67 cheby's Dropmember build thread (CLOUD 9) - Page 83 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Hurst28 · 09-13-2011, 09:53 AM

What is the backspacing on the rear wheels? I really like how close the wheel/tire is to the bedside. Really looks clean that way.

**67cheby** · 09-13-2011, 09:58 AM

the back wheels are 22x10's with 7 1/2 inches of backspacing, but i am running a billet spacer with a 69 up rearend , i couldnt see spending the BIG BUCKS....that it takes to get these kind of wheels custom made to exactly what i wanted so i made these work with the setup i have , bought them on this board in the for sale section...THANKS VA72c10 once again, I LOVE my wheels

**oldman3** · 09-13-2011, 10:40 AM

I take off one day and you add two pages to the build, way to go. Love the tubs and the truck looks great, nice job.....Jim

**67cheby** · 09-13-2011, 10:44 AM

trying to make up for 6 months of adding NOTHING !!

**67cheby** · 09-14-2011, 09:24 AM

did i mention how much i love having my truck at home ..... only had about 1 hour to work on it last night but i started with the used Painless wiring i got from a board member, and stripped all of the tape and loom off it, stripped the wires i didnt need from the engine compartment, and started temporarily routing the wires so i can figure out lengths and routing paths !! It was great if i can get just 1 hour of stuff done a day ...it is MOVING FORWARD !!

68 TT · 09-14-2011, 10:37 AM

Quote:

Originally Posted by 67cheby

did i mention how much i love having my truck at home ..... only had about 1 hour to work on it last night but i started with the used Painless wiring i got from a board member, and stripped all of the tape and loom off it, stripped the wires i didnt need from the engine compartment, and started temporarily routing the wires so i can figure out lengths and routing paths !! It was great if i can get just 1 hour of stuff done a day ...it is MOVING FORWARD !!

What do you have in mind for accessing the anchor bolt for the harness connector? Maybe a tip down access panel so you can get at the anchor bolt but still have it out of sight when not needed.

The panel could cover the whole vent opening to seal it off too.

**67cheby** · 09-14-2011, 11:32 AM

yes i am building a panel that bolts in and out of the vent hole, and then covering in with , custom made speaker kick panels

68 TT · 09-14-2011, 02:04 PM

Quote:

Originally Posted by 67cheby

yes i am building a panel that bolts in and out of the vent hole, and then covering in with , custom made speaker kick panels

That should work nice.

When are you going to drop the drivetrain in there?

72BlckButy · 09-14-2011, 09:13 PM

Lookin' good!

Glad to see it's back home for some regular (ahem,... daily) updates.

**67cheby** · 09-15-2011, 05:23 PM

LOL...yep, gonna get all of my wiring routed for mock up !!

FRENCHBLUE72 · 09-15-2011, 07:17 PM

Please tell me your gonna run that wire under the core support????

**67cheby** · 09-15-2011, 09:58 PM

no it will run through it, completely concealed !! all wire except for the ones running to the absolute necessary stuff will be hidden, along with ac and heater hoses

FRENCHBLUE72 · 09-16-2011, 08:56 AM

Hell yes I was hoping you were gonna say that..

**67cheby** · 09-16-2011, 09:11 AM

yeterday i stopped by a swap meet the first pic is what i couldnt pass up for $10 buckaroos, mocking up my vintage air so i can figure out where to put my computer brain, and where to run my fuel injection wiring out of the firewall (i am thinking in the middle right behind the distributor), then got the box put back in working on getting everything set so i can start stretching the fleece on it to make all of the contours ! oh brought the painless wiring to work with me today to start cleaning it up and checking all of the wires on it !

**67cheby** · 09-16-2011, 12:08 PM

i am thinking about going to GoodGuys on Oct 1st if i can get a couple orders for SLOSH TUBZ, to take and deliver, give me a shout if anyone is interested ! FREE DELIVERY !!

68 TT · 09-16-2011, 12:45 PM

Quote:

Originally Posted by 67cheby

yeterday i stopped by a swap meet the first pic is what i couldnt pass up for $10 buckaroos, mocking up my vintage air so i can figure out where to put my computer brain, and where to run my fuel injection wiring out of the firewall (i am thinking in the middle right behind the distributor), then got the box put back in working on getting everything set so i can start stretching the fleece on it to make all of the contours ! oh brought the painless wiring to work with me today to start cleaning it up and checking all of the wires on it !

Nice score on the valve covers.

The speaker box looks great.

**67cheby** · 09-16-2011, 01:08 PM

thanks..i just cant pass them up i love these valve covers...the box will look alot better once i start stretching the fleece on it , it will really contour nicely then !!

RocketKing · 09-16-2011, 01:12 PM

Quote:

Originally Posted by 67cheby

thanks..i just cant pass them up i love these valve covers...the box will look alot better once i start stretching the fleece on it , it will really contour nicely then !!

How did the speaker box "bend" around the corners? I can't really see how you did that from the pic.

BTW what engine are you looking putting in?

**67cheby** · 09-16-2011, 01:17 PM

it hasnt really "bent" yet the fleece strecthed around the corner and then fiberglassed is what will make the bend This is a pic of the end of the box then i added a piece of 1/4 inch panel to fill the cab corner hole and stretch the fleece to and that will make the curve

**67cheby** · 09-16-2011, 01:20 PM

my engine is a throttle body injected 350 with, eldelbrock tbi intake and holley throttle body, nothing wild just a good dependable FUEL INJECTED cruiser , with 700r4 I think this is the last pic i have with the motor still in it

68 TT · 09-16-2011, 06:58 PM

Quote:

Originally Posted by 67cheby

my engine is a throttle body injected 350 with, eldelbrock tbi intake and holley throttle body, nothing wild just a good dependable FUEL INJECTED cruiser , with 700r4 I think this is the last pic i have with the motor still in it

Nice reliable daily driver of an engine & trans. Same stuff I have going into my 69 K10 project. I have had a few TBI vehicles and they have all done pretty well reliability wise. Good choice to keep things on a realistic budget too.

Dinos63 · 09-16-2011, 07:54 PM

it always nice to get your truck home.... and just go out and look at... for hours at a time

killer work kat

**67cheby** · 09-16-2011, 09:53 PM

Quote:

Originally Posted by 68 TT

Nice reliable daily driver of an engine & trans. Same stuff I have going into my 69 K10 project. I have had a few TBI vehicles and they have all done pretty well reliability wise. Good choice to keep things on a realistic budget too.

my second favorite thing about it is , it still looks like a stock motor !! somewhat original, i have a powdercoated black March serpentine pulley setup ready to install, running the factory style valve covers and breather, cant wait to get some paint on my motor and get it all put together !! i have everything for it just stripped it back down for a better paint job !!

**67cheby** · 09-16-2011, 09:54 PM

Quote:

Originally Posted by Dinos63

it always nice to get your truck home.... and just go out and look at... for hours at a time

killer work kat

LOL...yep been doing that ALOT !! the most heard statement at my house lately WHEN ARE YOU COMING IN ??? UMMMMM in just a minute babe !!

Dinos63 · 09-16-2011, 11:41 PM

Quote:

Originally Posted by 67cheby

LOL...yep been doing that ALOT !! the most heard statement at my house lately WHEN ARE YOU COMING IN ??? UMMMMM in just a minute babe !!

been there

09-13-2011, 09:53 AM	#2051
Hurst28 Registered User Join Date: Sep 2008 Location: Spring TX Posts: 67	Re: 67 cheby's Dropmember build thread What is the backspacing on the rear wheels? I really like how close the wheel/tire is to the bedside. Really looks clean that way.

09-13-2011, 09:58 AM	#2052
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: 67 cheby's Dropmember build thread the back wheels are 22x10's with 7 1/2 inches of backspacing, but i am running a billet spacer with a 69 up rearend , i couldnt see spending the BIG BUCKS....that it takes to get these kind of wheels custom made to exactly what i wanted so i made these work with the setup i have , bought them on this board in the for sale section...THANKS VA72c10 once again, I LOVE my wheels __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

09-13-2011, 10:40 AM	#2053
oldman3 Senior Member Join Date: Mar 2011 Location: West Plains, Missouri Posts: 7,559	Re: 67 cheby's Dropmember build thread I take off one day and you add two pages to the build, way to go. Love the tubs and the truck looks great, nice job.....Jim __________________ my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br />

09-13-2011, 10:44 AM	#2054
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: 67 cheby's Dropmember build thread trying to make up for 6 months of adding NOTHING !! __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

09-14-2011, 09:24 AM	#2055
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: 67 cheby's Dropmember build thread did i mention how much i love having my truck at home ..... only had about 1 hour to work on it last night but i started with the used Painless wiring i got from a board member, and stripped all of the tape and loom off it, stripped the wires i didnt need from the engine compartment, and started temporarily routing the wires so i can figure out lengths and routing paths !! It was great if i can get just 1 hour of stuff done a day ...it is MOVING FORWARD !! Attached Images __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

09-14-2011, 11:32 AM	#2057
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: 67 cheby's Dropmember build thread yes i am building a panel that bolts in and out of the vent hole, and then covering in with , custom made speaker kick panels __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

09-14-2011, 09:13 PM	#2059
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: 67 cheby's Dropmember build thread Lookin' good! Glad to see it's back home for some regular (ahem,... daily) updates. __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package)

09-15-2011, 05:23 PM	#2060
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: 67 cheby's Dropmember build thread LOL...yep, gonna get all of my wiring routed for mock up !! __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

09-15-2011, 07:17 PM	#2061
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Re: 67 cheby's Dropmember build thread Please tell me your gonna run that wire under the core support???? __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

09-15-2011, 09:58 PM	#2062
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: 67 cheby's Dropmember build thread no it will run through it, completely concealed !! all wire except for the ones running to the absolute necessary stuff will be hidden, along with ac and heater hoses __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

09-16-2011, 08:56 AM	#2063
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Re: 67 cheby's Dropmember build thread Hell yes I was hoping you were gonna say that.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

09-16-2011, 09:11 AM	#2064
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: 67 cheby's Dropmember build thread yeterday i stopped by a swap meet the first pic is what i couldnt pass up for $10 buckaroos, mocking up my vintage air so i can figure out where to put my computer brain, and where to run my fuel injection wiring out of the firewall (i am thinking in the middle right behind the distributor), then got the box put back in working on getting everything set so i can start stretching the fleece on it to make all of the contours ! oh brought the painless wiring to work with me today to start cleaning it up and checking all of the wires on it ! Attached Images __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

09-16-2011, 12:08 PM	#2065
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: 67 cheby's Dropmember build thread i am thinking about going to GoodGuys on Oct 1st if i can get a couple orders for SLOSH TUBZ, to take and deliver, give me a shout if anyone is interested ! FREE DELIVERY !! __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

09-16-2011, 01:08 PM	#2067
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: 67 cheby's Dropmember build thread thanks..i just cant pass them up i love these valve covers...the box will look alot better once i start stretching the fleece on it , it will really contour nicely then !! __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

09-16-2011, 01:17 PM	#2069
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: 67 cheby's Dropmember build thread it hasnt really "bent" yet the fleece strecthed around the corner and then fiberglassed is what will make the bend This is a pic of the end of the box then i added a piece of 1/4 inch panel to fill the cab corner hole and stretch the fleece to and that will make the curve Attached Images __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172



Register or Log In To remove these advertisements.

09-16-2011, 01:20 PM	#2070
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: 67 cheby's Dropmember build thread my engine is a throttle body injected 350 with, eldelbrock tbi intake and holley throttle body, nothing wild just a good dependable FUEL INJECTED cruiser , with 700r4 I think this is the last pic i have with the motor still in it Attached Images __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

09-16-2011, 07:54 PM	#2072
Dinos63 chevy only Join Date: Sep 2006 Location: Phoenix, AZ Posts: 6,619	Re: 67 cheby's Dropmember build thread it always nice to get your truck home.... and just go out and look at... for hours at a time killer work kat __________________ CHEVY ONLY... Nothin Else !

Register or Log In To remove these advertisements.