Extreme Powder Coating '65 C-10 Shop Truck - Page 8 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

SCOTI · 01-18-2011, 03:41 PM

Quote:

Originally Posted by lucifer

Moser has them in stock ...same day shipping

Luc

I hope they've improved the fit of these. I purchased a set back in 2000 to use on my 68. The splines would not engage the spider gears. I tried filing them down slightly after discussion w/them w/no success. I ended up shipping the axles back to them w/one of my originals (so they could see the splines weren't messed up). I also taped (yes, slid on & taped in place) one of my spider gears so they could see what I was encountering.

I got the axles back a week or so later..... w/no spider gear. According to them, I didn't send a spider gear (remember, it was taped in place). So, approx 3wks after the original receipt of their axles, I had some that fit better, but now I had to source another spider gear since I had one missing.

I procured another spider gear only to still have issues getting the axles fully seated enough to install the c-clips. It seems the bearing races aren't machined in the exact correct area or the axle lengths are incorrect as there is wear on the differential pin that keeps the axles seated.

This was on a factory 6-lug, 1968 12-bolt housing. Like I said, hopefully things are better.

Scottshotrods · 01-18-2011, 03:52 PM

Moser does have them in stock and we have been useing them for the last 6 yrs have had no problems at all.They will stand behind there products 100%.If we can help you out let us know
Justin

kart34 · 01-18-2011, 04:56 PM

Almost there with all the custom fabrication by Wally's Speed Shop a division of Extreme Powder Coating

kart34 · 01-18-2011, 05:04 PM

***SNEAK PEAK*** This is our idea for floor pan - going big and exposing the PorterBuilt C-Notch!!!!

Alvin · 01-18-2011, 10:31 PM

Thanks man! I think I'll pick up a pair of the mufflers.

I am really happy with the look of the wheels... wish they offered a different width for the back, but it still works.

This truck you're building is pretty epic! I'm loving all the detail work going into it, keep it up!

kart34 · 01-19-2011, 12:00 AM

Thanks, We built a 67 Buick Wagon a few years ago with 145 powdercoated parts on it. It was a huge success for my job shop. The car was featured in Hot Rod and Car Craft magazine and has received several Good-Guys awards. SOOO we needed a new project !!!

Stay Tuned !!!!!!

kart34 · 01-19-2011, 05:15 PM

Rims came in from Delmo today and finishing up welds on bed mounts.

kvn1011 · 01-19-2011, 06:10 PM

Jesse is rockin on that bed!! looking good!!

Mad Rods · 01-20-2011, 12:08 AM

Coming along great kart.....man y'all work fast!!!
Posted via Mobile Device

67chevy1series · 01-20-2011, 12:11 AM

are those were the hub cap screws in those holes on the rim how ezactly does that work

kart34 · 01-20-2011, 08:12 AM

67 chevy, There are 5 clips that bolt on.

72BlckButy · 01-20-2011, 08:37 AM

Wow... you guys are not holding back on this; nice work!

kart34 · 01-20-2011, 05:34 PM

Been working hard today on getting the front end put together. Front fenders and grill surround.

72BlckButy · 01-20-2011, 05:37 PM

What's up with the repop fenders? Were the originals to rough?

kart34 · 01-20-2011, 05:46 PM

Got it all fitted and bolted on the frame. Hopefully this thing is ready to roll soon. Then we'll be powdercoating all the parts we possibly can!

kart34 · 01-20-2011, 06:36 PM

The re-pop fenders kinda suck ???? the originals were real ruff and rusty. We have a process with powdercoat to simulate the patina. Stay Tuned

Dirty Doug · 01-20-2011, 05:48 PM

Looks like the one guy is really busting a$$ .

Posted via Mobile Device

72BlckButy · 01-20-2011, 06:51 PM

Can't wait to see the PC process for simulating patina. Are you going to have a step by step process, or is it top secret?

kart34 · 01-20-2011, 10:22 PM

we will show the process stay tuned

Mechanic77 · 01-20-2011, 11:59 PM

Do you mind me asking....where did you get your fenders? They look like they fit pretty well

Dinos63 · 01-21-2011, 12:46 AM

nice work duudes!!!

Delmo · 01-21-2011, 01:30 AM

Man I can't wait to see those wheels stuffed under there.

kart34 · 01-21-2011, 08:10 AM

77, I purchased the fenders on E-Bay the fenders fit fairly well but they do not fit the grille / header panel at all. We may have to cut these up and us the front half of the stock GM fenders.

Mechanic77 · 01-21-2011, 10:12 AM

Quote:

Originally Posted by kart34

77, I purchased the fenders on E-Bay the fenders fit fairly well but they do not fit the grille / header panel at all. We may have to cut these up and us the front half of the stock GM fenders.

That's what I was afraid of....my fenders aren't too bad, but the main rust on them is on the fronts of them

Dirty Doug · 01-21-2011, 09:06 AM

Cutting the fenders in half and using the Gennie fronts will be cool! Matching the powder to patina will be a great trick. You can't let that secret totally out. The Technology challenged shops that bad mouth you and try to copy you may get a clue!!!
Just sayin...

01-18-2011, 03:52 PM	#2
Scottshotrods Registered User Join Date: Oct 2008 Location: oxnard ca Posts: 2,201	Re: Extreme Powder Coating '65 C-10 Shop Truck Moser does have them in stock and we have been useing them for the last 6 yrs have had no problems at all.They will stand behind there products 100%.If we can help you out let us know Justin

01-18-2011, 04:56 PM	#3
kart34 Registered User Join Date: Jul 2009 Location: Blooming Prairie, Minnesota Posts: 673	Re: Extreme Powder Coating '65 C-10 Shop Truck Almost there with all the custom fabrication by Wally's Speed Shop a division of Extreme Powder Coating Attached Images Last edited by kart34; 06-02-2013 at 06:45 PM.

01-18-2011, 05:04 PM	#4
kart34 Registered User Join Date: Jul 2009 Location: Blooming Prairie, Minnesota Posts: 673	Re: Extreme Powder Coating '65 C-10 Shop Truck *SNEAK PEAK* This is our idea for floor pan - going big and exposing the PorterBuilt C-Notch!!!! Attached Images Last edited by kart34; 01-18-2011 at 09:47 PM.

01-18-2011, 10:31 PM	#5
Alvin Never Done? Join Date: May 2000 Location: Ohio Posts: 1,435	Re: Extreme Powder Coating '65 C-10 Shop Truck Thanks man! I think I'll pick up a pair of the mufflers. I am really happy with the look of the wheels... wish they offered a different width for the back, but it still works. This truck you're building is pretty epic! I'm loving all the detail work going into it, keep it up! __________________ Ethel - The Legend Continues... Ethel has been sold.

01-19-2011, 12:00 AM	#6
kart34 Registered User Join Date: Jul 2009 Location: Blooming Prairie, Minnesota Posts: 673	Re: Extreme Powder Coating '65 C-10 Shop Truck Thanks, We built a 67 Buick Wagon a few years ago with 145 powdercoated parts on it. It was a huge success for my job shop. The car was featured in Hot Rod and Car Craft magazine and has received several Good-Guys awards. SOOO we needed a new project !!! Stay Tuned !!!!!! Last edited by Liz; 02-18-2011 at 09:32 PM. Reason: advertising

01-19-2011, 05:15 PM	#7
kart34 Registered User Join Date: Jul 2009 Location: Blooming Prairie, Minnesota Posts: 673	Re: Extreme Powder Coating '65 C-10 Shop Truck Rims came in from Delmo today and finishing up welds on bed mounts. Attached Images Last edited by kart34; 01-19-2011 at 08:22 PM.

01-19-2011, 06:10 PM	#8
kvn1011 Kvn1011 Join Date: May 2009 Location: kankakee il Posts: 560	Re: Extreme Powder Coating '65 C-10 Shop Truck Jesse is rockin on that bed!! looking good!!

01-20-2011, 12:08 AM	#9
Mad Rods Chevy Only Tx Join Date: May 2009 Location: Pecos,Tx Posts: 1,061	Re: Extreme Powder Coating '65 C-10 Shop Truck Coming along great kart.....man y'all work fast!!! Posted via Mobile Device __________________ Chevy Only Tx.........

01-20-2011, 12:11 AM	#10
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: Extreme Powder Coating '65 C-10 Shop Truck are those were the hub cap screws in those holes on the rim how ezactly does that work

01-20-2011, 08:12 AM	#11
kart34 Registered User Join Date: Jul 2009 Location: Blooming Prairie, Minnesota Posts: 673	Re: Extreme Powder Coating '65 C-10 Shop Truck 67 chevy, There are 5 clips that bolt on. Last edited by kart34; 01-20-2011 at 08:39 AM.

01-20-2011, 08:37 AM	#12
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: Extreme Powder Coating '65 C-10 Shop Truck Wow... you guys are not holding back on this; nice work! __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package)

01-20-2011, 05:34 PM	#13
kart34 Registered User Join Date: Jul 2009 Location: Blooming Prairie, Minnesota Posts: 673	Re: Extreme Powder Coating '65 C-10 Shop Truck Been working hard today on getting the front end put together. Front fenders and grill surround. Attached Images

01-20-2011, 05:37 PM	#14
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: Extreme Powder Coating '65 C-10 Shop Truck What's up with the repop fenders? Were the originals to rough? __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package)

01-20-2011, 05:46 PM	#15
kart34 Registered User Join Date: Jul 2009 Location: Blooming Prairie, Minnesota Posts: 673	Re: Extreme Powder Coating '65 C-10 Shop Truck Got it all fitted and bolted on the frame. Hopefully this thing is ready to roll soon. Then we'll be powdercoating all the parts we possibly can! Attached Images

01-20-2011, 06:36 PM	#16
kart34 Registered User Join Date: Jul 2009 Location: Blooming Prairie, Minnesota Posts: 673	Re: Extreme Powder Coating '65 C-10 Shop Truck The re-pop fenders kinda suck ???? the originals were real ruff and rusty. We have a process with powdercoat to simulate the patina. Stay Tuned Last edited by Liz; 02-18-2011 at 09:32 PM. Reason: advertising



Register or Log In To remove these advertisements.

01-20-2011, 05:48 PM	#17
Dirty Doug Registered User Join Date: Oct 2010 Location: Twin Cities, Mn. Posts: 114	Re: Extreme Powder Coating '65 C-10 Shop Truck Looks like the one guy is really busting a$$ . Posted via Mobile Device Last edited by Dirty Doug; 01-21-2011 at 08:57 AM.

01-20-2011, 06:51 PM	#18
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: Extreme Powder Coating '65 C-10 Shop Truck Can't wait to see the PC process for simulating patina. Are you going to have a step by step process, or is it top secret? __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package)

01-20-2011, 10:22 PM	#19
kart34 Registered User Join Date: Jul 2009 Location: Blooming Prairie, Minnesota Posts: 673	Re: Extreme Powder Coating '65 C-10 Shop Truck we will show the process stay tuned

01-20-2011, 11:59 PM	#20
Mechanic77 Registered User Join Date: Nov 2010 Location: Burrton, KS Posts: 215	Re: Extreme Powder Coating '65 C-10 Shop Truck Do you mind me asking....where did you get your fenders? They look like they fit pretty well __________________ Pro Touring 1964 C10-Under Construction http://67-72chevytrucks.com/vboard/s...d.php?t=441627 Project '65 Short Step Daily Driver http://67-72chevytrucks.com/vboard/s...d.php?t=661948

01-21-2011, 12:46 AM	#21
Dinos63 chevy only Join Date: Sep 2006 Location: Phoenix, AZ Posts: 6,619	Re: Extreme Powder Coating '65 C-10 Shop Truck nice work duudes!!! __________________ CHEVY ONLY... Nothin Else !

01-21-2011, 01:30 AM	#22
Delmo Registered User Join Date: Feb 2003 Location: Burbank CA Posts: 1,226	Re: Extreme Powder Coating '65 C-10 Shop Truck Man I can't wait to see those wheels stuffed under there.

01-21-2011, 08:10 AM	#23
kart34 Registered User Join Date: Jul 2009 Location: Blooming Prairie, Minnesota Posts: 673	Re: Extreme Powder Coating '65 C-10 Shop Truck 77, I purchased the fenders on E-Bay the fenders fit fairly well but they do not fit the grille / header panel at all. We may have to cut these up and us the front half of the stock GM fenders.

01-21-2011, 09:06 AM	#25
Dirty Doug Registered User Join Date: Oct 2010 Location: Twin Cities, Mn. Posts: 114	Re: Extreme Powder Coating '65 C-10 Shop Truck Cutting the fenders in half and using the Gennie fronts will be cool! Matching the powder to patina will be a great trick. You can't let that secret totally out. The Technology challenged shops that bad mouth you and try to copy you may get a clue!!! Just sayin...

Register or Log In To remove these advertisements.