10-19-2018, 03:06 PM | #2126 |
Registered User
Join Date: Oct 2011
Location: Tucson, AZ
Posts: 639
|
Re: What did you do with your truck today, Part 3
Removed the diff for new bearings. Also removed my old doff with the 3.38 gears.
|
10-19-2018, 03:56 PM | #2127 |
Registered User
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,174
|
Re: What did you do with your truck today, Part 3
nice job on the fab.
|
10-19-2018, 10:45 PM | #2128 |
Registered User
Join Date: Sep 2014
Location: USA
Posts: 2,249
|
Re: What did you do with your truck today, Part 3
Final mounting of home made mirror brackets. What enables the door edge mounting is these cool flat nuts:
Coolant spewing from under water neck bolt. Generic gasket had too much slop, allowed it to get off-center on installation:
__________________
1951 Chevy Panel Truck Last edited by MiraclePieCo; 10-20-2018 at 05:41 AM. |
10-20-2018, 12:45 AM | #2129 |
Registered User
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
|
Re: What did you do with your truck today, Part 3
Nothing romantic, cleaning up rust on the underside of half the hood, whooo hoooo.
Brian
__________________
1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings" |
10-20-2018, 08:30 PM | #2130 |
Registered User
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
|
Re: What did you do with your truck today, Part 3
First day in a while to spend some decent time on the truck. I did a bunch of stripping and sand blasting on the underside of the hood halves. Got a treatment of Ospho and hope to get them primed tomorrow. If not, Monday morning.
Brian
__________________
1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings" |
10-20-2018, 09:15 PM | #2131 |
Registered User
Join Date: Jun 2017
Location: upper midwest
Posts: 1,129
|
Re: What did you do with your truck today, Part 3
Among other things, I got the Soff Seal door weatherstrip installed. Good stuff...
|
10-20-2018, 10:54 PM | #2132 |
Registered User
Join Date: Feb 2010
Location: Lebanon, Ohio
Posts: 1,359
|
Re: What did you do with your truck today, Part 3
Smart choice.
__________________
Bob "It won't take long and it won't cost much." '55 3100 (383/700R4)--'55 Belair Sedan (350/4-speed)--'64 'Vette Conv. (327/4-speed)--'68 GTO Conv. (462/4-speed)--'69 Cutlass Conv. (350/TH350)--'06 'Vette Conv. (LS2/6-speed) Bob's Retirement Build - My 55 TF Bob's 700R4 Build (how-to) |
10-21-2018, 12:37 AM | #2133 |
Registered User
Join Date: Oct 2011
Location: Tucson, AZ
Posts: 639
|
Re: What did you do with your truck today, Part 3
After 100 successful miles in town I opted to do a test run on the hwy. I learned that at 73-74 the engine stops going. As to what I was unsure and drove home to diagnos. After many hours I opted to go for another drive. I asked the wife to go with and record the systoms. On my 2nd drive I had the same results, cuts out at 73-74 in both 3rd and 4th gear. The wife said it seams like it's governed. Omg, she is onto something. I went home, adjusted the transmission buffer control and calibrated the speedo again. Took it out for a 3rd run and my issue was resolved.
Next I spent some time wrapping up small stuff. Finished the seat belts, moved some wiring and made some repairs to the wiper system. During so I dropped a spring into an AC duct. So I fished my camera in the duct and was able to find the spring. While trying to figure out how to retrieve it, my wife showed up and recommended a hook that goes on my camera, sure enough she saved me a second time. Pieced together the repaired wiper system and stopped for the day. |
10-21-2018, 03:24 AM | #2134 |
Registered User
Join Date: Sep 2016
Location: St. Ingbert/Germany
Posts: 8
|
Re: What did you do with your truck today, Part 3
Spend a little time with paint...
__________________
I know it's cool but no i will not paint it!!! |
10-21-2018, 04:15 AM | #2135 |
Registered User
Join Date: Feb 2010
Location: Lebanon, Ohio
Posts: 1,359
|
Re: What did you do with your truck today, Part 3
Now, that HAS to turn some heads over there in Deutschland!
__________________
Bob "It won't take long and it won't cost much." '55 3100 (383/700R4)--'55 Belair Sedan (350/4-speed)--'64 'Vette Conv. (327/4-speed)--'68 GTO Conv. (462/4-speed)--'69 Cutlass Conv. (350/TH350)--'06 'Vette Conv. (LS2/6-speed) Bob's Retirement Build - My 55 TF Bob's 700R4 Build (how-to) |
10-21-2018, 10:38 AM | #2136 |
Registered User
Join Date: Oct 2011
Location: Tucson, AZ
Posts: 639
|
Re: What did you do with your truck today, Part 3
|
10-21-2018, 01:30 PM | #2137 |
Registered User
Join Date: Jun 2017
Location: upper midwest
Posts: 1,129
|
Re: What did you do with your truck today, Part 3
Windshield time...
|
10-21-2018, 09:23 PM | #2138 |
Registered User
Join Date: Sep 2014
Location: USA
Posts: 2,249
|
Re: What did you do with your truck today, Part 3
FIRST DRIVE!!!
The overriding goal has been to get this truck on the road and worry about the details later. Today I finally got everything buttoned up enough to drive it around the block. The trip was flawless! My impressions: Good: With a Mustang II rack, who needs power steering? Even with such a big truck, manual steering turns with one finger. The engine runs great, stays cool and doesn't leak. Tranny shifts fine. All the gauges work perfectly. Seating position and location of all controls is very comfy. Bad: The brakes need further bleeding. The front springs are sagging severely and need replacement ASAP. My wife said I was driving too fast to get a good photo, but she caught a pic as I brought the truck back to the barn:
__________________
1951 Chevy Panel Truck Last edited by MiraclePieCo; 10-22-2018 at 01:24 AM. |
10-21-2018, 09:26 PM | #2139 | |
Registered User
Join Date: Jun 2017
Location: upper midwest
Posts: 1,129
|
Re: What did you do with your truck today, Part 3
Quote:
|
|
10-21-2018, 10:12 PM | #2140 | |
Registered User
Join Date: Feb 2010
Location: Lebanon, Ohio
Posts: 1,359
|
Re: What did you do with your truck today, Part 3
Quote:
__________________
Bob "It won't take long and it won't cost much." '55 3100 (383/700R4)--'55 Belair Sedan (350/4-speed)--'64 'Vette Conv. (327/4-speed)--'68 GTO Conv. (462/4-speed)--'69 Cutlass Conv. (350/TH350)--'06 'Vette Conv. (LS2/6-speed) Bob's Retirement Build - My 55 TF Bob's 700R4 Build (how-to) |
|
10-21-2018, 10:39 PM | #2141 |
Registered User
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
|
Re: What did you do with your truck today, Part 3
RIGHT ON, DAMN there is nothing better than that first successful drive.
Brian
__________________
1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings" |
10-21-2018, 10:42 PM | #2142 |
Registered User
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
|
Re: What did you do with your truck today, Part 3
Nothing romantic, nothing exciting but I got something done!
Brian
__________________
1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings" |
10-21-2018, 11:14 PM | #2143 |
Senior Member
Join Date: Mar 2011
Location: West Plains, Missouri
Posts: 7,559
|
Re: What did you do with your truck today, Part 3
MPC, congrats on trip around the block...Jim
__________________
my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br /> |
10-22-2018, 02:16 AM | #2144 | ||
Registered User
Join Date: Sep 2014
Location: USA
Posts: 2,249
|
Re: What did you do with your truck today, Part 3
Quote:
Quote:
__________________
1951 Chevy Panel Truck |
||
10-22-2018, 07:58 AM | #2145 |
Senior Member
Join Date: Oct 2016
Location: Olympia, WA
Posts: 523
|
Re: What did you do with your truck today, Part 3
|
10-22-2018, 08:55 PM | #2146 |
Senior Member
Join Date: Oct 2016
Location: Olympia, WA
Posts: 523
|
Re: What did you do with your truck today, Part 3
Test painted the dash to see if I liked it...
|
10-22-2018, 09:00 PM | #2147 |
Registered User
Join Date: Sep 2014
Location: USA
Posts: 2,249
|
Re: What did you do with your truck today, Part 3
You get a "Like" from me! Awesome color!
__________________
1951 Chevy Panel Truck |
10-22-2018, 09:01 PM | #2148 |
Senior Member
Join Date: Oct 2016
Location: Olympia, WA
Posts: 523
|
Re: What did you do with your truck today, Part 3
My bed wood stuff came today.
|
10-22-2018, 09:05 PM | #2149 |
Registered User
Join Date: Feb 2010
Location: Lebanon, Ohio
Posts: 1,359
|
Re: What did you do with your truck today, Part 3
Cherry? That's some awesome stuff !!!
__________________
Bob "It won't take long and it won't cost much." '55 3100 (383/700R4)--'55 Belair Sedan (350/4-speed)--'64 'Vette Conv. (327/4-speed)--'68 GTO Conv. (462/4-speed)--'69 Cutlass Conv. (350/TH350)--'06 'Vette Conv. (LS2/6-speed) Bob's Retirement Build - My 55 TF Bob's 700R4 Build (how-to) |
10-22-2018, 09:06 PM | #2150 |
Registered User
Join Date: Feb 2010
Location: Lebanon, Ohio
Posts: 1,359
|
Re: What did you do with your truck today, Part 3
I'm good with that !!
__________________
Bob "It won't take long and it won't cost much." '55 3100 (383/700R4)--'55 Belair Sedan (350/4-speed)--'64 'Vette Conv. (327/4-speed)--'68 GTO Conv. (462/4-speed)--'69 Cutlass Conv. (350/TH350)--'06 'Vette Conv. (LS2/6-speed) Bob's Retirement Build - My 55 TF Bob's 700R4 Build (how-to) |
Bookmarks |
|
|