What did you do with your truck today, Part 3 - Page 82 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

fourspeedwagon · 10-07-2018, 10:06 PM

Brought this home this morning. The poor victim of another guy that can only turn a wrench to the left...
I went through my drawers and found enough of the proper bolts, hung the passenger side door and the hood (fun to hold the door in place and then thread the bolts in- the hood was easy compared to the door).
Needs a new rocker on the right side, but new repros were included. Most of the items removed from the truck are in the bed- except the bolts/screws. I assume he threw those away?
No engine but the trans is there. Odometer says 20,xxx and from the looks of it I’m guessing 120k on the truck.
I’ll update as I peck away at it.

MARTINSR · 10-07-2018, 10:08 PM

Looks like a damn solid truck, going to be nice.

Brian

fourspeedwagon · 10-07-2018, 10:12 PM

Thanks Brian- it really is solid. I was told it was a scrap/parts truck before I went there this morning. Hard to believe the guy was gonna crush her.

MARTINSR · 10-07-2018, 10:39 PM

What a shame that would have been! Thanks to you, this poor old truck will have a second chance.

Brian

MiraclePieCo · 10-08-2018, 01:48 AM

Quote:

Originally Posted by fourspeedwagon

The poor victim of another guy that can only turn a wrench to the left...

Ha ha, that's hilarious - but a real syndrome. It's easy to take a car apart, but it takes money, know-how and dedication to put one back together again. My panel truck was a basket case; it looked like a whole vehicle, but I'll bet replacing all the little missing parts cost me nearly $2000.

MARTINSR · 10-08-2018, 09:41 AM

Quote:

Originally Posted by MiraclePieCo

Ha ha, that's hilarious - but a real syndrome. It's easy to take a car apart, but it takes money, know-how and dedication to put one back together again. My panel truck was a basket case; it looked like a whole vehicle, but I'll bet replacing all the little missing parts cost me nearly $2000.

Yep, I have been effected with that disorter. It makes me want to vomit when I think that I took my FINISHED truck apart 25 years ago for a quick rebuild.

This is why I will suggest to THINK ABOUT IT MORE when people talk about frame "swaps" and crap. I thought I HAD to have a Camaro clip. I cut up a FINISHED truck and ended up trading the frame I did the clip on, (hope he made a good choice and is enjoying it) and am still paying for my mistake.

Yep, this photo is what it looked like the day I started turning the bolts to the left. Can you believe it, I could have been driving it all these years! Geeeez

Brian

**Advanced Design** · 10-08-2018, 12:36 PM

Nice save four speed! Are those a couple AD panels behind it?

DransportGarage · 10-08-2018, 01:02 PM

Shot two coats of clear laced with a small amount of copper pearl today, then unmasked. Dull areas are scuffed only right now. Definitely a "ghost" flag with no shading required, in my opinion. Will shoot an overall three coats of clear in the morning and declare a victory, I hope. Not a "Foose" job, but I'm ecstatic so far...

MARTINSR · 10-08-2018, 01:38 PM

Very cool, I like it! Not overwhelming like many, I dig it.

Brian

mikebte · 10-08-2018, 03:34 PM

Quote:

Originally Posted by MARTINSR

Yep, I have been effected with that disorter. It makes me want to vomit when I think that I took my FINISHED truck apart 25 years ago for a quick rebuild.

Brian

You are a perfect example of why I have not done a complete restore. I do a little and put it back together. Maybe someday if I see large amounts of free time in my future.
I think it also reflects how much care you put into wanting the truck to be right and your demand for perfection has cause many delays in the process. Come completion date that is gonna be one sweet ride.

my56chevytruck · 10-08-2018, 09:15 PM

Quote:

Originally Posted by DransportGarage

Shot two coats of clear laced with a small amount of copper pearl today, then unmasked. Dull areas are scuffed only right now. Definitely a "ghost" flag with no shading required, in my opinion. Will shoot an overall three coats of clear in the morning and declare a victory, I hope. Not a "Foose" job, but I'm ecstatic so far...

You've done a great job on that firewall. Different and beautiful, good job DransportGarage.

lowdownstar · 10-09-2018, 08:33 AM

Quote:

Originally Posted by DransportGarage

Shot two coats of clear laced with a small amount of copper pearl today, then unmasked. Dull areas are scuffed only right now. Definitely a "ghost" flag with no shading required, in my opinion. Will shoot an overall three coats of clear in the morning and declare a victory, I hope. Not a "Foose" job, but I'm ecstatic so far...

Looks Killer

DransportGarage · 10-09-2018, 10:06 AM

Thanks, lowdownstar, MARTINSR and my56chevytruck! Shot the final clear this morning. I may not even scuff & buff.

mikebte · 10-09-2018, 10:12 AM

Quote:

Originally Posted by DransportGarage

Shot the final clear this morning. I may not even scuff & buff.

That's pretty clean looking. Keep it up, gonna look nice under the hood.

MARTINSR · 10-09-2018, 10:16 AM

Got the reinforcement removed from the Left fender and a little sand blasting and stripping. I have to say I did some hack work back in 79 on this fender! LOL

But when I think of that as I am working on it I also think of all the fun I had driving it all those years. THAT is more important sometimes.

Brian

MiraclePieCo · 10-09-2018, 08:28 PM

Finished welding and painting my homemade outside mirror brackets. I made my own because I couldn't find any commercially that had the look and angle that I wanted.

I also cut and fit a piece of 5/8" plywood for my seat pedestal. This will serve as a mount for the bucket seats that came with my truck. The original owner had them bolted to the floor pan but it bent from the weight. This will add reinforcement and something to bolt the seats to. It will eventually be covered in carpet.

DransportGarage · 10-09-2018, 09:11 PM

Quote:

Originally Posted by MiraclePieCo

Finished welding and painting my homemade outside mirror brackets. I made my own because I couldn't find any commercially that had the look and angle that I wanted.

I also cut and fit a piece of 5/8" plywood for my seat pedestal. This will serve as a mount for the bucket seats that came with my truck. The original owner had them bolted to the floor pan but it bent from the weight. This will add reinforcement and something to bolt the seats to. It will eventually be covered in carpet.

This is what hot rodding is all about, for the last 75 years! Nice job on solving problems without ordering something in a box (like I often do)!

MARTINSR · 10-09-2018, 11:58 PM

I didn't know the rear floor was wood like a truck bed! That's friggin cool! I swear if I could afford it I would have a collection of "Working cars" and trucks. Things like that panel that was used in some business, so cool. I picture that floor being covered with boxes of milk or meat, or car parts or something, so cool.

I woke up in the middle of the night with the fit of the fenders to the running boards on my mind. The fender looked so funky I just figured I had to get the running boards out of the attic in the garage and fit them to the fenders. I was right, the left fender wasn't even close, I had to work on it quite a bit to get it there.
Check out the running boards, that's lacquer, look how nice that truck was when I tore it apart 25 years ago, crap!

But I got another step further now.

The little piece of aluminum was my measuring tool when I sectioned it. Just a little tip when you are doing something like chopping or sectioning, make something like that and you can't make a mistake with a measuring tape.

Brian

vintovka · 10-10-2018, 12:05 AM

Quote:

Originally Posted by MARTINSR

I didn't know the rear floor was wood like a truck bed! That's friggin cool! I swear if I could afford it I would have a collection of "Working cars" and trucks. Things like that panel that was used in some business, so cool. I picture that floor being covered with boxes of milk or meat, or car parts or something, so cool.
n

Guarantee they are wood and steel and very uncomfortable to sleep on. Ask me how i know.

MiraclePieCo · 10-10-2018, 02:10 AM

Quote:

Originally Posted by vintovka

Guarantee they are wood and steel and very uncomfortable to sleep on. Ask me how i know.

Uh oh, did your wife make you sleep outside?

I may indeed camp in this panel truck when it's done. It will be replacing my 29-year-old Chevy Astro van which was originally purchased for camping and traveling but now is nearing 500,000 miles. Time to give the old workhorse a well-deserved retirement!

Quote:

Originally Posted by MARTINSR

I woke up in the middle of the night with the fit of the fenders to the running boards on my mind. The fender looked so funky I just figured I had to get the running boards out of the attic in the garage and fit them to the fenders. I was right, the left fender wasn't even close, I had to work on it quite a bit to get it there.
Brian

Heck Brian, tightening the bolts will pull that gap together, ha ha!
Sometimes I suspect Chevy actually wanted some stress on the sheet metal components when they're bolted together, using tension to prevent vibration.

vintovka · 10-10-2018, 03:09 AM

Nah. Camped out in one for months on a cross country trips back in late 60's. The metal strips radiated the cold right thru sleeping bags and blankets. Had to line the back and sides with cardboard.

MARTINSR · 10-10-2018, 11:17 AM

Quote:

Originally Posted by MiraclePieCo

Uh oh, did your wife make you sleep outside?

I may indeed camp in this panel truck when it's done. It will be replacing my 29-year-old Chevy Astro van which was originally purchased for camping and traveling but now is nearing 500,000 miles. Time to give the old workhorse a well-deserved retirement!

Heck Brian, tightening the bolts will pull that gap together, ha ha!
Sometimes I suspect Chevy actually wanted some stress on the sheet metal components when they're bolted together, using tension to prevent vibration.

Understand the photo I show is AFTER I beat the crap out of it to get it that good! It was not close, the fender was buckled with a bunch of welds and crap that I did 30ish years ago so I had to clean that up a bit and get it back to shape. The other side fit WAY better than this without even touching it.

Brian

fourspeedwagon · 10-10-2018, 01:23 PM

Quote:

Originally Posted by Advanced Design

Nice save four speed! Are those a couple AD panels behind it?

Yessir- a late 47 and a 49 AD panel. Good stuff here in the high desert.

**Advanced Design** · 10-10-2018, 03:04 PM

Quote:

Originally Posted by fourspeedwagon

Yessir- a late 47 and a 49 AD panel. Good stuff here in the high desert.

No doubt, they all pretty much rot away around here. Love the color combo on your new truck!

fourspeedwagon · 10-10-2018, 05:12 PM

Quote:

Originally Posted by Advanced Design

No doubt, they all pretty much rot away around here. Love the color combo on your new truck!

Uncle’s friend used to buy cheap rust free cars here and drive them to your area to sell and then buy low mile rust mobiles and bring them here for the drivetrain.

As faded as the color is on the outside, it’s bright and shiny inside.

10-07-2018, 10:06 PM	#2026
fourspeedwagon Registered User Join Date: Oct 2010 Location: Yakima Valley, Washington Posts: 579	Re: What did you do with your truck today, Part 3 Brought this home this morning. The poor victim of another guy that can only turn a wrench to the left... I went through my drawers and found enough of the proper bolts, hung the passenger side door and the hood (fun to hold the door in place and then thread the bolts in- the hood was easy compared to the door). Needs a new rocker on the right side, but new repros were included. Most of the items removed from the truck are in the bed- except the bolts/screws. I assume he threw those away? No engine but the trans is there. Odometer says 20,xxx and from the looks of it I’m guessing 120k on the truck. I’ll update as I peck away at it. Attached Images __________________ 1951 GMC 250 Open Express Pickup 1968 Suburban C10 1971 C20 Olive “People are shocked when they find out I’m not a good electrician” Dad told me “Son, never strike a man in anger- unless you’re certain you can get away with it”

10-07-2018, 10:08 PM	#2027
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: What did you do with your truck today, Part 3 Looks like a damn solid truck, going to be nice. Brian __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

10-07-2018, 10:12 PM	#2028
fourspeedwagon Registered User Join Date: Oct 2010 Location: Yakima Valley, Washington Posts: 579	Re: What did you do with your truck today, Part 3 Thanks Brian- it really is solid. I was told it was a scrap/parts truck before I went there this morning. Hard to believe the guy was gonna crush her. __________________ 1951 GMC 250 Open Express Pickup 1968 Suburban C10 1971 C20 Olive “People are shocked when they find out I’m not a good electrician” Dad told me “Son, never strike a man in anger- unless you’re certain you can get away with it”

10-07-2018, 10:39 PM	#2029
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: What did you do with your truck today, Part 3 What a shame that would have been! Thanks to you, this poor old truck will have a second chance. Brian __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

10-08-2018, 12:36 PM	#2032
Advanced Design Senior Member Join Date: Jul 2012 Location: Oblong, Illinois Posts: 7,028	Re: What did you do with your truck today, Part 3 Nice save four speed! Are those a couple AD panels behind it? __________________ Doug Advanced Design’s 1977 Blazer Build Advanced Design's '48 'Burb Build Mrs Advanced Design's '72 Suburban Advanced Design's 56 BelAir LS swap

10-08-2018, 01:02 PM	#2033
DransportGarage Registered User Join Date: Feb 2010 Location: Lebanon, Ohio Posts: 1,359	Re: What did you do with your truck today, Part 3 Shot two coats of clear laced with a small amount of copper pearl today, then unmasked. Dull areas are scuffed only right now. Definitely a "ghost" flag with no shading required, in my opinion. Will shoot an overall three coats of clear in the morning and declare a victory, I hope. Not a "Foose" job, but I'm ecstatic so far... Attached Images __________________ Bob "It won't take long and it won't cost much." '55 3100 (383/700R4)--'55 Belair Sedan (350/4-speed)--'64 'Vette Conv. (327/4-speed)--'68 GTO Conv. (462/4-speed)--'69 Cutlass Conv. (350/TH350)--'06 'Vette Conv. (LS2/6-speed) Bob's Retirement Build - My 55 TF Bob's 700R4 Build (how-to)

10-08-2018, 01:38 PM	#2034
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: What did you do with your truck today, Part 3 Very cool, I like it! Not overwhelming like many, I dig it. Brian __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

10-09-2018, 10:06 AM	#2038
DransportGarage Registered User Join Date: Feb 2010 Location: Lebanon, Ohio Posts: 1,359	Re: What did you do with your truck today, Part 3 Thanks, lowdownstar, MARTINSR and my56chevytruck! Shot the final clear this morning. I may not even scuff & buff. Attached Images __________________ Bob "It won't take long and it won't cost much." '55 3100 (383/700R4)--'55 Belair Sedan (350/4-speed)--'64 'Vette Conv. (327/4-speed)--'68 GTO Conv. (462/4-speed)--'69 Cutlass Conv. (350/TH350)--'06 'Vette Conv. (LS2/6-speed) Bob's Retirement Build - My 55 TF Bob's 700R4 Build (how-to)

10-09-2018, 10:16 AM	#2040
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: What did you do with your truck today, Part 3 Got the reinforcement removed from the Left fender and a little sand blasting and stripping. I have to say I did some hack work back in 79 on this fender! LOL But when I think of that as I am working on it I also think of all the fun I had driving it all those years. THAT is more important sometimes. Brian Attached Images __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

10-09-2018, 08:28 PM	#2041
MiraclePieCo Registered User Join Date: Sep 2014 Location: USA Posts: 2,249	Re: What did you do with your truck today, Part 3 Finished welding and painting my homemade outside mirror brackets. I made my own because I couldn't find any commercially that had the look and angle that I wanted. I also cut and fit a piece of 5/8" plywood for my seat pedestal. This will serve as a mount for the bucket seats that came with my truck. The original owner had them bolted to the floor pan but it bent from the weight. This will add reinforcement and something to bolt the seats to. It will eventually be covered in carpet. Attached Images __________________ 1951 Chevy Panel Truck

10-09-2018, 11:58 PM	#2043
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: What did you do with your truck today, Part 3 I didn't know the rear floor was wood like a truck bed! That's friggin cool! I swear if I could afford it I would have a collection of "Working cars" and trucks. Things like that panel that was used in some business, so cool. I picture that floor being covered with boxes of milk or meat, or car parts or something, so cool. I woke up in the middle of the night with the fit of the fenders to the running boards on my mind. The fender looked so funky I just figured I had to get the running boards out of the attic in the garage and fit them to the fenders. I was right, the left fender wasn't even close, I had to work on it quite a bit to get it there. Check out the running boards, that's lacquer, look how nice that truck was when I tore it apart 25 years ago, crap! But I got another step further now. The little piece of aluminum was my measuring tool when I sectioned it. Just a little tip when you are doing something like chopping or sectioning, make something like that and you can't make a mistake with a measuring tape. Brian Attached Images __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

10-10-2018, 03:09 AM	#2046
vintovka Registered User Join Date: Aug 2016 Location: Hunkered Down Posts: 1,895	Re: What did you do with your truck today, Part 3 Nah. Camped out in one for months on a cross country trips back in late 60's. The metal strips radiated the cold right thru sleeping bags and blankets. Had to line the back and sides with cardboard. __________________ 1954 USAF 3100 http://67-72chevytrucks.com/vboard/s...d.php?t=714917



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.