MD Parting 72 burb

[cucvzuz]

Originally Posted by richard2717

I should still have a couple if you are talking about the one on the inside that holds the interior panels. Will get some pics in the morning and post them

Yep that's the one I'm looking for.

[richard2717]

How nice are you looking for? I have this set for $50 plus shipping (in PVC tube) has rust but no holes or pitting on the front side that I saw. The back sides had some flake rust that was wire wheeled off. If you are painting them or want to rechrome they would be fine. I have another set floating around here that is way nicer but have yet to put my hands on them. I polished them up with some steel wool and then put them in a safe spot and they seem to be really safe at the moment.

If you want an accurate shipping quote, please pm your full address.

Thanks
Richard


.

[cucvzuz]

Those are the ones I'm looking for but If you can find the real nice set I"d take those, I just repainted the interior.

[Brianhill6]

Interested in the rear sill plate on the green suburban. Any rust in it? I sent a pm

[1968k20]

Originally Posted by richard2717

I have 3 sets and all have rust in the flanges.

You might check with

Budnickguy he is in CA
1968k20 Lisa is in CA
t korinek is in AZ
randy500 is in WA

They have Burb parts as well from time to time

Thanks
Richard

Thanks Richard!
Do you have : 2nd seat front hold downs and some short 2nd/3rd seats?

[richard2717]

Originally Posted by 1968k20

Thanks Richard!
Do you have : 2nd seat front hold downs and some short 2nd/3rd seats?

Lisa
I am out of short seats at the moment.
If you are talking about the front tubular mounts I think I still have a set.
If you are talking about the curved hold downs that clamp the tubular brackets down, I do not have any originals at the moment but they are available aftermarket from several of the board vendors. Here is a link to GMC Pauls

http://www.gmcpauls.com/seat_parts_&_misc_.htm

[richard2717]

Ttt

[Bagd72Chevy]

Do you have any 3rd door hinge pillars?

[richard2717]

Originally Posted by Bagd72Chevy

Do you have any 3rd door hinge pillars?

Nothing that i am ready to get rid of at this time.

[Bagd72Chevy]

Originally Posted by richard2717

Nothing that i am ready to get rid of at this time.

Thanks

[Burb]

Hey Richard
It seems we do need the sealed buckets as well the original was too rusted and I have tabs only
Can you help?

[richard2717]

I have a set I am pretty sure. Let me check them when I get back and will post pics

[richard2717]

Rick,
I have this set here that I saved just for this purpose but let me drop them in the blast cabinet in the morning to make sure there are no weak spots. I think it is all just surface but we all know how that goes.

.

[Burb]

You sir
Are the man

Let me know the $$

Thanks again Richard

[richard2717]

Originally Posted by Burb

You sir
Are the man

Let me know the $$

Thanks again Richard

Rick
Just so we are on the same page........ You only care about the tail and reverse buckets that are spot welded to the panels, correct? SO if I cut away all the un needed metal, the 4 buckets will fit in a medium flat rate and all you will need to do is grind or drill what is left of the quarter panel tabs off of the buckets. I blasted the ruff areas and it all looks good but will still need more blasting done. If you don't have a cabinet I can take care of it for a few bucks more but I need to get them cut apart before doing it.

If we are on same page the 4 buckets shipped flat rate come to $65 like they sit or I can finish bead blasting them for more.

Thanks
Richard

[Burb]

We are on the same page........ I only need the tail and reverse buckets that are spot welded to the panels, correct.

And Blake can blast the rest as they prep them.

I will send it to your Paypal hook up

Thanks again

[richard2717]

All boxed up and labeled. It says 2 days so you should get them Friday

Thanks
Richard

.

[Burb]

Awesome

Thanks again

[ShortbedClayton]

Originally Posted by richard2717

Dwayne
Here is what I have.

two good but not perfect 3rd door sills. One I cleaned up a bit with 0000 wool the other one should do the same


Do you still have the aux. fuel neck and cover from the orange and white doner truck? Also the aux. fuel switch and possibly the aux. fuel tank if available..




I have the filler neck out of the white sub but gotta figure out a way to get rest of locking cap off without a key

Attachment 1767060


I have this area from the same green suburban I can cut out

Attachment 1767059

Or


I have an auxillary gas setup from a parts truck. Same deal here I don't think i have key for the gas cap.

Attachment 1767061

Attachment 1767062

or



I have a 72 Blazer filler that I "might" part with. Not sure if I still have the rear cover, I can't seem to put my fingers on it at the moment. I need to make sure the one in one of my other projects is good b4 I let it go though.

Attachment 1767063

I would need to get them removed to make sure they are decent all the way around. Let me know which one would work better for you.

Posted via Mobile Device

[69-72]

Im looking gas tank brackets. A pair or just the passenger side. Pictured is the drivers side.

[richard2717]

Originally Posted by 69-72

Im looking gas tank brackets. A pair or just the passenger side. Pictured is the drivers side.

I do not have any good ones. I am short one pr for my blazer

[ShortbedClayton]

Do you have the aux. fuel neck and cover plate from the orange and white truck you parted? The neck that is in the bedside?
Posted via Mobile Device

[richard2717]

Originally Posted by ShortbedClayton

Do you have the aux. fuel neck and cover plate from the orange and white truck you parted? The neck that is in the bedside?
Posted via Mobile Device

I do but it may be a while b4 I can get to it. Lots of stuff piled in front.

[ShortbedClayton]

Originally Posted by richard2717

I do but it may be a while b4 I can get to it. Lots of stuff piled in front.

I’m in no hurry keep me in mind. Maybe by next spring I’d be at tht point in the build. I’d be picking it up most likely. Thanks
Posted via Mobile Device

[Madkidd007]

Originally Posted by richard2717

Mike
It looks "ok" in that area except for one small hole on the inner portion where the hatch sits, right at the seam. How far did you need in each direction? I can do the cut for $40 maybe a little less if I don't break any blades, plus shipping.

Richard

.

Interested if you still have these or more from another vehicle.