What did you do to your truck today! - Page 84 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ItsRandy · 04-17-2011, 02:11 AM

Well, after fighting with the "exactly like the originals" pre-bent stainless steel brake lines I got from InLine Tubes via GMC Paul's I was able to re-bend the lines so they fit the frame. Because of the experience with the brake lines, I bought 15' of un-bent 3/8 stainless steel tube for my fuel line and bent it myself. Went so well I should have done that with the brake lines.

**Hart_Rod** · 04-17-2011, 08:36 AM

Installed a Vette servo in my 4L60E...

gonnuts · 04-17-2011, 10:29 AM

Pulled motor out, ready to install 406.http://67-72chevytrucks.com/vboard/a...1&d=1303050536

**Daddy Brim** · 04-17-2011, 11:19 AM

I put some paint on the beast. The top is before and the bottom is after.

sjarrett71 · 04-17-2011, 01:30 PM

Drove it to work about 11 miles. Longest trip since the tranny swap and it did great!

DesertCat · 04-17-2011, 01:46 PM

All I've ever done for it... bought parts :-p

Have yet to actually see it in person...

profe56 · 04-17-2011, 04:12 PM

Preparing rear end to swap

Uploaded with ImageShack.us

Scott Webster · 04-17-2011, 04:34 PM

Drove to Lowes for stuff in the addition. Since the T10 got installed, Been a blast to drive. However, next move might need to be a power steering setup!

69trk · 04-17-2011, 05:06 PM

put some rally wheels/spinners on the truck today...

Rob H. · 04-17-2011, 08:42 PM

Did a little more tuning too the carb and used it like a truck!

Also put the original hub caps back on.

jhwkns · 04-18-2011, 12:23 AM

I finally got off of my lazy butt. After a year of running around in primer I'm going to finish my paint job. 98% of the body work was done months ago. I had gotten to a point and stopped. Meanwhile a few other projects were done in front of it.

I backed it into the shed, and my son and I pulled it apart today. It's almost funny how fast you can strip one of these trucks down. I hope to start painting tomorrow.

bucketObolts · 04-19-2011, 08:03 PM

yesterday and today I pulled the front end apart. I am eagerly awaiting new 7" slam specialties bags, tie rod inner and outers, pitman arms, wheel bearings and new drum parts for the rear. Almost bit on the rear disc conversion, but had to just shut off the computer and walk away with my tail between my legs.

SSchevimp · 04-19-2011, 08:51 PM

i pulled the farmer bumper off. along with the "custom" ginormous hitch, pulled the two side fuel tanks that were added off, also took these helper leaf lookin things off ... and ordered some parts

pritch · 04-19-2011, 09:23 PM

I guess I better jump into this thread since I'm working on my new '68.

So far, I've given the cab a good once-over cleaning, fixed the driver's side door latch. Crazy thing wouldn't latch, so I pulled it out and it worked fine in my hand, so I put it back in and now it works fine in the door. Sunday I got the new ball joints and shock and brakes back together-driver's side only, and then today I started on the right side. I got everything apart before I ran outta steam, but going back together is the easy part.

Cooper33 · 04-19-2011, 11:40 PM

Finally got the garage cleaned out, washed the truck and moved into the garage. Want to keep out of the elements until I get a job and can start pouring money into it. To bad I don't have the money, cause I got all the time in the world.

wwotr · 04-20-2011, 03:29 AM

Well actually a couple of days ago......
Stripped off the Black Paint on my 72 GMC Grill.
Afterwards, I'd say it was about a 7.5 out of 10.
Definatley a "50 Footer", but will do until I buy a new Chrome Grill.

flashed · 04-20-2011, 09:59 PM

I bought my 72 a new cowl hood and made a deal on a new front grill assembly by trading a new GM 68 Chevelle fender for it.

Keller · 04-20-2011, 10:34 PM

drove it like i always do

came home to find a box of goodies by the front door...

zellway · 04-21-2011, 11:28 AM

Got my tail lights installed. Also finished the exhast. This weekend will be back on the road.

1quik70 · 04-21-2011, 11:50 AM

I don't have any pic but, I filled mine full of black mulch last week! This week, I have just been beating the old thing back and forth to work like I've done since I bought it last March!

60ratrod · 04-21-2011, 12:16 PM

Finished removing the front driver's cab support and mount bolt. That bolt didn't wanna give in. Now on to removing the front clip to help with installing the new support
Posted via Mobile Device

Jeffs70 · 04-22-2011, 01:42 AM

I modified my Cross Sill so I was able to run my Filler tube up to the bed from my Fuel Cell. also I started to strip the paint from the inside and outside of the bed.
Name: P3290067.jpg
Views: 572
Size: 39.7 KB

Name: P3290067.jpg
Views: 572
Size: 39.7 KB

Name: InsideBedB4-1.jpg
Views: 560
Size: 46.6 KB

Name: InsideBedAfter1.jpg
Views: 558
Size: 43.7 KB

Name: OutsideBed1.jpg
Views: 566
Size: 37.1 KB

Gene · 04-21-2011, 12:17 PM

Got my matching lock set installed that just showed up today from LockDoc. It sure will be nice to use one key when she gets back on the road!

mmmBoost · 04-21-2011, 01:59 PM

Hung my rods and pistons last night. Oh how I hate spiral locks. They can be frustrating when your out of practice...

**FRENCHBLUE72** · 04-21-2011, 02:44 PM

I finally started mine after sitting for 3 months..

04-17-2011, 02:11 AM	#1
ItsRandy Registered User Join Date: Nov 2010 Location: Grand Terrace, Ca. Posts: 1,607	Re: What did you do to your truck today! Well, after fighting with the "exactly like the originals" pre-bent stainless steel brake lines I got from InLine Tubes via GMC Paul's I was able to re-bend the lines so they fit the frame. Because of the experience with the brake lines, I bought 15' of un-bent 3/8 stainless steel tube for my fuel line and bent it myself. Went so well I should have done that with the brake lines.

04-17-2011, 08:36 AM	#2
Hart_Rod ************* Join Date: Apr 2005 Location: Pensacola, FL Posts: 17,846	Re: What did you do to your truck today! Installed a Vette servo in my 4L60E... Attached Images __________________ Rob - https://www.instagram.com/hart_rod_c10 As Iron Sharpens Iron, So One Man Sharpens Another. Proverbs 27:17 FOR SALE: DBW pedal bracket - http://67-72chevytrucks.com/vboard/s...d.php?t=651123 FOR SALE: Hood Brackets http://67-72chevytrucks.com/vboard/s...d.php?t=679945 1987 Silverado SWB - 34.5K original miles http://67-72chevytrucks.com/vboard/s...d.php?t=801834 1969 SuperBurb - http://67-72chevytrucks.com/vboard/s...d.php?t=200387 1968 Farm truck - http://67-72chevytrucks.com/vboard/s...d.php?t=358692 1968 SWB - http://67-72chevytrucks.com/vboard/s...d.php?t=551258 1948 Chevy - http://67-72chevytrucks.com/vboard/s...=122164&page=3

04-17-2011, 10:29 AM	#3
gonnuts Registered User Join Date: Sep 2010 Location: Langdon, Ab Posts: 348	Re: What did you do to your truck today! Pulled motor out, ready to install 406.http://67-72chevytrucks.com/vboard/a...1&d=1303050536 Attached Images

04-17-2011, 11:19 AM	#4
Daddy Brim Senior Member Join Date: Feb 2011 Location: Clovis Ca. Posts: 632	Re: What did you do to your truck today! I put some paint on the beast. The top is before and the bottom is after. Attached Images Last edited by Daddy Brim; 04-17-2011 at 11:20 AM.

04-17-2011, 01:30 PM	#5
sjarrett71 Registered User Join Date: Dec 2006 Location: Rolla, MO Posts: 2,463	Re: What did you do to your truck today! Drove it to work about 11 miles. Longest trip since the tranny swap and it did great! __________________ -Scott-

04-17-2011, 01:46 PM	#6
DesertCat Registered User Join Date: Mar 2011 Location: Valley of the Sunstroke, Arizona Posts: 1,210	Re: What did you do to your truck today! All I've ever done for it... bought parts :-p Have yet to actually see it in person... __________________ My build thread - Devastation and Reform http://67-72chevytrucks.com/vboard/s...d.php?t=567131

04-17-2011, 04:12 PM	#7
profe56 Registered User Join Date: Nov 2008 Location: Chula Vista California Posts: 526	Re: What did you do to your truck today! Preparing rear end to swap Uploaded with ImageShack.us

04-17-2011, 04:34 PM	#8
Scott Webster Sheetmetal Psycho Join Date: May 2005 Location: athens PA Posts: 515	Re: What did you do to your truck today! Drove to Lowes for stuff in the addition. Since the T10 got installed, Been a blast to drive. However, next move might need to be a power steering setup! __________________ I didn't say you were stupid, but I was thinking it... I need a check up from the neck up! Project "Rigginstine's Monster" 1971 C-10 longbed 355/4spd Future mods: 67 front clip Webby's Rigginations - where everything has potential!

04-17-2011, 05:06 PM	#9
69trk Registered User Join Date: Oct 2006 Location: bridgecreek ok. Posts: 1,214	Re: What did you do to your truck today! put some rally wheels/spinners on the truck today... Attached Images __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=494388 431 big block times, changed to a 6.0 ls with turbo 1.58- 60' 7.18- 1/8th mile@95.18 11.37- 1/4 @115.81

04-17-2011, 08:42 PM	#10
Rob H. Registered User Join Date: Nov 2008 Location: Petersville KY Posts: 673	Re: What did you do to your truck today! Did a little more tuning too the carb and used it like a truck! Also put the original hub caps back on. __________________ Rob 72 C/10 (under reconstruction)(destruction ? LOL) 48 Willys CJ2A 1952 Super "A" Farmall (Grandfather's)

04-18-2011, 12:23 AM	#11
jhwkns Registered Cruiser Join Date: May 2002 Location: Las Vegas NV Posts: 2,230	Re: What did you do to your truck today! I finally got off of my lazy butt. After a year of running around in primer I'm going to finish my paint job. 98% of the body work was done months ago. I had gotten to a point and stopped. Meanwhile a few other projects were done in front of it. I backed it into the shed, and my son and I pulled it apart today. It's almost funny how fast you can strip one of these trucks down. I hope to start painting tomorrow. __________________ I intend to live forever. So far, so good.

04-19-2011, 08:03 PM	#12
bucketObolts Registered User Join Date: Mar 2011 Location: Pequannock NJ Posts: 259	Re: What did you do to your truck today! yesterday and today I pulled the front end apart. I am eagerly awaiting new 7" slam specialties bags, tie rod inner and outers, pitman arms, wheel bearings and new drum parts for the rear. Almost bit on the rear disc conversion, but had to just shut off the computer and walk away with my tail between my legs. __________________ LIFESTYLES OF THE POOR & UNKNOWN

04-19-2011, 08:51 PM	#13
SSchevimp Registered User Join Date: Apr 2011 Location: Hesperia Ca Posts: 52	Re: What did you do to your truck today! i pulled the farmer bumper off. along with the "custom" ginormous hitch, pulled the two side fuel tanks that were added off, also took these helper leaf lookin things off ... and ordered some parts __________________ 70 c10 long bed 57 chevy 2 door wagon 07 tahoe 96 civic commuter

04-19-2011, 09:23 PM	#14
pritch Registered User Join Date: Mar 2004 Location: Hoytsville, Utah Posts: 3,365	Re: What did you do to your truck today! I guess I better jump into this thread since I'm working on my new '68. So far, I've given the cab a good once-over cleaning, fixed the driver's side door latch. Crazy thing wouldn't latch, so I pulled it out and it worked fine in my hand, so I put it back in and now it works fine in the door. Sunday I got the new ball joints and shock and brakes back together-driver's side only, and then today I started on the right side. I got everything apart before I ran outta steam, but going back together is the easy part. __________________ '68 Panel Project Boogie Chillin' '68 C-10 Ol' Green

04-19-2011, 11:40 PM	#15
Cooper33 Registered User Join Date: Feb 2011 Location: Round Rock, TX Posts: 125	Re: What did you do to your truck today! Finally got the garage cleaned out, washed the truck and moved into the garage. Want to keep out of the elements until I get a job and can start pouring money into it. To bad I don't have the money, cause I got all the time in the world. __________________ Brad 67 Chevy SWB stepside - http://67-72chevytrucks.com/vboard/s...d.php?t=449426 89 Ford Bronco 92 Suzuki Sidekick 94 Kawasaki Vulcan 750 06 Honda Aquatrax



Register or Log In To remove these advertisements.

04-20-2011, 03:29 AM	#16
wwotr Registered User Join Date: Jan 2005 Location: Clearlake Oaks CA Posts: 1,716	Re: What did you do to your truck today! Well actually a couple of days ago...... Stripped off the Black Paint on my 72 GMC Grill. Afterwards, I'd say it was about a 7.5 out of 10. Definatley a "50 Footer", but will do until I buy a new Chrome Grill. Attached Images __________________ Hello members... I'd like you to know that I sold, my 72 GMC (Ratikle), back in November of 2011. I don't visit the site much anymore, but please feel free, to drop me a private message. RIP...."RATIKLE"

04-20-2011, 09:59 PM	#17
flashed Registered User Join Date: Oct 2009 Location: canton ga Posts: 12,728	Re: What did you do to your truck today! I bought my 72 a new cowl hood and made a deal on a new front grill assembly by trading a new GM 68 Chevelle fender for it.

04-20-2011, 10:34 PM	#18
Keller Registered User Join Date: Sep 2009 Location: Nashville, TN Posts: 79	Re: What did you do to your truck today! drove it like i always do came home to find a box of goodies by the front door... Attached Images __________________ 1972 C10 Longbed 350/350

04-21-2011, 11:28 AM	#19
zellway Registered User Join Date: Dec 2009 Location: Arizona City, AZ Posts: 747	Re: What did you do to your truck today! Got my tail lights installed. Also finished the exhast. This weekend will be back on the road. Attached Images __________________ ----------------------------------------------------------- Erik My 69 suburban http://67-72chevytrucks.com/vboard/s...d.php?t=530626 1970 C10 step Project Jiminy http://67-72chevytrucks.com/vboard/s...d.php?t=682647 RUST!? Thats just mother natures way of telling all of us.....MINE!!!!

04-21-2011, 11:50 AM	#20
1quik70 Registered User Join Date: Apr 2010 Location: Jeffersonville, Indiana Posts: 136	Re: What did you do to your truck today! I don't have any pic but, I filled mine full of black mulch last week! This week, I have just been beating the old thing back and forth to work like I've done since I bought it last March!

04-21-2011, 12:16 PM	#21
60ratrod yes, i do Join Date: Jun 2007 Location: Spokane, wa Posts: 2,734	Re: What did you do to your truck today! Finished removing the front driver's cab support and mount bolt. That bolt didn't wanna give in. Now on to removing the front clip to help with installing the new support Posted via Mobile Device __________________ ERROR 404....... SNAPPY COMEBACK NOT FOUND _______________________________________________________________________________________________ -60 Chevy C10, dead 350/good th350 combo, sitting on a 76 c10 blazer frame, built from 11 different vehicles "the abomination" -07 gmt900 silverado 1500 lt xcab z71, granite blue -81 suzuki gs650g "shelah"- current project -81 kz1000m1 csr "sarge" -next project (just beautification) -07 kawasaki vulcan classic vn900

04-22-2011, 01:42 AM	#22
Jeffs70 Registered User Join Date: Oct 2007 Location: Valley Springs, Ca Posts: 857	Re: What did you do to your truck today! I modified my Cross Sill so I was able to run my Filler tube up to the bed from my Fuel Cell. also I started to strip the paint from the inside and outside of the bed. __________________ My Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=442487 My Picture Gallery http://67-72chevytrucks.com/gallery/...0&ppuser=36004

04-21-2011, 12:17 PM	#23
Gene Registered User Join Date: Aug 2002 Location: Muskogee, Oklahoma Posts: 2,914	Re: What did you do to your truck today! Got my matching lock set installed that just showed up today from LockDoc. It sure will be nice to use one key when she gets back on the road!

04-21-2011, 01:59 PM	#24
mmmBoost Registered User Join Date: Jan 2011 Location: Wisconsin Posts: 224	Re: What did you do to your truck today! Hung my rods and pistons last night. Oh how I hate spiral locks. They can be frustrating when your out of practice... __________________ Always remember those that had your back Never forget those that turned it Demon 68- C20 (conv. 5 lug) 406sb, TH400, 12 Bolt, Red Slut 09- 1500 Crew Cab Z71, 2.5" Lift, Comp Cam, Deleted AFM/DoD, Diablo tuner

04-21-2011, 02:44 PM	#25
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,608	Re: What did you do to your truck today! I finally started mine after sitting for 3 months.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

Register or Log In To remove these advertisements.