled.....plenty of room for removal with the cap removed, engine primed, battery installed and of coarse it was dead, so took the battery out of Austins 63 and the oem starter just doesn't have enough to kick it over. Tried jumping off a truck and same result. By this time it was around 830, so we called it a night. I want to come in tonight and recheck that all grounds are good 1st, before I commit to a hi torque starter as it almost sounds like it doesn't have a good enough ground. Ran block to firewall grounds, battery to block and block to frame, so will pull grounds and make sure we have good contact.

Couple of pics of the vintage covers installed.

[TJ's Chevy]

Looks sweet!

[1963c-10]

Originally Posted by TJ's Chevy

Looks sweet!

Thanks TJ. Hoping I just have a bad ground issue and will have the engine resolved tonight. 2nd battery was good, but just got a click at the starter, so starter/selonoid either bad or bad grounds in my opinion.

[Pappyx3!]

Looks sharp!

[1963c-10]

Originally Posted by Pappyx3!

Looks sharp!

Thanks....be nice to turn her over now!!!

[Pappyx3!]

Originally Posted by 1963c-10

Thanks....be nice to turn her over now!!!

In the same boat with you Jon, went to start mine on Sunday, got to hear it run for about 2 mins, for the first time since Nov. Hang in there, I'm sure you'll be making motor music soon.

[Palf70Step]

Looking good. Hope it goes good and you hear the roar tonight.

[1963c-10]

Originally Posted by Palf70Step

Looking good. Hope it goes good and you hear the roar tonight.

Thanks and same here. Would love to hear her fire up tonight.

[TJ's Chevy]

Might need some more cranking amps to. Sometimes its the starter....sometimes its the battery not having enough guts to.

[1963c-10]

Originally Posted by TJ's Chevy

Might need some more cranking amps to. Sometimes its the starter....sometimes its the battery not having enough guts to.

1000cca battery is whats installed

[TJ's Chevy]

Originally Posted by 1963c-10

1000cca battery

That'll work.

[1963c-10]

Looking like powermaster 3635 Eric...only hi torque 3 bolt nose starter I found

http://www.jegs.com/i/Powermaster/713/3635/10002/-1

That means header removal on pass side and clutch inspection plates have to drop...love it

[1963c-10]

Will be looking at a heat shield also......

[1963c-10]

Went home and my new ground kit arrived. So, new grounds on both heads to firewall. Added a ground from the voltage regulator to the horn to radiator support and moved and cleaned the block to frame connection. It now runs directly to the block, not off a mount to the block.

[1963c-10]

Couple more

[Pappyx3!]

Ground straps look great! Where did you get them?

[1963c-10]

Originally Posted by Pappyx3!

Ground straps look great! Where did you get them?

Since your the electrician.....do the grounds look placed ok? Any more I should add?

[TJ's Chevy]

Fancy ground straps. My 292 in my 66 never had any for some reason...or any that I remember...its been awhile since I've seen it. haha. My 305 v6 has 1 on the driver's side valve cover to the fire wall. It didn't even matter weather I left it off or not. Not sure if I'm gonna use any on the new engine either...hope I don't need to.

[1963c-10]

Originally Posted by TJ's Chevy

Fancy ground straps. My 292 in my 66 never had any for some reason...or any that I remember...its been awhile since I've seen it. haha. My 305 v6 has 1 on the driver's side valve cover to the fire wall. It didn't even matter weather I left it off or not. Not sure if I'm gonna use any on the new engine either...hope I don't need to.

Don't know the pros or cons myself, but they are on and definitely can't hurt. As with most electrical things on these trucks there aren't enough grounds and they really aren't an eyesore if placed correct.

[Pappyx3!]

Originally Posted by 1963c-10

Since your the electrician.....do the grounds look placed ok? Any more I should add?

Again, not try to sound like a know it all, but I've been down this road with people many many times. Sent you that email... Suggest you don't add change or clean anything else. Let's do the testing, id the problem and make a "known" fix.

Pappyx4!

[1963c-10]

Originally Posted by Pappyx3!

Again, not try to sound like a know it all, but I've been down this road with people many many times. Sent you that email... Suggest you don't add change or clean anything else. Let's do the testing, id the problem and make a "known" fix.

Pappyx4!

Thanks. Email was received. Expecting rain for a majority of the day, but we'll see how the weather looks when I get home and see what I can get done.

[1963c-10]

And another big concern resolved.

Plenty of room on the tail shaft mount shifter. 1st 3 pics are in 1st gear and last is in reverse. Seat is still two notches from farthest position so still more room to go back. Relieved that we are good here. Do need to figure out a different shift boot as the hurst one will not work here.

[1963c-10]

And a couple of extra pics