![]() |
![]() |
#176 |
Registered User
Join Date: Jul 2010
Location: Windsor CA
Posts: 154
|
Re: Lss3
Thanks-
The engine was a pull out from a 2010 Camaro with 4 miles. An LS7 swap was done. The accessories are CTSV ones. No notching was done, but the fittings are tricky. I bought some parts that almost work. They will require a bit of machining. |
![]() |
![]() |
![]() |
#177 |
Registered User
Join Date: Apr 2015
Location: Hockley, TX
Posts: 24
|
Re: Lss3
Thanks. I have a line on a 2010 ls3 with 14,000 on the clock. Going to use a T-56 behind it. I was thinking of using the vintage air front runner. Did you finish your wiring harness? I've heard that Painless makes a nice one that is easy to deal with. Any advice is greatly appreciated.
|
![]() |
![]() |
![]() |
#178 |
Registered User
Join Date: Jul 2010
Location: Windsor CA
Posts: 154
|
Re: Lss3
I’m using the GMPP 19201861 controller kit. It includes the wiring harness, computer and many of the needed sensors. I’ve laid it on the engine. To dress it nicely, I will need to take all the tape and split tubing off.
|
![]() |
![]() |
![]() |
#179 |
Registered User
Join Date: Jul 2010
Location: Windsor CA
Posts: 154
|
Re: Lss3
I scored today. At work, we had an action of excess equipment to benefit the United Way. I came home with this killer TIG welder. I hope it will improve the sheet metal work. It will likely divert my attention from the truck to get the welder set up.
|
![]() |
![]() |
![]() |
#180 |
Registered User
Join Date: Apr 2015
Location: Hockley, TX
Posts: 24
|
Re: Lss3
Sweeeet! I'm so tired of grinding my crappy mig welds. Good luck on learning your new machine
|
![]() |
![]() |
![]() |
#181 |
Senior Member
![]() Join Date: May 2014
Location: Vancouver, BC
Posts: 555
|
Re: Lss3
What are you going to wrap your wires with.? I saw someone else using some expensive stuff but it sure looked good. Can't remember who's thread.
__________________
Kitsbeach (Ken) 1967 C10 LWB (now SWB) Fleetside 6cyl Saginaw three-on-the-tree "No Frills" 1980 C20 Long to short & static drop "Square One" |
![]() |
![]() |
![]() |
#182 |
Registered User
Join Date: Jul 2010
Location: Windsor CA
Posts: 154
|
Re: Lss3
I am using Power Braid from Painless Performance.
|
![]() |
![]() |
![]() |
#183 |
Registered User
Join Date: Jul 2010
Location: Windsor CA
Posts: 154
|
Re: Lss3
There’s been a little progress to the to the brake lines. My Eastwood flaring tool is working great double flaring the stainless steel lines.
|
![]() |
![]() |
![]() |
#184 |
Registered User
Join Date: Jul 2010
Location: Windsor CA
Posts: 154
|
Re: Lss3
Well it’s been a while. As I suspected, the new welder diverted me for a while. I had to get Argon for it and resolve a flow meter issue. I ended up rebuilding it. Now the system is working. Now to learn how to use it.
I have spent a lot of time, staring at the chassis, trying to figure out how to run the brake and fuel lines, the emergency brake cables and where to hang the battery. It is much easier to look at it than work on it. I did receive one wheel. It is a 17X9 Rally from Year One. It passed the first test: Does it clear the brake caliper? Now I need to assemble more of the truck to see if it clears everything else. I only bought one just in case there is a problem. |
![]() |
![]() |
![]() |
#185 |
Registered User
Join Date: Jul 2010
Location: Windsor CA
Posts: 154
|
Re: Lss3
I think I finally have the emergency brake routing figured out.
|
![]() |
![]() |
![]() |
#186 |
Registered User
Join Date: Jul 2010
Location: Windsor CA
Posts: 154
|
Re: Lss3
Several months ago I got a 25’ coil of 3/8” stainless steel tubing to use for fuel lines. I didn’t spring for the $90 tubing straightener from Eastwood. A tool that only works on one size material that would likely only be used once. I tried hand straightening. That really screwed it up. I also tried several wooden jigs clamped together with C clamps. This worked a little better, but not good enough. Lots of ripples remained. Today I used the machine shop at work to make a base plate out of aluminum. Home Depot had some wheels used on patio doors. It is a bit tricky to adjust, but the tubing ended up straight. Now there is no more excuse for not completing the fuel lines.
|
![]() |
![]() |
![]() |
#187 |
Registered User
Join Date: Dec 2011
Location: Earth, NJ
Posts: 479
|
Re: Lss3
Thats what I did, works great. I put 5 rollers on though
|
![]() |
![]() |
![]() |
#188 |
Registered User
Join Date: Oct 2013
Location: Bremerton, WA
Posts: 287
|
Re: Lss3
Nice work. Coming along great
__________________
1972 Chevrolet swb fleet side. - SOLD 2018 Toyota Tacoma but hunting for another C10 Link to my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=607303 Instagram: https://www.instagram.com/72c10shortbox/?hl=en |
![]() |
![]() |
![]() |
#189 |
Registered User
Join Date: Jul 2010
Location: Windsor CA
Posts: 154
|
Re: Lss3
Running the fuel and brake lines has really stumped me. I want to run them in a single length inside the frame. I couldn’t figure out how to get the right shape. On Monday, I decided to make a layout table that I could draw a full size template of the frame on it. I taped a laser level to the bottom of the frame so I could measure the different heights of it. It will take a bit more time to finish the drawing and start bending tubing.
|
![]() |
![]() |
![]() |
#190 |
Still Learning
Join Date: Jul 2009
Location: Central Oklahoma
Posts: 10,108
|
Re: Lss3
Nice progress on your truck. Just keeps getting nicer!
|
![]() |
![]() |
![]() |
#191 |
Registered User
Join Date: Jul 2010
Location: Windsor CA
Posts: 154
|
Re: Lss3
I finished measuring the frame and drawing it on the layout table, then drawing the fuel line. I did a test bend with aluminum tubing and tried to weave it into the frame. No luck. The tube got mangled. Maybe the stainless tubing would have sprung back, but I decided not to chance it. I added a bulkhead fitting to the cross member in front of the fuel tank. This way the fuel line can be split in two. There will be fewer obstacles for each piece to work around.
I got a couple of parts to start my intake system, both from Spectre Performance. The flexible elbow is part number 9785 and the mass air flow sensor 9718. I still need to figure out an air cleaner and housing. It needs to pull cool air from in front of the radiator. |
![]() |
![]() |
![]() |
#192 | |
*************
![]() Join Date: Apr 2005
Location: Pensacola, FL
Posts: 17,846
|
Re: Lss3
Quote:
__________________
Rob - https://www.instagram.com/hart_rod_c10 As Iron Sharpens Iron, So One Man Sharpens Another. Proverbs 27:17 FOR SALE: DBW pedal bracket - http://67-72chevytrucks.com/vboard/s...d.php?t=651123 FOR SALE: Hood Brackets http://67-72chevytrucks.com/vboard/s...d.php?t=679945 1987 Silverado SWB - 34.5K original miles http://67-72chevytrucks.com/vboard/s...d.php?t=801834 1969 SuperBurb - http://67-72chevytrucks.com/vboard/s...d.php?t=200387 1968 Farm truck - http://67-72chevytrucks.com/vboard/s...d.php?t=358692 1968 SWB - http://67-72chevytrucks.com/vboard/s...d.php?t=551258 1948 Chevy - http://67-72chevytrucks.com/vboard/s...=122164&page=3 |
|
![]() |
![]() |
![]() |
#194 |
Registered User
Join Date: Jul 2010
Location: Windsor CA
Posts: 154
|
Re: Lss3
Rob-
That’s a nice setup. I have been considering several commercial parts like the 9831 from Spectre performance or the 17-2519 from DoghouseRepair.com. The Spectre unit would require some more fittings to connect to the radiator support. The doghouse part is nice. I like the large filter, but the filter is not commonly available. I think the setup was designed for dune buggies. The other possibility is making my own housing for a standard filter. The Fram CA6818 looks interesting. It has a 4” ID, 8.5” OD and is 12.38” long. Since you’ve been running your system for a while, is there anything you would do differently? |
![]() |
![]() |
![]() |
#195 |
Registered User
Join Date: Jul 2010
Location: Windsor CA
Posts: 154
|
Re: Lss3
Well I finally got the stainless fuel line bent. What a pain. It is in the chassis and ready to have clamps installed. Once that is done it is time to test the fuel system. Hopefully there will be no leaks.
|
![]() |
![]() |
![]() |
#196 |
Registered User
Join Date: Jul 2010
Location: Windsor CA
Posts: 154
|
Re: Lss3
Look what my truck got for Christmas:
|
![]() |
![]() |
![]() |
#197 |
Registered User
Join Date: Jul 2010
Location: Windsor CA
Posts: 154
|
Re: Lss3
Another piece I’ve been working on are the turn buckle adjustments for the rear sway bar. He ones that came from Hotchkis were intended for a 6 inch drop. Since I am only doing 4, the turn buckles needed to be longer. I made them out of ¾” aluminum, 8.5” long. The ends are drilled and taped. To make the turn buckle work, one needs to have left hand threads. Flats were milled to have a place for a wrench to adjust them.
|
![]() |
![]() |
![]() |
#198 |
Registered User
Join Date: Jul 2010
Location: Windsor CA
Posts: 154
|
Re: Lss3
I did some mock up work with the new AC. I don’t plan on mounting it the way Vintage Air recommends. I want it to be more hotrod like. This means it will be neater. The firewall will be smoothed. I’d also like to get a deeper glove compartment than the stock VA allows. As can be seen in the second photo, the bracket spaces the evaporator pretty far away from the firewall. It should be able to move an inch or so closer. This will require the hoses to be moved further to the passenger side, something like the third picture.
|
![]() |
![]() |
![]() |
#199 |
Registered User
Join Date: Jul 2010
Location: Windsor CA
Posts: 154
|
Re: Lss3
Been thinking about body work and paint. The sheet metal is in very good condition with the exception of the rusted out holes shown below. Looks like I'll get the chance to use that TIG welder. The rocker panels and cab corners appear to be good. I hope to abrasive blast and use an inspection camera to verify they are really solid.
|
![]() |
![]() |
![]() |
#200 |
Registered User
Join Date: Oct 2007
Location: Spanaway
Posts: 8,451
|
Re: Lss3
Nice work on the cold air box, most people just route the air cleaner into the corner and call it good. The truck is looking sweet!
__________________
Mike. Swamp Rat build thread : http://67-72chevytrucks.com/vboard/s...d.php?t=595019 72 3/4T 4X4 4" BDS Lift 33" BFG's Last edited by swamp rat; 01-11-2016 at 12:00 AM. |
![]() |
![]() |
![]() |
Bookmarks |
|
|