What did you do to your truck today! - Page 80 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ChopperDr · 04-02-2011, 09:01 AM

From Fordparts.com picked up at my local dealer for $27.91. Look up parts for a 1995 Bronco.
Part Name: Bumper Valance Panel
Part Number: 17626
Part Description: Black (Front)

I used some self tapping screws on the lower edge of the front fenders and two brackets I bent up to secure it to the bottom of the frame rails. I'll get more pics if it ever stops raining.

Chopster

**70cst** · 04-02-2011, 09:36 AM

Today fine69 will be picking up the Circuit Rider and hauling it back to his shop and fix the "leaks"...then once it is mechanically sound I will drive it down to the body shop and let Curt wrap up a few details that need to be finished. Then the Circuit Rider will be ready to prowl the streets in all her glory.

The next step is to buy a set of 15x7 TT II's for the front and also a tonneau covers for the bed.

*project 67 sub* · 04-02-2011, 08:17 PM

Quote:

Originally Posted by ChopperDr

From Fordparts.com picked up at my local dealer for $27.91. Look up parts for a 1995 Bronco.
Part Name: Bumper Valance Panel
Part Number: 17626
Part Description: Black (Front)

I used some self tapping screws on the lower edge of the front fenders and two brackets I bent up to secure it to the bottom of the frame rails. I'll get more pics if it ever stops raining.

Chopster

ok sweet thanks

BadaSs_Cal · 04-01-2011, 07:03 PM

got the vent windows out and side glass... Called around for pricing to have the cab blasted. Kinda was trying to avoid going this far...but "might as well"

50bomb · 04-02-2011, 10:29 AM

Dropped in my 350/th350 yesterday..Use to be a inline 6 with 3 speed Od. Now to figure why my 2 piece drivehaft is to short...And about 2 inches from even touchin the trans. Any ideas?

60ratrod · 04-02-2011, 12:05 PM

the l6 mounts sit further back on the crossmember than the 2wd v8 mounts. you can a) move the engine back to the rear holes, where the l6 was sitting b) get a th350 with the 9" tail housing c) lengthen the drive shaft

Frkypunk70 · 04-02-2011, 04:00 PM

Took my CCP 3" drop springs out. Replaced them with factory ones with full coil cut. Put moog poly sway bar frame mounts in. Finally put my woodgrain trim piece for the tailgate on. Prepped and painted new radiator to replace the completely wrong one that's in the truck. Decided to take the old girl for a ride to get beer and tryout new suspension. Rides great now but needs drop shocks. The beer is good too

Posted via Mobile Device

**70cst** · 04-02-2011, 04:54 PM

Bye Bye

FRENCHBLUE72 · 04-02-2011, 05:02 PM

Quote:

Originally Posted by 70cst

Bye Bye

What the hell did I miss????? did you sell your truck????

**70cst** · 04-02-2011, 05:06 PM

Quote:

Originally Posted by FRENCHBLUE72

What the hell did I miss????? did you sell your truck????

Fine69 is taking it to his shop to do some work on the mechanics...then it will be ready to prowl the road.

FRENCHBLUE72 · 04-02-2011, 04:30 PM

Went and bought a battery and fuel.... Hope to have her out of the garage this evening..

Garthc20 · 04-02-2011, 04:33 PM

new bowtie today

FRENCHBLUE72 · 04-02-2011, 06:01 PM

Sweet deal I recognized fine69's roll back and had hoped you did not have to sell her at least she is in good hands..

nickp51chevy · 04-03-2011, 01:08 AM

Replaced the ball joints on the right front. Only took all day to get that done....didn't help that we were also working on my brother in law's truck also, and the 10 or more runs to the parts store for tools and/or other parts. But it's done now, and the wheel is nice a solid once again.

RossRinSD · 04-03-2011, 02:00 AM

Hai guys, haven't been on in a while. Nice to see everybody is making some progress.

I was able to finally install the window my girlfriend got me for Christmas, a tinted sliding rear window.

60ratrod · 04-03-2011, 03:39 AM

finished turning my 72 into a flintstonesmobile. the driver's floor pan was pretty much toast, along with my driver's front cab support/mount. as you can see its no longer connected to the rocker. but at least the inner rocker panel is in great shape so i don't have to worry about patching/replacing it. but now i get to fight with the original cab mount bolt that goes under the driver's feet so i can get the cab support/mount off and replaced. my question is do i need the plate that sat under the floor board where the bolt goes through for the mount? if not then i'm getting rid of it. if i do then i'm gonna make a new one. sorry for the hazy photo. friggen cell phones.

orange70350 · 04-03-2011, 07:56 PM

i got the clip bed and cab removed

pulltilbroke · 04-03-2011, 03:29 AM

Got the motor and tranny pulled and started swapping a few things over to the 292!!

k7elh · 04-03-2011, 09:06 PM

I watched it continue to rust.

lil hoodlum · 04-03-2011, 10:01 PM

Installed new dash pad from LMC. Dashpad was actually boxed and is from DashesDirect. Installed hood letters "chevrolet" and installed new drop shocks (Monroes #5752, 8.625" compressed/ 12.75" extended)

Keith

*72chevy383* · 04-23-2011, 09:42 PM

Quote:

Originally Posted by lil hoodlum

Installed new dash pad from LMC. Dashpad was actually boxed and is from DashesDirect. Installed hood letters "chevrolet" and installed new drop shocks (Monroes #5752, 8.625" compressed/ 12.75" extended)

Keith

Wondering what drop you have on the front, I'm looking for some shocks for my 71 build, I have 2.5 drop spindles and stock coils.

Tom

bucketObolts · 04-03-2011, 10:52 PM

Well today I spent more time ordering parts than doing actual work but I did manage pull 4 of my air valves out and all wiring out for replacement. Pulled the rear bags off since they are dry rotted and debated whether to change out the fronts too. Didnt have much more to do since im still waiting for a new gun for my MIG, plus i really didnt feel like working on the Painless kit so I used the time to accomplish some much needed toolbox re-organization and tool cleaning.

sjarrett71 · 04-03-2011, 10:53 PM

I got my manual trans removed and my auto trans installed. It is so much funner to drive now!

6772owner · 04-04-2011, 09:19 AM

I installed my Autometer water temp and trans temp in the factory cluster. I put the trans temp in place of the "amp" gauge for now, they never work anyway.

I also recalibrated my governor again (7th try) and think I might have a decent calibration for the first time.

I also installed a new Kenwood Excelon CD player, OE fog lamps and did an oil change on my Camaro... then went out to the Golden cruise night, great weekend.

Reed's72 · 04-04-2011, 10:36 PM

gave into my 14 year old and let her drive around the block,

04-02-2011, 09:01 AM	#1
ChopperDr Registered User Join Date: Feb 2008 Location: WA Posts: 189	Re: What did you do to your truck today! From Fordparts.com picked up at my local dealer for $27.91. Look up parts for a 1995 Bronco. Part Name: Bumper Valance Panel Part Number: 17626 Part Description: Black (Front) I used some self tapping screws on the lower edge of the front fenders and two brackets I bent up to secure it to the bottom of the frame rails. I'll get more pics if it ever stops raining. Chopster

04-02-2011, 09:36 AM	#2
70cst Senior Member Join Date: Feb 2001 Location: New Madison, Ohio Posts: 21,375	Re: What did you do to your truck today! Today fine69 will be picking up the Circuit Rider and hauling it back to his shop and fix the "leaks"...then once it is mechanically sound I will drive it down to the body shop and let Curt wrap up a few details that need to be finished. Then the Circuit Rider will be ready to prowl the streets in all her glory. The next step is to buy a set of 15x7 TT II's for the front and also a tonneau covers for the bed. __________________ A husband can be right...or...A husband can be happy. 67-72 Chevy and GMC Trucks...The Classic Truck for the Classic Folk. 1970 CST Two tone green, 402BB, 400 Automatic, Tach, Buckets, AC, AM-FM, Tilt, GM CB, GM 8 Tract, LWB, etc JOHN 17:3...The better side of "LIFE" Remember: Everyday is a good day...Some are just gooder! Last edited by 70cst; 04-02-2011 at 09:41 AM.

04-01-2011, 07:03 PM	#4
BadaSs_Cal Registered User Join Date: Feb 2010 Location: Walnut Grove, Ca Posts: 216	Re: What did you do to your truck today! got the vent windows out and side glass... Called around for pricing to have the cab blasted. Kinda was trying to avoid going this far...but "might as well" __________________ 66 Gmc 1 ton. Long Step 351e V6 69 1/2 CHEVROLET (now a shortbed) LONGBED!:devil 61 Shortbed Fleetside 1/2 ton.. in progress Next a 50-53! MY BUILD THREAD http://67-72chevytrucks.com/vboard/s...d.php?t=447926

04-02-2011, 12:05 PM	#6
60ratrod yes, i do Join Date: Jun 2007 Location: Spokane, wa Posts: 2,734	Re: What did you do to your truck today! the l6 mounts sit further back on the crossmember than the 2wd v8 mounts. you can a) move the engine back to the rear holes, where the l6 was sitting b) get a th350 with the 9" tail housing c) lengthen the drive shaft __________________ ERROR 404....... SNAPPY COMEBACK NOT FOUND _______________________________________________________________________________________________ -60 Chevy C10, dead 350/good th350 combo, sitting on a 76 c10 blazer frame, built from 11 different vehicles "the abomination" -07 gmt900 silverado 1500 lt xcab z71, granite blue -81 suzuki gs650g "shelah"- current project -81 kz1000m1 csr "sarge" -next project (just beautification) -07 kawasaki vulcan classic vn900

04-02-2011, 04:00 PM	#7
Frkypunk70 Registered User Join Date: Mar 2010 Location: Scranton,Pa Posts: 423	Re: What did you do to your truck today! Took my CCP 3" drop springs out. Replaced them with factory ones with full coil cut. Put moog poly sway bar frame mounts in. Finally put my woodgrain trim piece for the tailgate on. Prepped and painted new radiator to replace the completely wrong one that's in the truck. Decided to take the old girl for a ride to get beer and tryout new suspension. Rides great now but needs drop shocks. The beer is good too Posted via Mobile Device __________________ "When I die, I want to go peacefully like my Grandfather did, in his sleep -- not screaming, like the passengers in his car. "

04-02-2011, 10:29 AM	#5
50bomb Registered User Join Date: Jul 2010 Location: Hemet,Ca Posts: 1,502	Re: What did you do to your truck today! Dropped in my 350/th350 yesterday..Use to be a inline 6 with 3 speed Od. Now to figure why my 2 piece drivehaft is to short...And about 2 inches from even touchin the trans. Any ideas?

04-02-2011, 04:54 PM	#8
70cst Senior Member Join Date: Feb 2001 Location: New Madison, Ohio Posts: 21,375	Re: What did you do to your truck today! Bye Bye __________________ A husband can be right...or...A husband can be happy. 67-72 Chevy and GMC Trucks...The Classic Truck for the Classic Folk. 1970 CST Two tone green, 402BB, 400 Automatic, Tach, Buckets, AC, AM-FM, Tilt, GM CB, GM 8 Tract, LWB, etc JOHN 17:3...The better side of "LIFE" Remember: Everyday is a good day...Some are just gooder!

04-02-2011, 04:30 PM	#11
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Re: What did you do to your truck today! Went and bought a battery and fuel.... Hope to have her out of the garage this evening.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

04-02-2011, 04:33 PM	#12
Garthc20 Registered User Join Date: Nov 2010 Location: san diego ca Posts: 167	Re: What did you do to your truck today! new bowtie today __________________ 1970 Custom camper 20 lwb 1978 yamaha xs1100 (insert clever quote here)

04-02-2011, 06:01 PM	#13
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Re: What did you do to your truck today! Sweet deal I recognized fine69's roll back and had hoped you did not have to sell her at least she is in good hands.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

04-03-2011, 01:08 AM	#14
nickp51chevy Registered Chevy Owner Join Date: Aug 2008 Location: Snohomish, wa Posts: 1,557	Re: What did you do to your truck today! Replaced the ball joints on the right front. Only took all day to get that done....didn't help that we were also working on my brother in law's truck also, and the 10 or more runs to the parts store for tools and/or other parts. But it's done now, and the wheel is nice a solid once again. __________________ Love is fleeting, but Chevy trucks are forever!!!! 1970 Chevy CST C10 long box 350/400 2008 Chevy Silverado short box 4x4 Had; 1951 Chevy short box 307/T5 1988 Chevy shot box 4x4 350/350 1971 Chevy C10 long box 4x4 350/350 1971 Chevy C20 long box 350/350 1971 Chevy C10 long box 350/350

04-03-2011, 02:00 AM	#15
RossRinSD Registered User Join Date: Feb 2010 Location: Fallbrook, CA Posts: 98	Re: What did you do to your truck today! Hai guys, haven't been on in a while. Nice to see everybody is making some progress. I was able to finally install the window my girlfriend got me for Christmas, a tinted sliding rear window.

04-03-2011, 03:39 AM	#16
60ratrod yes, i do Join Date: Jun 2007 Location: Spokane, wa Posts: 2,734	Re: What did you do to your truck today! finished turning my 72 into a flintstonesmobile. the driver's floor pan was pretty much toast, along with my driver's front cab support/mount. as you can see its no longer connected to the rocker. but at least the inner rocker panel is in great shape so i don't have to worry about patching/replacing it. but now i get to fight with the original cab mount bolt that goes under the driver's feet so i can get the cab support/mount off and replaced. my question is do i need the plate that sat under the floor board where the bolt goes through for the mount? if not then i'm getting rid of it. if i do then i'm gonna make a new one. sorry for the hazy photo. friggen cell phones. Attached Images __________________ ERROR 404....... SNAPPY COMEBACK NOT FOUND _______________________________________________________________________________________________ -60 Chevy C10, dead 350/good th350 combo, sitting on a 76 c10 blazer frame, built from 11 different vehicles "the abomination" -07 gmt900 silverado 1500 lt xcab z71, granite blue -81 suzuki gs650g "shelah"- current project -81 kz1000m1 csr "sarge" -next project (just beautification) -07 kawasaki vulcan classic vn900 Last edited by 60ratrod; 04-03-2011 at 03:41 AM.

04-03-2011, 07:56 PM	#17
orange70350 Registered User Join Date: Sep 2009 Location: St. Charles, IL Posts: 43	Re: What did you do to your truck today! i got the clip bed and cab removed Attached Images

04-03-2011, 03:29 AM	#18
pulltilbroke Registered User Join Date: Mar 2008 Location: Eagle Ne Posts: 356	Re: What did you do to your truck today! Got the motor and tranny pulled and started swapping a few things over to the 292!! __________________ 60 4x4,235,SM420,Rockwell T221,D44/HO33 sold 4/12 67 C-20,292,SM420,HO72 90 Dodge W250 Cummins,NV4500HD,205,D60/D80 93 Dodge W350 Dually Cummins, Getrag, 205,D60/D70



Register or Log In To remove these advertisements.

04-03-2011, 09:06 PM	#19
k7elh Registered User Join Date: Jul 2010 Location: Fallbrook, CA Posts: 65	Re: What did you do to your truck today! I watched it continue to rust. __________________ Eric Hutchins 1970 Chevy C10 CST

04-03-2011, 10:01 PM	#20
lil hoodlum Registered User Join Date: Oct 2009 Location: Denton, Texas Posts: 1,735	Re: What did you do to your truck today! Installed new dash pad from LMC. Dashpad was actually boxed and is from DashesDirect. Installed hood letters "chevrolet" and installed new drop shocks (Monroes #5752, 8.625" compressed/ 12.75" extended) Keith Attached Images

04-03-2011, 10:52 PM	#22
bucketObolts Registered User Join Date: Mar 2011 Location: Pequannock NJ Posts: 259	Re: What did you do to your truck today! Well today I spent more time ordering parts than doing actual work but I did manage pull 4 of my air valves out and all wiring out for replacement. Pulled the rear bags off since they are dry rotted and debated whether to change out the fronts too. Didnt have much more to do since im still waiting for a new gun for my MIG, plus i really didnt feel like working on the Painless kit so I used the time to accomplish some much needed toolbox re-organization and tool cleaning.

04-03-2011, 10:53 PM	#23
sjarrett71 Registered User Join Date: Dec 2006 Location: Rolla, MO Posts: 2,463	Re: What did you do to your truck today! I got my manual trans removed and my auto trans installed. It is so much funner to drive now! __________________ -Scott-

04-04-2011, 09:19 AM	#24
6772owner Gearhead Join Date: Jan 2008 Location: Colorado Posts: 1,193	Re: What did you do to your truck today! I installed my Autometer water temp and trans temp in the factory cluster. I put the trans temp in place of the "amp" gauge for now, they never work anyway. I also recalibrated my governor again (7th try) and think I might have a decent calibration for the first time. I also installed a new Kenwood Excelon CD player, OE fog lamps and did an oil change on my Camaro... then went out to the Golden cruise night, great weekend. __________________ 2002 Saturn SL2, My D/D 2019 Ford Fusion SE, Ecoboost - Wife's D/D 1993 Camaro Z28, A4, CAI, Cat-Back Exhaust Project C10 (my 72' C10 w/96' LT1, 700R4, bagged F&R, 18's (for now), Short/Fleet) -- SOLD! Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=313644

04-04-2011, 10:36 PM	#25
Reed's72 Registered User Join Date: Mar 2010 Location: Owasso, OK Posts: 34	Re: What did you do to your truck today! gave into my 14 year old and let her drive around the block, Attached Images

Register or Log In To remove these advertisements.